Code Alarm CA 5051MT Bedienungsanleitung

12010AudiovoxElectronicsCorporation.Allrightsreserved.

PROFESSIONAL

SERIES

IMPORTANT NOTE: Theoperation ofthe Securityand ConvenienceSystem as describedin thismanual is

applicableto most vehicles.However, dueto the configurationof somevehicles, some functionsAND/OR

SAFETYPRECAUTIONS maynot apply. Please see your installingdealerfor moreinformation.

Manual Transmission Remote

Start and Keyless Entry System

CA 5051MT

Owner’s Guide

2 2010AudiovoxElectronicsCorporation.Allrightsreserved.

Table of Contents

Using Your Remote Control ...............................................................3

Using the Keyless Entry ...................................................................3

Two Stage Door Unlock (optional) ...................................................3

Activating Trunk Release (optional) ................................................3

Using the Progressive Car Finder Feature......................................3

Using the Personal Protection Alarm ...............................................3

Programmed Transmitter Notification ..............................................3

Valet Mode ........................................................................................4

Eliminating Lock / Unlock Notification Chirps ...................................4

Using Your Remote Control ...............................................................4

Remote Start Ready Mode................................................................4

Cancelling Remote Start Ready Mode .............................................5

Remote Starting Your Vehicle ..........................................................5

Remote Start Shutdown ...................................................................5

Entering Your Vehicle while it is Running via Remote Start ...........5

Preheating or Precooling the Vehicle’s Interior ...............................5

User Programmable Run Time / Run Time Extension ......................6

Remote Start Safety Features .........................................................6

Transmitter Button Functions ...........................................................6

Replacing Remote Control Batteries...............................................7

Warranty Information...........................................................................8

32010AudiovoxElectronicsCorporation.Allrightsreserved.

Using Your Remote Control

Using the Keyless Entry

The button is used to lock the vehicle's doors, the button is used to unlock the

vehicle's doors. To lock or unlock the doors simply press and release the desired

function button one time. For your convenience, the parking lights will flash once

when the doors are unlocked and twice when the door are locked.

NOTE: The system is defaulted with Silent Choice enabled, which requires a

second press of the or button to activate an audible locking/unlocking

response from the vehicle. If your system is set up for 2 step unlock, a third press

of unlock will activate the audible response.

Using the Progressive Car Finder Feature

Press the button to locate your vehicle. The system will sound 5 times at low

volume, increasing in volume each time the button is pressed.

Using the Personal Protection Alarm (Panic)

Press and hold the button for 3 seconds to activate the personal protection

alarm. During panic mode, the normal function of the transmitter buttons will be

suspended. The transmitter’s and buttons can be used to lock and unlock the

door (if the option is installed). To stop the alarm, press and hold the button on

the transmitter again for 3 seconds. The system will automatically stop after 30

seconds.

Programmed Transmitter Notification

As a security precaution each time the vehicle’s ignition is turn on the status LED

light with flash the number of transmitters programmed into the system. This helps

to identify unauthorized transmitters from accessing your vehicle. If you believe an

unauthorized transmitter has been programmed to your system, contact your

installing dealer for assistance.

Activating the Trunk Release Feature (Optional)

The button is used to open the trunk of the vehicle. To open the vehicle's trunk

press and hold the button for 3 seconds.

Two Stage Door Unlock (Optional)

If this feature is enabled on your system, pressing the button one time will

unlock only the driver’s door. Press again within three seconds to unlock the

remaining doors.

4 2010AudiovoxElectronicsCorporation.Allrightsreserved.

Using Your Remote Starter

Valet Mode

Valet Mode is used to disable the system from remote starting. To enter or exit

valet mode simply follow the 4 steps outlined below:

1. Turn the vehicle’s ignition ON.

2. Push and hold the programming/valet button.

3. The LED will turn on solid when valet mode is active

4. Release the programming/valet button.

Remote Start Ready Mode

To activate the remote start function, the system must first be in Remote Start

Ready Mode. Follow the steps below to enter remote start ready mode.

1. While the engine is running by the ignition key;

a. Set the parking brake

b. Place the transmission in neutral.

2. With your foot off the brake pedal, press and release the button 2

times within 2 seconds. The LED will flash 3 times and the parking

lights will turn on to confirm the system has entered quick stop mode.

3. Remove the keys from the ignition, the vehicle will remain running in

quick stop mode.

4. Exit the vehicle and close all vehicle doors.

5. Within 1 minute of step 1, press the button to lock the vehicle’s

doors. The vehicle will shutdown and sound 1 short chirp then 1 long

chirp to confirm ready mode is set.

Eliminating Lock / Unlock Notification Chirps

System lock and unlock notification chirps can be toggled ON or OFF without

entering the programming feature banks.

1. Turn the ignition ON then OFF.

2. Press and release the valet/programming button 3 times. The system

will respond with 1 chirp for ON or 2 chirps for OFF.

52010AudiovoxElectronicsCorporation.Allrightsreserved.

Remote Starting Your Vehicle

To activate the remote start function, press and release the button 2 times within

2 seconds. The system will sound, the parking lights will flash 1 time and the

system will check the vehicle to ensure it is safe to start. If all safety parameters

are correct, the vehicle will start within 5 seconds. The vehicle’s parking lights

will turn on (or flash depending on system settings) as a visual indication that the

vehicle has started and is running.

If your vehicle stalls or does not start, the system will pause 5 seconds, then try 2

more times to start the vehicle (a total of 3 attempts). The system will pause 5

seconds between each start attempt. If the vehicle does not start after the 3rd

attempt, the system will abort the remote vehicle start process.

Note: Do not leave children or animals unattended in the vehicle when using the

remote start feature.

Preheating or Precooling the Vehicle’s interior

Before exiting the vehicle, set the temperature controls to the desired setting and

operation. After the system starts the vehicle, the heater or air conditioner will

activate and heat or cool the vehicle’s interior to your setting.

Remote Start Shutdown

Press and hold the button for 3 seconds to turn the vehicle off.

Entering the Vehicle while it is Running via Remote Vehicle Start

1. Unlock the vehicle’s doors.

2. Enter the vehicle. DONOT PRESSTHE BRAKE PEDAL!

3. Insert the key into the ignition switch and turn to the ON or RUN

position.

4. Press the brake pedal. The remote vehicle starter will disengage and

the vehicle will operate normally.

Cancelling Remote Start Ready Mode

The system will exit remote start ready mode if any of the following occur:

Open any door

Open the hood or trunk (if connected)

Press the brake

Release the parking brake

Turn the ignition ON

6 2010AudiovoxElectronicsCorporation.Allrightsreserved.

Transmitter Button Functions

1 Way

Transmitter

Lock Unlock

Car Find /

Panic

Start Operation Method

Lock X Press and Release

Unlock X Press and Release

Trunk X Push and Hold (3 Sec)

Car Finder X Press and Release

Panic X Push and Hold (3 Sec)

Remote Start X

Press and Release (1 or 2 times

depending on selectable option)

Remote Start

Shut Down

XPush and Hold (3 Sec)

Run Time

Extention

XPress and Release 4 times.

Remote Start Safety Features

For safety and security reasons, the system will shutdown or prevent the remote

vehicle starter from activating if any of the following occur:

1. The vehicle hood is open.

2. The brake pedal is pressed prior to turning the ignition key to the ON

position.

3. The engine is over-reved (tach checking only).

4. Valet mode is active.

User Programmable Run Time / Run Time Extension

The system has the ability to allow the user to extend the time the vehicle will be

running under control of the remote start. This will only extend the run time back to

the current run time setting during the current remote start cycle. If your system is

set to run 15 minutes and the time remaining is 4 minutes, extending the run time

will reset the countdown timer to 15 minutes and your vehicle will continue to run

for another 15 minutes. Follow the steps below to extend the vehicle’s run time.

1. The remote start must already be active.

2. Press and release the button 4 times.

3. The system will chirp to confirm that the run time has been reset.

72010AudiovoxElectronicsCorporation.Allrightsreserved.

Replacing Remote Control Batteries

1-Way Remote Control:

The batteries (model CR2016) inside each remote control should last approximately

1 year under normal use. When the batteries become weak you will notice the

remote control range (the distance from the vehicle the remote control will work)

deteriorate and the small LED on the remote control will dim. To replace the remote

control batteries:

1. Unsnap and disassemble the halves of the remote control.

2. Remove the old batteries, observing the +/- symbols on the batteries

and replace with new CR2016 batteries.

3. Reassemble the halves of the remote control.

4. Test operation of the remote control.

8 2010AudiovoxElectronicsCorporation.Allrightsreserved.

Code Systems, Inc. Limited Lifetime Warranty

Code Systems Inc. (“CODE”) warrants to the ORIGINAL PURCHASER of this CODE vehicle

security product (the “Product”), purchased from an authorized CODE dealer, that (except as

provided below) should this Product under normal use and conditions, be proven defective in

material or workmanship DURING THE LIFETIME OF THE VEHICLE IN WHICH IT WAS ORIGI-

NALLYINSTALLED, such defect(s) will be repaired or replaced (at CODE’s option) without charge

for parts directly related to repairs of the defect(s).

Switches, indicator lights, and transmitter cases are similarly warranted to the original purchaser

for a period of one (1) year from the date of purchase of the Product.

CODE accessories, sold separately, are covered by the applicable warranty accompanying the

accessory.

This warranty is non-transferable, non-assignable and is voided when: (1) the Product is removed

from the vehicle in which it was originally installed; or (2) the vehicle in which the Product was

originally installed is transferred to another party.

This warranty does not apply to any product damaged by accident, physical or electrical abuse,

improper installation, alteration, or use contrary to its intended function, fire, flood, or other

natural acts.

In order for the Product to be repaired or replaced under the terms of this warranty, the defective

Product must be returned to an authorized CODE dealer and accompanied by a copy of the retail

sales receipt. The date of purchase and year, make and model of the vehicle in which the Product

was originally installed must be clearly indicated on the sales receipt.

This warranty is exclusive and CODE MAKES NO OTHER WARRANTIES EXPRESSED OR

IMPLIED. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MER-

CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE

DURATION OF THIS WRITTEN WARRANTY. IN NO CASE SHALL CODE BE LIABLE FOR ANY

CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER

WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER.

CODE does not warrant that the Product cannot be compromised or circumvented. THE EXTENT

OF CODE’S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACE-

MENT PROVIDED ABOVE AND, IN NO EVENT SHALL CODE’S LIABILITY EXCEED THE PUR-

CHASE PRICE PAID BY THE ORIGINAL PURCHASER OF THE PRODUCT WITHOUT INSTAL-

LATION LABOR.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation may not apply to you. This warranty gives you specific legal rights and you may

also have other rights which vary from state to state

92010AudiovoxElectronicsCorporation.Allrightsreserved.

10 2010AudiovoxElectronicsCorporation.Allrightsreserved.

Audiovox Electronics Corporation.

Customer Service 1-800-421-3209

WWW.CODE-ALARM.COM

FCC COMPLIANCE

This device complies with Part 15 of the FCC rules and with RSS-210 of

Industry Canada. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including any interference

that may cause undesired operation.

Warning!

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

Inhaltsverzeichnis

Andere Code Alarm Fernstartsystem Handbücher

Code Alarm

Code Alarm CA 4051 Bedienungsanleitung

Code Alarm

Code Alarm CA-430 Bedienungsanleitung

Code Alarm

Code Alarm CA 1055 Bedienungsanleitung

Code Alarm

Code Alarm PC 4300 Bedienungsanleitung

Code Alarm

Code Alarm ca4053 Bedienungsanleitung

Code Alarm

Code Alarm CA1BTW5 Bedienungsanleitung

Code Alarm

Code Alarm CA-520 Bedienungsanleitung

Code Alarm

Code Alarm CA 421 Bedienungsanleitung

Code Alarm

Code Alarm F40 Bedienungsanleitung

Code Alarm

Code Alarm Professional Series CA 4050 Bedienungsanleitung

Code Alarm

Code Alarm PROFESSIONAL SERIES Bedienungsanleitung

Code Alarm

Code Alarm PC 7500 Bedienungsanleitung

Code Alarm

Code Alarm ca5153 Bedienungsanleitung

Code Alarm

Code Alarm ca5554 Professional series Bedienungsanleitung

Code Alarm

Code Alarm ca 4552 Bedienungsanleitung

Code Alarm

Code Alarm RCS2 Bedienungsanleitung

Code Alarm

Code Alarm PC 7400 Bedienungsanleitung

Code Alarm

Code Alarm F60 Bedienungsanleitung

Code Alarm

Code Alarm ca6554 Bedienungsanleitung

Code Alarm

Code Alarm GUARDIAN CPL 100 Bedienungsanleitung

Code Alarm

Code Alarm ca 5152 Bedienungsanleitung

Code Alarm

Code Alarm ca 1051 Bedienungsanleitung

Code Alarm

Code Alarm PROFESSIONAL CASECRS Bedienungsanleitung

Code Alarm

Code Alarm CA-500 Bedienungsanleitung

Beliebte Fernstartsystem Handbücher anderer Marken

AstroStart

AstroStart 803U Bedienungsanleitung

Durite

Durite 0-649-20 Handbuch

EINHELL

EINHELL BT-PS 1000 Handbuch

Linear

Linear ACCESS AK-21 Technische Daten

Soundstream

Soundstream TARANTULA RS.2 Bedienungsanleitung

Jaycar Electronics

Jaycar Electronics MB3752 Bedienungsanleitung

Ultra Start

Ultra Start 72 Series Bedienungsanleitung

ADS

ADS FLASHLOGIC FLRSVW1 Bedienungsanleitung

Selecta

Selecta JS012 Bedienungsanleitung

Black Widow Security

Black Widow Security BW RAS 400 Bedienungsanleitung

Vector

Vector Power City DK080706 Beilage

Profi-Partner

Profi-Partner 46387 Bedienungsanleitung

EZ STARTER

EZ STARTER EZ-45 Bedienungsanleitung

Essex Electronics

Essex Electronics KE-1701 Bedienungsanleitung

EINHELL

EINHELL EGS 3600 Handbuch

Rooboost

Rooboost RB-1750WP Bedienungsanleitung

Schumacher

Schumacher INSTANT POWER IP-75C Bedienungsanleitung

Mazda

Mazda 0000-8F-H28 Bedienungsanleitung