Codonics SLS-WAVE Referenzhandbuch
Technical Brief
SLS-WAVE
qj
Point of
Administration Scanner
Overview
◆
The Codonics SLS-WAVE Point of Administration
Scanner is used in conjuction with the Safe Label System
(SLS Point of Care Station (PCS and integrates with
Epic Anesthesia and Plexus TG’s Anesthesia Touch
TM
Anesthesia Information Management System (AIMS .
The system is used in the operating room to improve
safety and provide accurate, electronic documentation at
the time of administration.
Hardware Setup - SLS/AIMS
1. Insert the four (4 screws through the bracket into the
SLS-WAVE housing and tighten with 3/32 L-key wrench.
2. Remove the cover to the scanner and insert the Ethenet
cable into the Ethernet port.
3. Replace the cover back on the scanner.
Note: An open USB port is required to connect SLS-
WAVE into the computer where the Epic or Plexus
AIMS application is operated.
4. Insert the SLS-WAVE scanner into the SLS-WAVE
housing.
5. Make sure the USB cord is coming out the back.
6. Connect the SLS-WAVE to the bracket that supports the
AIMS monitor or an IV pole near the patient as shown
below.
WARNING: The scanner should be pointing down and
positioned to keep the scanner light from shining in the
patient’s or user’s eyes.
7. Insert the SLS-WAVE USB into the AIMS computer.
Epic Anesthesia Setup
1. If you don’t have barcoding enabled in Epic, follow the
instructions in
https://galaxy.epic.com/?#Browse/page=8200!68!50!96
6749,966752,11351104.
2. If you have barcoding enabled in Epic and need to enable
scanning in the intraprocedure grid field:
◆
In Clinical Administration, access EMR System
Definitions and follow the path Specialities, Other
Modules > Anesthesia.
◆
Go to the Anesthesia Barcode Scan Settings screen.
◆
Enter Yes in the Allow barcode scanning from
intraprocedure grid field.
Wor flow
1. Log into Epic. Go to Epic Anesthesia work space.
2. Select a Patient in Epic.
3. Scan a vial(s on SLS PCS.
4. Prepare and label all the syringe(s with the label(s from
step 3. The label(s will look similar to the following
example:
5. When ready to administer the syringe(s to the patient,
scan the label’s 1-D barcode using SLS-WAVE.
Note: USB extension cords are available if required to
reach from the SLS-WAVE to the AIMS computer. They
can be ordered using Codonics’ Part Number SLS-
WAVE-USB-EXT.
Note: During setup, you should have access to your Epic
“expert” and/or Epic resources available.
Note: SLS PCS should be loaded with a minimum of
2.3.0 SW and configured to use EHR-1 label template.
EHR-1 template requires the AT configuration to be set
to Primary Barcode #7. This template prints a 1-D linear
barcode.
Note: SLS PCS can be configured for printing 2-D
datamatrix barcodes. By default, the SLS-WAVE will not
read these barcodes. Contact Codonics Technical
Support if you would like to read these barcodes.
Note: The vial’s NDC needs to be in both the SLS
formulary and the site’s Epic Preference List formulary.
17991 Englewood Drive
Middleburg Heights, OH
44130 USA
1.440.243.1198
1.440.243.1334 Fax
Email info@codonics.com
www.codonics.com
Get it all with just one call
800.444. 98
All registered and unregistered trademarks are the property of their
respective owners. Specifications subject to change without notice.
Patents: www.codonics.com/ip/patents.
Copyright © 2017 Codonics, Inc. Printed in the U.S.A. Part No. 901-286-001.06.
Codonics Limited KK
AQUACITY 9F,
4-16-23, Shibaura
Minato-ku, Tokyo,
108-0023 JAPAN
81-3-5730-2297
81-3-5730-2295 Fax
Codonics Trading Co, Ltd.
317 Xianxia Rd. Building B
Unit 1412
Changning Dist., Shanghai
P.R. China, 200051
86-21-62787701
86-21-62787719 Fax
6. When the barcode is scanned, SLS-WAVE will beep,
automatically populate Epic Anesthesia with the NDC,
and displays (as shown below the drug name, color of
the drug classification and identify (circled below if
there are allergies for the drug for that patient with an
icon.
7. Touch or click on the time the drug was administered.
The dose screen will automatically open.
8. Enter the dose and select Close. The drug administration
is now complete in Epic.
9. Repeat step 5 as required with additional syringe(s .
Cleaning SLS-WAVE
To clean the system, use a clean, lint-free cloth moistened
with one of the following approved cleaning agents:
◆
Bleach and water (1:5
◆
70% isopropyl alcohol
◆
Super sani cloth
qÉÅÜåáÅ~ä=pìééçêí
If problems occur during software installation or operation,
contact Codonics Technical Support at any time.
Phone: +1.440.243.1198
Email: [email protected]
Website: www.codonics.com
Note: The SLS-WAVE can be set to one of three levels of
beep volume when scanning; high, medium, or low. To
change the volume, slide the scanner out of the housing
and press the button on the right front corner of the SLS-
WAVE to the required level. Insert the scanner back into
the housing.
Andere Codonics Medizinische Geräte Handbücher
Codonics
Codonics Virtua Bedienungsanleitung
Codonics
Codonics Virtua Bedienungsanleitung
Codonics
Codonics Virtua Bedienungsanleitung
Codonics
Codonics Virtua E Bedienungsanleitung
Codonics
Codonics SLS550i Bedienungsanleitung
Codonics
Codonics Horizon G2 Bedienungsanleitung
Codonics
Codonics Virtua Bedienungsanleitung
Codonics
Codonics Infinity Referenzhandbuch
Codonics
Codonics Safe Label System 550i Bedienungsanleitung
Codonics
Codonics Virtua E Bedienungsanleitung
Beliebte Medizinische Geräte Handbücher anderer Marken
TekTone
TekTone Tek-CARE160 Bedienungsanleitung
NeuroMetrix
NeuroMetrix Quell 2.0 Bedienungsanleitung
AMT
AMT XLR8 Bedienungsanleitung
Medipost-Nutristoma
Medipost-Nutristoma MD300K2 Bedienungsanleitung
EDAN
EDAN SONOTRAX Pro Bedienungsanleitung
Restorative Therapies
Restorative Therapies RT300 Bedienungsanleitung
