Comdial Impact 8024S Series Bedienungsanleitung

Comdial Impact and Impact SCS LCD Speakerphone User’s

Guide

(Not all phones or systems support all features)

Adjusting contrast on your LCD:

1. Select “OPTIONS”.

. Select “NEXT” until the “DISP” option appears.

3. Select “DISP”.

4. Select “LIGHT” or “DARK”.

5. Press “SPEAKER” to end.

Customizing your ring tone:

1. Select “OPTIONS”.

. Select “NEXT” until the “RING” option appears.

3. Select “RING”.

4. Select “UP” or “DOWN” to choose a new ring tone.

5. Press “SPEAKER” to end.

Setting volume levels

Rin er Volume:

While you are not on a call, press the volume up or down buttons. If you set

the ringer to “OFF” you will still hear a short ring for each incoming call.

Speaker Volume:

Press the “INTERCOM” button. Press the volume up or down buttons. (Note:

when you hang up, the volume levels revert to default levels. See below to

change defaults)

Handset Volume:

Lift handset. Press the volume up or down buttons.

(Note: when you hang up, the volume levels revert to default levels. See

below to change defaults)

Advanced

Chan e Default Handset and Speaker Volume:

1. Press “INTERCOM”.

. Activate speaker, headset or handset mode to be affected.

3. Press the volume up or down buttons.

4. Dial ____ (Check with your system administrator – may be “**5” or

“**7”) or programmed SAVE button.

5. Repeat for each (speaker, headset, handset).

Answering Calls

If the phone rings and you do not want to answer it, you can press “DND” now.

Outside Calls (lon tones):

1. Press the flashing line button.

. Speak toward the phone or lift the handset.

Intercom Calls (2 short tones):

1. Press “INTERCOM”.

. Speak toward the phone or lift the handset.

To respond to a call-waitin tone:

Place the current call on hold or complete the call and hang up. This second

call will ring through.

Using the “HOLD” feature

Place a call on hold:

1. Press “HOLD” station button.

Retrieve a call on hold:

1. Press the line button of the held call (light will be blinking) or press

“TAP”.

Call Forwarding

To forward your calls:

1. Select “OPTIONS”.

. Select “NEXT” until you see the “CFWD” option.

3. Select “CFWD”.

4. Choose “SET”.

5. Options:

a. Select “PERS” to forward prime line and intercom calls. Press

“PERS” again.

b. Select “ALL” to forward all calls. Press “ALL” again.

c. Select “NEXT” and “No ANS” to forward calls that ring at your

station but receive no answer after a predetermined number of

rings. Press “ALL” again.

6. Dial the extension number of the telephone to receive your forwarded

calls.

7. Press “SPEAKER” to end. If you have set forwarding up correctly, the

LCD will display “FWD”.

Cancel call forwardin :

1. Select the right interactive button.

. Select “NEXT” until the “CFWD” option appears and select.

3. Select “CLR” to cancel call forwarding.

4. Press “SPEAKER” to end.

Call Forward Outside System (CFOS):

1. Select “OPTIONS”.

. Select “NEXT” until “CFWD” appears.

3. Select “CFWD”.

4. Select “SET”.

5. Select “NEXT” until “CFOS” appears. Select this option.

6. Choose a type of CFOS and select the desired interactive button. To

switch the type of CFOS, press “TGL”.

a. “Itcm” forwards intercom calls.

b. “Line” forwards prime line calls.

c. “Itcm/Ln” forwards all calls.

d. “RNA Itcm” forwards all intercom calls that ring on your station

and are not answered in a specified time period.

e. “RNA Itcm/Ln” forwards all ring-no answer calls.

7. Select an outbound line.

8. Select the forward destination (dial number, press speed dial button).

9. Press “SPEAKER” to end. If set properly, the display will show “CFOS”

along with the type of forwarding.

To cancel CFOS:

Press “INTERCOM” and dial “*56”.

Parking a Call

Parkin a call in orbit – places the call on hold so that it can be answered from any station:

1. While on a call, press “INTERCOM” or “TRNS/CNF” if you are on an

intercom call.

. Dial “*”.

3. Dial code for part orbit (“910” through “999”) for orbit 10-99.

4. Remember the code for retrieving the call.

Retrievin a parked call:

1. Press “INTERCOM”.

. Dial “#”

3. Dial the code for orbit (“910” through “999”) for orbit 10-99.

Handlin park recalls:

When a parked call times out of the system, it returns to your phone. You

will hear 4 short tones at 1 -second intervals.

To answer:

Select “ANS”.

Transferring Calls

To screen and transfer to another phone:

1. Answer the call

. Press “TRNS/CNF”.

3. Dial the extension of the phone you wish to receive the call.

4. Announce the call when the party answers.

5. Press “SPEAKER” or hand up to complete.

If the extension you wish to transfer to is busy or continues rin in :

1. Select “RECON” to reconnect the call to your station.

. Select “SOHVA” to interrupt the call and let the intended recipient

know a call is waiting (for busy signal only).

3. Select “MSG” to leave a message-waiting indication at the called

extension.

To transfer an unscreened call to another phone:

1. Answer the call.

. Press “TRNS/CNF”.

3. Dial the extension or press the DSS/BLF button for the extension.

4. Press “SPEAKER” (if using speakerphone) or hang up to complete.

If an unscreened transfer call is not answered and returns to your

telephone:

1. Press “HOLD” to place the call on hold at your station. Or,

. Select “ANS” to return to the call.

3. Select “SEND” to retry the transfer.

Monitor Status of Another Telephone

Look at the BLF light next to the Direct Station Select (DSS/BLF) button.

Off = Station is idle

Flashing = Station has an incoming call

On = Station is busy

Making Calls

Manually:

1. Press “INTERCOM”

. Select a line and dial the number.

Speed Dialin :

1. Press the programmed speed dial button. If you want the alternate

number stored on that buttons, press “SHIFT” at the same time.

Redialing

Redial Last Number:

1. Press “SPEAKER” or hang up to disconnect current ringing or busy

tone.

. Dial “#”.

Use automatic redial features to redial a busy or unanswered number

while you are on a call:

1. Select “ARDL” or press the automatic redial button programmed by

your installer.

The system will dial the number until you cancel the feature or after a

specific number of tries (set by your installer). The automatic redial light

will flash between redials and will be steady during redialing.

Storin a number you’ve just dialed:

1. Select “SAVE” and press an unused programmable button.

Store a number while you are on a call (not available on all systems):

1. Press the programmed “SAVE NUMBER REDIAL” button twice.

. Following the prompt, dial the number you wish to save. Your call will

not be interrupted.

“Camping On” busy station automatic callback

Settin and usin Campin On:

When you dial the station and you hear the busy signal, select “CAMP”.

When your call is connected, your telephone will ring with 5 tone bursts.

Press “INTERCOM” or “ANS”.

Cancel the call-back request:

Press “INTERCOM” and dial” *6”.

Settin Campin On at a station on “Do Not Disturb”:

Select “CAMP”. When the station is no longer in DND, your call-back request

will go through.

Waiting (Queuing) for a line

When a line becomes available you will hear several short tone bursts.

When all lines are busy:

1. Press “INTECOM”.

. Dial the line group access code.

3. At the busy tone dial “*6”.

To queue for a particular line:

1. Press “INTERCOM”.

. Dial “*6”.

3. Press the desired line button.

Cancel queue:

1. Press “INTERCOM”.

. Dial “#6”.

Conference Calls

Note: When setting up a conference call with both outside and inside phones,

you must connect the outside lines first.

Set up a conference call:

1. Make the first call.

. Select “CONF” (call is placed on hold).

3. Select next line and make the next call.

4. Select “CONF” to establish conference.

5. Press “TRNS/CNF” to add more parties.

To continue conversin with one member of the conference after

other outside lines have dropped out:

1. Press “HOLD”.

. Press the line button of the remaining party.

Brin a caller on hold back into the conference:

1. Press “TRNS/CNF”.

. Press the line button.

3. Press “TRNS/CNF”.

Drop out of a conference call that you initiated:

1. Dial “#”

To rejoin:

1. Press “TAP” or “DSS/BLF” button of one of the conferencing stations.

Andere Handbücher für Impact 8024S Series

Inhaltsverzeichnis

Andere Comdial Telefon Handbücher

Comdial

Comdial Quick Q Bedienungsanleitung

Comdial

Comdial Executech Single Line Telephone Bedienungsanleitung

Comdial

Comdial Impression 2022S series Bedienungsanleitung

Comdial

Comdial DSU II Series Bedienungsanleitung

Comdial

Comdial CONVERSip EP100 Bedienungsanleitung

Comdial

Comdial Scout II Bedienungsanleitung

Comdial

Comdial Conversip EPI00G-L12 Bedienungsanleitung

Comdial

Comdial DX-80 Bedienungsanleitung

Comdial

Comdial GCA70-313 Bedienungsanleitung

Comdial

Comdial GCA70-25 Bedienungsanleitung

Comdial

Comdial Impact 8024S Series Service-Handbuch

Comdial

Comdial Executech Single Line Telephone Bedienungsanleitung

Comdial

Comdial 80245 Bedienungsanleitung

Comdial

Comdial Impact 8012S Series Bedienungsanleitung

Comdial

Comdial DX-80TM Bedienungsanleitung

Comdial

Comdial HoTelephone 3809X Bedienungsanleitung

Comdial

Comdial Impact SCS 8212S Series Bedienungsanleitung

Comdial

Comdial X34PT Bedienungsanleitung

Comdial

Comdial SCS 8324SJ-FB Bedienungsanleitung

Comdial

Comdial GCA70-248 Bedienungsanleitung

Comdial

Comdial DigiTech 7700S Series Bedienungsanleitung

Comdial

Comdial Impact 8012S Series Bedienungsanleitung

Comdial

Comdial 8900-IP Series Bedienungsanleitung

Comdial

Comdial ExecuTech 0616 Series Bedienungsanleitung

Beliebte Telefon Handbücher anderer Marken

GE 2-9480 Bedienungsanleitung

Geemarc

Geemarc PHOTOPHONE 155 Bedienungsanleitung

D-Link

D-Link DWR-720/PW Bedienungsanleitung

Interquartz

Interquartz Gemini IQ333 Bedienungsanleitung

SSS Siedle

SSS Siedle HT 840-0 Bedienungsanleitung

Motorola

Motorola TITANIUM Bedienungsanleitung

Panasonic

Panasonic ICX Bedienungsanleitung

LG H870DS Bedienungsanleitung

Samsung

Samsung GT-I9500 Bedienungsanleitung

AT&T

AT&T Trimline 205 Bedienungsanleitung

Selta

Selta zenyth 600 Bedienungsanleitung

Doro

Doro AFTI 20 Bedienungsanleitung

UNIQCELL

UNIQCELL A1 Bedienungsanleitung

Panasonic

Panasonic KX Series Bedienungsanleitung

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Bedienungsanleitung

BT Decor 425 Bedienungsanleitung

NEC

NEC SV8500 Bedienungsanleitung

Teledex

Teledex PEARL Bedienungsanleitung