Code Alarm 420A Bedienungsanleitung

Avoid mounting components or

routing wires near hot surfaces

Avoid mounting components or

routing wires near moving parts

Tape or loom wires under hood

for protection and appearance

Use grommets when routing wires

through metal surfaces

Use a voltmeter for testing and

verifying circuits

PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED

Installation Precautions:

Roll down window to avoid locking

keys in vehicle during installation

FCC COMPLIANCE

This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions:

1.Thisdevicemaynotcauseharmfulinterference,and

2.Thisdevicemustacceptanyinterferencereceived,includinganyinterferencethatmaycauseundesiredoperation.

Warning!

Changesormodificationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidtheuser’sauthoritytooperatetheequipment.

CA 420A Installation Instructions

Kit Contents

(1) - Control Module

(2) - 1 Button High Frequency Transmitters

(1) - 1 Channel Code Learning Receiver

(1) - Multi Pin Harness

(1) - Six Pin Harness

(1) - Four Pin Harness

(1) - Control Switch

(1) - Programming Switch

(1) - Pin Switch

(1) - Remote Start Warning Label

(1) - Literature Package

Note: Do not install this system on a vehicle

that is not equipped with the following:

• Automatic Transmission

• Fuel Injection

• Ignition / Shift Interlock

Technical Support (800) 421-3209

or go to

http://techservices.codesystems.com

WHITE

PARKING LIGHT POLARITY

PARKING LIGHT OUTPUT

BROWN/RED

BROWN

BLACK/WHITE

GRAY

BLACK/GRAY

BLUE/BLACK

GRAY/BLACK

BLACK

PURPLE/WHITE

YELLOW/BLACK

BRAKE INPUT

(+) S HUTDOWN INP UT 1

HOOD PIN INPUT

(+) GLOW PLUG INP UT

ACTIVE OUTPUT

(-) S HUTDOWN INP UT 2

CHASSIS GROUND

TACH INPUT

TO ALAR MS IG NITION INP UT

BLACK/YELLOW

BLACK/RED

BLUE

GREEN/BLACK

(-) PULS E DUR ING C R ANK

(-) PULS E AFTE R S HUTDOWN

(-) PULS E AFTE R S TAR T

(-) PULS E BE FOR E S T AR T

CONTROL SWITCH

PROGRAM

SWITCH

CA-420A

VIOLET

PINK

RED

PINK/WHITE

ORANGE

RED/VIOLET

IGNIT ION 1

12V CONS TANT

IGNIT ION 2

HVAC OUTPUT

12V CONS TANT

STAR TER MOTOR

ANTE NNA

CA 420A

SYSTEM LAYOUT

INSTALLATION OFTHEMAJORCOMPONENTS

ControlModule:

Select a mounting location inside the passenger compartment (behind the dashboard). The mounting location

selected must be within 24" of the ignition switch wiring harness to allow connection of the 6-pin harness. Be

certain that the chosen location will not interfere with the proper operation of the vehicle. Avoid mounting the

module to or routing the wiring around the steering shaft/column, as the module or wiring may wrap around or

block the steering wheel preventing proper control of the vehicle. Secure the module in the chosen location

using cable ties or screws as necessary. Do not mount the module in the engine compartment, as it is not

waterproof.

HOODPIN SWITCH:

The pin switch included in this package is required for the safety shut down of the Remote Start system. If the

vehicle is being serviced, this hood switch prevents the remote start activation even if the transmitter is

operated. This switch MUST be installed in all applications. Failure to do so may result in personal injury or

property damage. Mount the switch in an area under the hood that is away from water drain paths. If necessary,

the included brackets may be used to move the switch away from rain gutters or allow mounting to the firewall

behind the hood seal. In either case the switch must be set to allow the hood to depress the switch at least 1/

4" when the hood is closed and fully extended when the hood is opened. For direct mounting, a 1/4" hole must

be drilled. Carefully check behind the chosen location to insure the drill will not penetrate any existing factory

wiring or fluid lines. Drill a 1/4" hole in the desired location and thread the pin switch into it. If using the

mounting bracket, first secure the bracket to the desired location and secure the pin switch in the threaded

mounting bracket hole.

PROGRAM SWITCH / SAFETY (Red Handled ) CONTROL SWITCH:

Select a mounting location that is within reach of the ignition switch, as this switch, in combination with the

ignition switch and brake, will be used to program the certain features of the system. It is suggested that the

switch be mounted to the lower dash panel in the driver's area. Inspect behind the chosen location to insure

that adequate clearance is allowed for the body of the switch, and also that the drill will not penetrate any

existing factory wiring or fluid lines. Drill a 1/4" hole in the desired location and mount the switch by passing it

through the panel from the underside. Secure the switch using the nut, star washer, and ON/OFF face plate. It is

best to install the switch to allow the ON position to be up toward the driver and the OFF position to be down or

away from the driver. Route the switch wires toward the control module.

The CA-420Ais to be used in vehicles with AUTOMATIC TRANSMISSIONS only! Although this is a

sophisticated system with many advanced features, IT MUST NOT be installed into a vehicle with a manually

operated transmission. Doing so may result in serious personal injury and property damage.

IMPORTANT!

DO NOT PLUG THE SIX PIN OR THE MULTI PIN HARNESS INTO THE CONTROL MODULE UNTILALL

CONNECTIONS TO THE VEHICLE HAVE BEEN MADE. AFTER SELECTING YOUR TARGET WIRES

DISCONNECTTHE NEGATIVE BATTERYCABLEFROMTHEVEHICLEBATTERYPRIOR TOMAKINGANY

CONNECTIONS.

THERECEIVER/ANTENNAASSEMBLY:

The Superheterodyne Receiver Antenna Assembly provided with this system allows routing from below the

dashboard for maximum operating range. Choose a location above the belt line (dashboard) of the vehicle for

best reception. Special considerations must be made for windshield glass as some newer vehicles utilize a

metallic shielded window glass that will inhibit or restrict RF reception. In these vehicles, route the antenna

toward a rear window location for best reception. Secure the antenna with double stick tape provided. After

securing the antenna with tape, we advise also securing a section of the antenna cable to a fixed support. This

will prevent the antenna from dropping down in case the double stick tape is exposed to extreme heat, which

may loosen its gummed surface. Route the 3 pin connector toward the control module using caution not to pinch

the cable as this will cause poor or no RF reception to the control module.

WIRING THE 6 PIN HARNESS:

RED w/ VIOLET:+12volts

Connect this wire to a +12 Volt constant source found at the vehicle's ignition switch. This wire provides power

for the control circuit as well as the ignition 1 and ignition 2 relays.

RED: +12 Volts

Connect this wire to a +12 Volt constant source found at the vehicle's ignition switch but NOT the same vehicle

wire as used by the Red/Violet wire above. Most vehicles have more than one battery source supplying power to

the ignition switch. Separate feed wires must be used for the Red and Red/Violet wires. If your vehicle does not

have two battery feed wires at the ignition switch then it is possible to connect both wires to the vehicle's battery.

This wire provides power for the start relay and the accessory relay.

IMPORTANT!

It is the responsibility of the installing technician to determine the load factor of the vehicles electrical circuits

when the vehicle is running and to adequately fuse the two power wires based on that load.

VIOLET: Starter Output

This wire will have +12 volts when the ignition switch is turned to the start (crank) position only. This wire will

have 0 volts in all other ignition switch positions.

PINK: Ignition 1 Output

Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignition

key is turned to the to the ON, RUN and START positions, and will have 0 volts when the key is turned to the OFF

and ACCESSORY positions. For Diesel Applications, this wire must be connected to the ignition circuit that

powers the glow plugs if the vehicle requires glow plug pre-heating. (See programable features #8)

PINK w/ WHITE: Ignition 2 Output*

Connect this wire to the ignition 2 wire from the ignition switch. This wire will show + 12 volts when the ignition

key is turned to the ON or RUN position and in some cases the START position. This wire will show 0 volts

when the key is turned to the OFF and ACCESSORY positions.

*NOTE: See programable features #2 for programming this wire to function as an ACCESSORY wire.

ORANGE: AccessoryOutput

Connect this wire to the Accessory wire from the ignition switch. This wire will show + 12 volts when the ignition

switch is turned to the ACCESSORY, ON and RUN positions, and will show 0 volts when the key is turned to the

OFF and START positions.

WIRING THE 12 PIN HARNESS:

BLACK: Chassis Ground Source

Connect the BLACK wire to a known vehicle ground source or to a solid clean metal part of the chassis. Be

certain to remove any paint or grease and secure this wire with a self taping screw and ring terminal.

BLACK w/WHITE: Saftey (Red Handled ) Control Switch

The BLACK w/ WHITE wire provides ON-OFF control of the Remote Starter. When the BLACK w/ WHITE wire is

switched to a full time ground, the CA 420A Remote Start Module is operative. When the BLACK w/ WHITE wire

is open, the remote starter is disabled. Connect the BLACK w/ WHITE wire to one of the wires from the back of

the previously mounted Safety (Red Handled) control switch. Connect the remaining wire of the control switch to

chassis ground. Always try to mount the switch so that the ON position is in an upward or toward the driver

direction.

GRAY: Hood Pin Input (-)

Connect the GRAY wire to the hood pin switch provided. This wire will be routed through the firewall into the

engine compartment. It is necessary to use an existing grommet when passing wires through the firewall to

prevent short circuiting. This is an important safety feature of CA 420A, and failure to use this feature can result

in serious injury. Route the wire to the pin switch and connect it using the bullet connector provided.

ORANGE

PINK

RED/VIOLET

VIOLET

PINK/WHITE

RED

BLUE/BLACK

Active out from

12 pin harness* +12Volts in switch position indicated

May be +12 volts in switch position indicated

This circuit is not always required for installation

GRAY w/ BLACK: Negative Shutdown Input 2

Any time the GRAY w/BLACK wire is grounded, the Remote Start system will stop operating, even if the signal is

received from the transmitter. If the brake light switch in the vehicle switches ground to the brake light circuit,

connect the GRAY w/BLACK wire to the output of the brake light switch. If the brake light switch in the vehicle

switches +12 Volts, do not use the GRAY w/BLACK wire; see BROWN w/RED wire.

BROWN Wire: Positive Shutdown Input 1

Any time +12 Volts is applied to the BROWN wire, the Remote Start system will stop operating, even if the signal

is received from the transmitter.If the vehicle has a factory installed hood pin switch, and that switch provides

+12 Volts to a light under the hood, the BROWN wire can be connected to the existing pin switch.

BROWN w/ RED Wire: Positive Brake Input

Any time +12 Volts is applied to the BROWN w/RED wire, the Remote Start system will stop operating, even if the

signal is received from the transmitter. If the brake light switch in the vehicle switches +12 Volts to the brake light

circuit, connect the BROWN w/RED wire to the output of the brake light switch. If the brake light switch in the

vehicle switches ground, do not use the BROWN w/RED wire; see GRAY w/BLACK wire.

Note: The BROWN w/RED wire is used for programming, if the brake switch in the vehicle switches ground, a

normally open push-button switch must be added. During the program sequence, when the brake pedal is

pressed and released, this switch will be used in it's place. If the installation of this switch is necessary,

connect one end of the normally open push button switch to the BROWN w/RED wire, and connect the other end

of the switch to a fused +12 volt source.

Brake Switch Positive Shutdown Detail

YELLOW w/ BLACK: + 12 VoltAlarm By - Pass Output

This wire provides a 500mA +12 Volt transistorized output when the ignition key is turned to the ON position, and

0 Volts when the ignition key is OFF and when the vehicle is running under the control of the Remote Start. This

wire should be connected to the ignition input of the alarm system. The YELLOW w/BLACK wire output will allow

you to Remote Start the vehicle while leaving the alarm armed, and to lock/unlock the doors while running

under control of the remote start system.

(2) WHITE Wires: Parking Light Output

These wires are the COMMON and NORMALLY OPEN contacts of the on-board parking light relay. If the

vehicle's parking lights are a +12 volt switched system, connect (1) of the WHITE wires to a fused (15A max.)

+12 volt battery source, and connect the second WHITE wire to the vehicle's parking light wire. If the vehicle's

parking lights are a chassis ground switched system, connect (1) of the WHITE wires to a chassis ground

source, and connect the second WHITE wire to the vehicle's parking light wire.

BLUE w/BLACK:Active output (-) Ignition 3 / Shock Disable Output

This wire provides a 300mA ground output that becomes active 3 seconds before the Remote Start system

initializes, and remains grounded while running plus an additional 4 seconds after the Remote Start system

turns off. In all of the applications described below, a relay will be required. The BLUE w/BLACK wire can be

used to accommodate the following situations:

1. Shock Sensor Bypass:

If there is Shock Sensor used with an alarm system and it is not shunted during the Remote Start activation

period, then vibration from the running vehicle can cause the alarm to trigger. In this case, connect the Blue/

Black Wire to terminal #86 of a external relay. Connect terminal# 85 of the relay to a fused + 12 volt battery

source. Cut the shock sensor trigger wire and connect one end of the cut wire to terminal #30 and the other end

of the cut wire to terminal #87a. Just before the Remote Start system is activated, the relay contacts will open,

preventing the shock sensor's operation until the Remote Start system shuts off.

2. Ignition 3 Output:

Some newer vehicles use a third ignition wire which is required to start and keep the vehicle's engine running. If

this is the case, connect the BLUE w/BLACK wire to terminal #86 of an external relay. Connect terminal # 30 & #

85 to a fused + 12 volt battery source rated for a minimum of 25 Amp. Connect terminal # 87 to the third ignition

wire in the vehicle.

3. Transponder Key Override:

To bypass the system while the vehicle is operating under the control of the Remote Start system. Connect the

BLUE w/BLACKwire to the NEG trigger input of the accessory bypass.

BLACK w/GRAY: Diesel Wait To Start

For Diesel glow plug preheat circuits, this Wait To Start input will allow the ignition to keep the glow plugs active

for the vehicles automatic time out period before cranking the starter motor. If the BLACK w/GRAY is connected

to the glow plug wire, this will take precedence over the timing setting and the Gas/Diesel programming in the

feature programming chart. Use this wire if you do not want to set the timing of the glow plug preheat circuit as

shown in the programable features chart #8.

Parking Light

Polarity Input WhiteWire From

Remote Start Modu

WhiteWire From

Remote Start Modu

Vehicle Parking Ligh

Vehicle Parking

Light Switch

Max 15 Amp Fuse

PURPLE w/WHITE: Tach Sensor Input

This wire will continually monitor the engine tach rate while the unit is under power of the Remote Start system.

This wire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and

connect to the negative side of the ignition coil. This Remote Start system learns the tach rate of the vehicle and

in most cases will operate properly from one multi coil pack regardless of the number of cylinders. If the vehicle

has a single coil system for each cylinder, it may be necessary to connect this wire to more than one coil for

proper tach reference. Shown in the programablefeatures chart #4.

WIRINGTHE 4PINHARNESS:

This harness provides low current outputs to control various functions in the vehicle during different stages of

the Remote Start system's operation. Understanding these outputs and the time in which they occur will allow

you to determine if they are needed for the particular vehicle you are working on, as well as how to use them.

GREEN w/BLACK: Pulsed GroundOutputBeforeStart

The GREEN w/BLACK wire will provide a 1 second 300mA pulsed ground output 1.5 second before the remote

start system activates as well as when the transmitter is used to unlock/disarm the system. Typical use for this

output would be to disarm a factory theft deterrent system to prevent false triggering of the factory alarm when

the Remote Start system engages.

BLUE: Pulsed Ground OutputAfter Start

The BLUE wire will provide a 1 second 300mA pulsed ground output after the vehicle is started under control of

the Remote Start system. Typically this wire will be used to re-lock the vehicle doors if the doors unlock

automatically when the factory anti-theft system is disarmed.

BLACK w/RED: Pulsed Ground OutputAfter Shutdown

The BLACK w/RED wire will provide a 1second 300mA pulsed ground output after the Remote Start system

shuts down. This output will occur regardless of whether the circuit times out or is manually terminated.

Typically this output will be used to re-lock the vehicle doors if the doors unlock automatically when the ignition

circuit transitions to OFF.

BLACK w/YELLOW: Ground Output During Start (Crank)

The BLACK w/YELLOW wire will provide a 300mA ground output while the starter output of the Remote Start

system is active. This output can be used to activate the Bulb Test wire found in some GM vehicles.

2 Pin Blue Connector : Programming Switch

Route the GRAY and BLACK wires in the 2 pin connector from the previously installed programming switch to

the control module and plug it into the mating blue connector on the side of the module.

3 Pin Antenna/Receiver Connector: (White Connector)

Plug the previously routed three pin connector from the antenna receiver assemble into the mating connector of

the control module. This connector supplies 12 volts, ground and RF data from the antenna receiver to the

remote start module. Be certain this connector is firmly seated making good contact to the control system.

NOTE: Once you enter the programming mode, do not allow more that 15 seconds to pass between steps, or

the programming will be terminated.

PROGRAMMABLEFEATURES:

Feature LtsFlash1X Lts Flash 2X Lts Flash 3X Lts Flash 4X Default

1. Run Time 5 Min. 10 Min. 15 Min. 20 Min. 10 Min.

2. Ign. 2 Off during Crank On during Crank On

3. Parking Lights ON Flash ON

4. Tach Mode Tachless Tach Tach

5. Voltage Level > 0.5V B4 Start < 0.5V B4 Start >0.5V

6. Diagnostics Off On Off

7. Crank Time 0.8Sec 1.0 Sec 1.5 Sec 2.0 Sec 1.0

8. Gas/Diesel Gas Diesel 10 Diesel 15 Diesel 20 Gas

9. BTN Press 1 Press Start 2 Press Start 2 Press Start

To Program Features:

1. Turn the ignition key to the ON position.

2. Press and release the program switch 3 times.

3. Immediately turn the ignition key OFF, then back to ON.

4. Press and release the program switch 2 times.

5. Use the program switch to advance to the feature that you want to change. EXAMPLE - If you need to change

programmable feature number 3, press and release the program switch 3 times in succession. The parking

lights will flash 3 times confirming that selected feature 3 can now be programmed.

7. Press The Vehicle's Brake to change the selection of the programmable feature.

TACHPROGRAMMING:

The Remote Car Start will learn the tach rate of most vehicles single ignition coils, multiple coil packs, and or

single injector. To learn tach:

1. Turn the ignition key to the ON position.

3. Press and release the program switch 3 times.

4. Immediately turn the ignition key OFF.

5. Hold the program switch ON, then start the vehicle using the ignition key.

6. When the system senses the tach signal, the parking lights will begin to flash.

7. Release the program switch. The parking lights will turn on for 3 seconds to indicate that the tach signal is stored

and the system is now out of the program mode.

DIAGNOSTICS:

1. Be sure that programmable feature number #6 is set to the "Diagnostics On" mode.

2. Press and hold the program switch on, then turn the ignition key to the ON position.

3. The lights will flash and the number of flashes will indicate the reason for shutdown on the last remote start

attempt. The indications are as follows.

1 Flash 5, 10, 15, or 20, minute run timer expired.

2 Flashes Low or No tach signal received.

3 Flashes Positive or Negative input shut down.

4 Flashes Control switch was moved to OFF position.

5 Flashes RF Shutdown command received.

6 Flashes High RPM signal over speed shut down.

7 Flashes Tach has NOT learned.

TRANSMITTER PROGRAMMING:

This transmitter is designed for use with your remote start system and is programmed by using the remote

start's program switch in combination with the transmitter button. To program this transmitter into the CA-420A

system:

1. Turn the ignition to the on position.

2. Press and release the programming switch 3 times.

3. Press and hold, for 3 seconds, the button of the transmitter you wish to add until the parking light flashes

indicating the transmitter has been learned.

4. Repeat step 3 for each transmitter up to a total of 4.

Turn the ignition off to exit the program mode.

Inhaltsverzeichnis

Andere Code Alarm Autoalarmanlage Handbücher

Code Alarm

Code Alarm CA1B5 Bedienungsanleitung

Code Alarm

Code Alarm TW-1 Bedienungsanleitung

Code Alarm

Code Alarm Elite CA6155e Bedienungsanleitung

Code Alarm

Code Alarm CSI-300 Bedienungsanleitung

Code Alarm

Code Alarm CA1355E Bedienungsanleitung

Code Alarm

Code Alarm ca 1151 Bedienungsanleitung

Code Alarm

Code Alarm Professional ca6153 Bedienungsanleitung

Code Alarm

Code Alarm CA 6151 Bedienungsanleitung

Code Alarm

Code Alarm CSI-200 Bedienungsanleitung

Code Alarm

Code Alarm CATX520 Betriebsanleitung

Code Alarm

Code Alarm CATX120 Betriebsanleitung

Code Alarm

Code Alarm F20 Bedienungsanleitung

Code Alarm

Code Alarm ca 2051 Bedienungsanleitung

Code Alarm

Code Alarm ca1555 Bedienungsanleitung

Code Alarm

Code Alarm CA611 Bedienungsanleitung

Code Alarm

Code Alarm Car Alarm CA-310 Bedienungsanleitung

Code Alarm

Code Alarm caSEC Installations- und Betriebsanleitung

Code Alarm

Code Alarm PROFESSIONAL SERIES Bedienungsanleitung

Code Alarm

Code Alarm CA 420 Bedienungsanleitung

Code Alarm

Code Alarm CA 1550 Bedienungsanleitung

Code Alarm

Code Alarm ca1153 Bedienungsanleitung

Code Alarm

Code Alarm CA 521 Bedienungsanleitung

Code Alarm

Code Alarm ca 1051 Bedienungsanleitung

Code Alarm

Code Alarm Power Elite PC 4100 Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Ultra Start

Ultra Start 450 SERIES Bedienungsanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Excalibur

Excalibur AL-1860-EDPB Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung