Coleman 9943 Series 9943-780 Bedienungsanleitung

ASSEMBLY

INSTRUCTIONS FOR

9943 SERIES

GAS BARBECUE GRILL

9943-054 (04/26/02)

LOOK INSIDE FOR:

Easy Assembly Instructions

Repair Parts List

Safety, Maintenance

and Cleaning Tips

Coleman Company, Inc.

3600 N. Hydraulic

Wichita, KS 67219

Internet site:

www.coleman.com

1-800-356-3612

TDD: 316-832-8707

9-Volt

Battery

Included

LP Tank

Sold

Separately

WARNING:

THE EDGES OF SHEET METAL PARTS CAN CAUSE INJURY

IF NOT HANDLED WITH CARE.

USE EXTREME CAUTION!

IMPORTANT!

TO ENSURE PROPER GAS FLOW, BURNER

CONTROL VALVES MUST BE “OFF” BEFORE

OPENING THE GAS CYLINDER VALVE.

AASSSSEEMMBBLLEERR//IINNSSTTAALLLLEERR::

LEAVE THESE INSTRUCTIONS WITH THE CONSUMER.

CCOONNSSUUMMEERR//UUSSEERR::

READ ALL THESE INSTRUCTIONS AND KEEP THEM IN A

SAFE PLACE FOR FUTURE REFERENCE.

WARNING

Combustion by-products produced when using this product contain

chemicals known to the State of California to cause cancer, birth

defects, or other reproductive harm.

(Pg. 2)

ÖÖ#2 Phillips Screwdriver

ÖÖ3/8”, 7/16” and 11/16” Open End Wrenchs

ÖÖ3/8” Square Drive Ratchet Wrench

ÖÖ3/8” Square Drive Extension

ÖÖElectric or Cordless Screwdriver

ÖÖ#2 Phillips driver bit

ÖÖ#T-20 6-Lobe Screwdriver

TORX BIT SOCKET INCLUDED

ADDITIONAL TOOLS NEEDED:

OPTIONAL TOOLS:

ÖÖ#T-20, 3/8” Square Drive Torx Bit Socket

(Pg. 3)

1-A

1-A. Assemble the Electrode to the Left Burner

Casting using one self-tapping screw (KE).

ÖÖTighten all fasteners.

ÖÖAssemble the Electrode to the Left Burner Casting per illustration (1-A).

ÖÖAssemble the Electrode to the Right Burner Casting illustration (1-B).

Step

1-B KE

Electrode

Right Burner Casting

Electrode

Left Burner Casting

1-B. Assemble the Electrode to the Right Burner

Casting using one self-tapping screw (KE).

ÖÖTighten all fasteners.

(KE)

#6-32 x 3/8 Self-tapping Screw

(2) Qty.

Hardware shown actual size

(Pg. 4)

ÖÖNOTE: The grill is upside-down during this

assembly step.

ÖÖAssemble the CONSOLE CASTINGS.

ÖÖUse a large piece of cardboard or a ground

cloth to protect the painted finish on the

castings.

ÖÖLay all three castings on a level surface with

the top (smooth) surface downward.

2-A

2-B.Assemble the Right Console Casting to the Center Console Casting. Three Alignment Pins

mate with three Alignment Holes in castings. Fasten with four SCREWS (MG) and four HEX

NUTS (BV) and one Clip (NH). See Detail 2-C and Detail 2-D for location of Clip (NH).

Tighten the fasteners.

ÖÖRepeat Step 2-B to assemble the Left Console Casting to the Center Console Casting.

2-A. Lay all three castings on a level surface with the smooth

(top) surface downward.

2-B

Right Console Casting

Left Console Casting

Center Console Casting

Step

(MG)

1/4-20 x 7/8 Hex Head Cap Screw

(8) Qty.

Hardware shown actual size

Hardware

shown actual

size

(BV)

1/4-20 Hex Nut

(8) Qty.

(NH)

Clip

(2) Qty.

Right Console Casting

Alignment Pin

Alignment Hole

NH MG

Another

View of

Clip (NH)

2-C 2-D

(Pg. 5)

ÖÖNOTE: The grill is upside-down during this assembly step.

ÖÖAssemble the Tool Rack to the console.

ÖÖAssemble the Towel Rack to the console.

3-A

Step

Squeeze

the Towel

Rack to

slip into

the

mounting

holes.

Squeeze

the Tool

Rack to

slip into

the

mounting

holes.

(Pg. 6)

ÖÖNOTE: The grill is upside-down during this assembly step.

ÖÖAssemble the 9-VOLT BATTERY to the ELECTRODE MODULE.

ÖÖAttach two wires (27” long) from the ELECTRODE MODULE labeled LB1 and LB2 to the LEFT BURNER (thread thru wire clip).

ÖÖAttach two wires (27” long) from the ELECTRODE MODULE labeled RB1 and RB2 to the RIGHT BURNER.

ÖÖVerify that two wires are attached from the MAIN BURNER to the ELECTRODE MODULE labeled MB1 and MB2 (factory installed).

ÖÖVerify that two wires are attached from the IGNITER BUTTON to the ELECTRODE MODULE on the left side (factory installed).

Step

4-A

4-B

Left Burner

Right Burner

4-C

Right Burner

Electrode Wires

Left Burner

Electrode Wires

Main Burner

Electrode Wires

Igniter Button

Wires

NOTE: Wires are

factory installed to the

Electrode Module.

9-Volt Battery

ELECTRODE MODULE

Left Side

Caution: Insure that the

wires DO NOT touch hot

surfaces such as the grill

casting!

ELECTRODE

MODULE

ELECTRODE

MODULE

MB1

LB1

RB1

MB2

LB2

RB2

Thread Wires

through Wire

Clip

Thread Wires

through Wire

Clip

(Pg. 7)

5-A 5-B

5-C

5-A. Assemble the PEDESTAL LEFT PANEL to the

PEDESTAL BACK PANEL.

ÖÖInsert the flat lip of the PEDESTAL LEFT PANEL

into the curled lip of the PEDESTAL BACK

PANEL, taking care to align the bolt holes.

ÖÖAssemble the PEDESTAL PANELS.

(DX)

#10-24 x 1/2 Self-tapping Screw

(2) Qty. Per Side Panel

Hardware shown actual size 5-C.LOOSELY fasten together with one SCREW (DX).

One at top only.

ÖÖNOTE: You will tighten this screw LATER, after the

panels are fastened to the grill console in Step 8-B

(this helps with alignment).

ÖÖRepeat Step 5 to assemble the RIGHT PANEL.

Pedestal

Left

Panel

Pedestal

Back

Panel

Step

Use Tool Through

Opening

Stop (1) Turn

Before Tight

Pedestal

Back

Panel

Pedestal

Left

Panel

(Pg. 8)

ÖÖAssemble PROPANE TANK RETAINER WIRE to the Pedestal Back Panel.

6-A

6-A. Assemble Propane Bottle Retainer Wire to the Pedestal Back Panel.

ÖÖSqueeze the Wire and insert into Bottle Retainer Bracket on Pedestal Back Panel.

Step

Propane

Bottle

Retainer

Wire

Bottle

Retainer

Bracket

Pedestal Back Panel

(Pg. 9)

ÖÖNOTE: The grill is upside-down during this assembly step.

ÖÖPlace the PEDESTAL onto the CONSOLE.

Step

7-A

7-B

7-C

7-A. Place the PEDESTAL onto the CONSOLE.

ÖÖAlign the studs and pins with the assembly holes.

7-B. Align four studs with holes in

the Center Burner Casting.

ÖÖAlign two pins (part of the

casting) with two holes in the

Pedestal.

7-C. Align two

studs with

holes in the

right pedestal

panel

(shown).

ÖÖAlign two

studs with

holes in the

left pedestal

panel on the

opposite side

(not shown).

Pins (2)

View From Back Of Grill

View From Front Of Grill Console

Pedestal

Studs (4)

Center

Burner

Casting

Pedestal

Right

Pedestal

Panel

Studs (2)

Per Side

(Pg. 10)

ÖÖNOTE: The grill is upside-down during this assembly step.

ÖÖFasten the PEDESTAL to the CONSOLE per Step (8-A).

ÖÖTighten and secure the Pedestal Panel Fasteners per Step (8-B).

Step

8-A

8-B

8-A. Assemble four HEX NUTS (EY),

one on each stud that protrudes up

from the casting into the pedestal

(they can be reached through the

front door opening).

ÖÖAssemble two on the right pedestal

panel (shown in Illustration 7-C and

8-A). and two on the left pedestal

panel (not shown).

ÖÖTighten all fasteners.

8-B. Tighten the two screws (DX) loosely fastened earlier in Step 5-C.

ÖLock the two screws (DX) holding the PEDESTAL PANELS together with (2)

HEX NUTS (EY).

ÖOne HEX NUT (EY) assembles onto the right pedestal panel as shown. One

HEX NUT (EY) assembles onto the left pedestal panel.

ÖTighten all fasteners.

(EY)

#10-24 Hex Nut

(6) Qty.

Hardware shown actual size

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Coleman Grill Handbücher

Coleman

Coleman 9939 Series Bedienungsanleitung

Coleman

Coleman EVEN HEAT G52209 Bedienungsanleitung

Coleman

Coleman 9926 Series Bedienungsanleitung

Coleman

Coleman REVOLUTION 85-3166-6 Bedienungsanleitung

Coleman

Coleman 9972 Series Bedienungsanleitung

Coleman

Coleman Revolution 85-3118-2 Bedienungsanleitung

Coleman

Coleman 9998 Series Bedienungsanleitung

Coleman

Coleman EvenHeat Series Bedienungsanleitung

Coleman

Coleman 2000 Series LG200-EDB Bedienungsanleitung

Coleman

Coleman Even Heat Barbecue Bedienungsanleitung

Coleman

Coleman 5600 Series 9990-646 Anwendungshandbuch

Coleman

Coleman Even Heat 85-3068-0 Bedienungsanleitung

Coleman

Coleman 9948-725 Bedienungsanleitung

Coleman

Coleman 9957 Series Bedienungsanleitung

Coleman

Coleman 85-3046-2 (G35301) Propane Bedienungsanleitung

Coleman

Coleman 9992-644 Bedienungsanleitung

Coleman

Coleman 4000 Series LG40811E Bedienungsanleitung

Coleman

Coleman 9995A Series 9995A700 Bedienungsanleitung

Coleman

Coleman 9928 Series Bedienungsanleitung

Coleman

Coleman REVOLUTION G53236 Bedienungsanleitung

Coleman

Coleman 9945-700 Benutzerhandbuch

Coleman

Coleman 9995- Series Bedienungsanleitung

Coleman

Coleman 9921A Series Bedienungsanleitung

Coleman

Coleman CM9916 Bedienungsanleitung

Beliebte Grill Handbücher anderer Marken

Orbegozo

Orbegozo GR 2300 Bedienungsanleitung

bora

bora PT11 Bedienungsanleitung

Klarstein

Klarstein 10031664 Bedienungsanleitung

Garland

Garland MWE3W Bedienungsanleitung

Char-Broil

Char-Broil 463722714 Bedienungsanleitung

Nexgrill

Nexgrill 720-0830HK Bedienungsanleitung

Kenmore

Kenmore 415.16123800 Bedienungsanleitung

Tucker Barbecues

Tucker Barbecues GTR Series Montageanleitung

Monogram

Monogram ZGG540NCP1SS Bedienungsanleitung

Equipex

Equipex Sodir Savoy Bedienungsanleitung

Gaggenau

Gaggenau VR 414 610 Bedienungsanleitung

Miele

Miele KM 408-1 Bedienungsanleitung

George Foreman

George Foreman GGR50B Bedienungsanleitung

AOG

AOG T series Bedienungsanleitung

Gorenje

Gorenje TG2000CB Bedienungsanleitung

Weber

Weber Genesis Silver-B Permamount NG 051701 Bedienungsanleitung

Glen

Glen SA 3037 Bedienungsanleitung

Stalgast

Stalgast 9730100 Bedienungsanleitung