Compaq 117755-003 - ProSignia - 740 Kurzanleitung

WHITEPAPER

467A/0197

[January 1997]

Prepared By

Compaq Windows NT

Integration

Compaq Computer

Corporation

CONTENTS

Overview

...........................

Windows NT Features

Not Affected by the

Migration

...........................

Considerations Before

Migrating

...........................

Compaq Migration

Scenarios

..........................

Outline of the Migration

Process

.............................

Backup the Server

...................

Determine Hard Drive

Space Requirements

...............

Disable Startup Settings

..........

Compaq Software Support

Diskette Installation

Overview

................................

Migration Scenario 1

.............

Migration Scenario 2

.............

Migration Scenario 3

.............

Migration Scenario 4

.............

Upgrading the Compaq

Insight Management Agents

...

Summary

..............................

MigratingtoMicrosoftWindowsNTServer

4.0 on Compaq Servers

The information presented in this White Paper provides guidelines and requirements to

migrate Compaq Servers running Microsoft Windows NT Server Version 3.51 to

Microsoft Windows NT Server Version 4.0. This document presumes that you have a

thorough knowledge of Compaq Server products and the Microsoft Windows NT

operating system.

This White Paper includes information on:

•

New features and enhancements for Windows NT Server 4.0

•

Migration considerations

•

Four test migration scenarios

NOTE: Compaq highly recommends that you read this White Paper from cover-to-cover

BEFORE proceeding with the upgrade process.

WHITE PAPER (cont.)

467A/0197

NOTICE

The information in this publication is subject to change without notice.

COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE FOR TECHNICAL

OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN, NOR FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE

FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL.

This publication does not constitute an endorsement of the product or products that were tested.

The configuration or configurations tested or described may or may not be the only available

solution. This test is not a determination of product quality or correctness, nor does it ensure

compliance with any federal, state or local requirements. Compaq does not warrant products other

than its own strictly as stated in Compaq product warranties.

Product names mentioned herein may be trademarks and/or registered trademarks of their

respective companies.

Compaq, Contura, Deskpro, Fastart, Compaq Insight Manager, LTE, PageMarq, Systempro,

Systempro/LT, ProLiant, TwinTray, ROMPaq, LicensePaq, QVision, SLT, ProLinea, SmartStart,

NetFlex, DirectPlus, QuickFind, RemotePaq, BackPaq, TechPaq, SpeedPaq, QuickBack, PaqFax,

Presario, SilentCool, CompaqCare (design), Aero, SmartStation, MiniStation, and PaqRap,

registered United States Patent and Trademark Office.

Netelligent, Armada, Cruiser, Concerto, QuickChoice, ProSignia, Systempro/XL, Net1, LTE

Elite, Vocalyst, PageMate, SoftPaq, FirstPaq, SolutionPaq, EasyPoint, EZ Help, MaxLight,

MultiLock, QuickBlank, QuickLock, UltraView, Innovate logo, Wonder Tools logo in

black/white and color, and Compaq PC Card Solution logo are trademarks and/or service marks of

Compaq Computer Corporation.

Other product names mentioned herein may be trademarks and/or registered trademarks of their

respective companies.

Microsoft, Windows, Windows NT, Windows NT Server and Workstation, Microsoft SQL Server

for Windows NT are trademarks and/or registered trademarks of Microsoft Corporation.

Migrating to Microsoft Windows NT Server 4.0 on Compaq Servers

First Edition (January 1997)

Document Number 467A/0197

WHITE PAPER (cont.)

467A/0197

OVERVIEW

There are many reasons for migrating to Windows NT Server 4.0. Enhancements and new features

for Windows NT Server 4.0 provide an ideal platform to support file-and-print, application server,

and internet/intranet computing environments.

New features and enhancements include:

•• Better performance and ease-of-use in TCP/IP networks

• User interface more consistent with Microsoft Windows 95 and Windows NT Workstation 4.0

• Remote Boot (RIPL) support for diskless Windows and DOS clients

• Improved support for remote clients with Remote Access Services (RAS)

• Improved interoperability with NetWare servers through Gateway (and Client) Services for

NetWare

• Expanded support for graphics and multimedia

• Better networking and security management

• New application and file system support

• Expanded printing and font capabilities

• The Administrative wizards group the common server management tools into a single place

making it easier for an administrator to manage user accounts and other function.

• Microsoft Internet Information Server is included in the Windows NT Server 4.0 kit/license.

The Windows NT Server 4.0 operating system now provides better wide-area networking tools

and a powerful internet/intranet server platform. Refer to the Microsoft Windows NT Server 4.0

reference documentation for more detailed information.

NOTE: This White Paper does not cover upgrading from Windows NT Workstation 3.51 to

Windows NT Server 4.0.

WHITE PAPER (cont.)

467A/0197

WINDOWS NT FEATURES NOT AFFECTED BY THE MIGRATION

Windows NT Server 4.0 upgrade process uses the setting from the following features of Windows

NT Server 3.51 to ease the upgrade process:

• Local security accounts

• Custom settings in the registry

• Preferences set for administrative tools and accessories

• Network adapter settings

• Network protocol and service configuration settings

You are not required to perform any special preparation to maintain these features.

CONSIDERATIONS BEFORE MIGRATING

Before you begin the migration, decide what you want to accomplish and what method you want

to use. The method you choose affects the procedures you must perform to accomplish your goals.

No matter which method you choose, Compaq highly recommends that you backup your

system BEFORE you begin the upgrade process.

Compaq has identified some considerations that might affect your configuration and migration

method. These considerations are as follows:

• If you intend to keep a copy of Windows NT Server 3.51 on the server with Windows NT

Server 4.0, you must:

− Maintain the data integrity in current file systems and partitions.

− Completely backup your server.

This White Paper does not cover running dual versions of Windows NT on your server. However,

if you decide to maintain dual versions, Compaq recommends that you refer to the documentation

set provided with the Microsoft Windows NT Server 4.0 software.

• If your installation consists of domain controllers and multiple servers, you might need to

perform a sequence of upgrades. Microsoft recommends that you upgrade the Primary

Domain Controller (PDC) on a Windows NT Server 3.51 network to Windows NT Server 4.0

before upgrading the Backup Domain Controller(s) (BDC). If you upgrade a server that is not

the PDC first, all the new security information installed for Windows NT Server 4.0 is

replaced when the server restarts. The server automatically replicates all information from the

Windows NT Server 3.51 Domain controller. You can eliminate this problem by first

upgrading the Primary Domain Controller.

• If you are upgrading without Compaq SmartStart, you must install the Compaq Support

Software, (which updates or installs Compaq device drivers and support software) after

installing the Windows NT Server 4.0 operating system.

WHITE PAPER (cont.)

467A/0197

COMPAQ MIGRATION SCENARIOS

Compaq tested four migration scenarios. Each migration scenario was performed as an in-place

upgrade. The Windows NT Server 4.0 replaces the Windows NT Server 3.51 operating system.

Details on the migration configuration are located before the text describing the scenarios.

NOTE: If you want to maintain dual installations, Compaq recommends that you refer to

the documentation set provided with the Windows NT Server 4.0 software.

OUTLINE OF THE MIGRATION PROCESS

The following list contains the basic tasks involved in the migration process:

• Backup the server

• Determine hard drive space requirements

• Obtain current Windows NT 3.51 support (SSD)

• Disable startup options /services

• Upgrade Windows NT Server

• Upgrade non-Microsoft drivers

• Re-install disabled options/services

• Install the SSD

• Re-install the Compaq Insight Manager Agents

• Install the Microsoft Service Pack

Backup the Server

Compaq highly recommends that you backup your server BEFORE you begin the

upgrade process.

Determine Hard Drive Space Requirements

The Windows NT Server 4.0 Setup program requires that you reserve temporary hard drive space

on the server to perform the upgrade from Windows NT 3.51. The amount of temporary space you

need depends on the Setup method you choose. Installing from a network requires more space

than installing from CD-ROM.

The following provides an estimate of the temporary hard drive space required by the Windows NT

Server 4.0 migration process using either installation method.

• Migrating Windows NT Server 4.0 source files from a network directory - Approximately

100 Megabytes

• Migrating using the Windows NT Server 4.0 installation CD from Microsoft - Approximately

10 Megabytes

NOTE: Windows NT Server 4.0 displays a warning message if the server does not have

sufficient hard drive space.

WHITE PAPER (cont.)

467A/0197

Disable Startup Settings

It is only necessary to make modifications to the device and/or service setting if any of the devices

or services mentioned in the following sections were previously installed or enabled.

NOTE: Disabling or enabling the startup services does NOT have a detrimental effect on

the upgrade process issues; the upgrade process can continue with all of the appropriate

services enabled.

Compaq recommends that you disable certain Service and Device Startup settings before beginning

a Windows NT Server 4.0 migration. This can reduce the number of warnings similar to the

following message from displaying during the installation process:

At least one service or driver failed during system startup. Use the Event Viewer

to examine the Event Log for details.

Disabling Insight Agents and SNMP Services

Follow these steps:

1. Select the Main Window.

2. Select the

Control Panel applet.

3. Open the Services applet. The following screen displays:

4. Highlight Insight Agents then select Startup.

The Services dialogue screen displays (shown on next page).

WHITE PAPER (cont.)

467A/0197

5. Change the “Startup Type” to Disabled. Select OK to accept the setting.

6. Select “Close” to exit the service applet.

If you previously installed the SNMP Service, it should also be disabled via the Control Panel

Services applets. To disable the SNMP Service, repeat steps 1-5, replacing Insights Agents

with SNMP Service in step #4.

Disabling Compaq ProLiant Storage System and Compaq Systems Management Services

Devices

You must disable the Compaq ProLiant Storage System setting before you upgrade to

Windows NT 4.0 to avoid Service Management errors.

1. Access the Windows NT Server Control Panel, then select Devices. The following screen

displays:

WHITE PAPER (cont.)

467A/0197

2. Highlight

Compaq ProLiant Storage System then select Startup. The Compaq SCSI Device

Monitor dialogue screen displays:

3. Change the “Startup Type” to Disabled. Select OK to accept the setting and select Yes to

confirm the selection.

NOTE: A message displays warning you that changing these settings might cause the

system to become unstable. Ignore the message and select

Yes

to continue.

4. To disable the Compaq Systems Management Service, repeat steps 1-3, replacing Compaq

ProLiant Storage System with Compaq Systems Management Service in step #2.

5. Select

Close to exit the Devices applet.

NOTE: If you plan on maintaining both versions of Windows NT on your server, do

not disable the Compaq SCSI Device Monitor. If a warning message displays after

the upgrade process is complete, select

to continue with the installation process.

You can return to the Event Viewer later to view the Event Log and make any

necessary modifications.

Compaq Software Support Diskette Installation Overview

Compaq recommends that you upgrade to the latest SSD version if your SSD version is earlier

than 1.18.

The following screen displays after you run Setup on the Compaq Software Support Diskettes:

WHITE PAPER (cont.)

467A/0197

Select the Express button, which installs or upgrades the appropriate drivers depending on your

hardware configuration.

The following screen is a sample display of the SSD Express selection. Select the update button

to continue the SSD installation or upgrade process.

WHITE PAPER (cont.)

467A/0197

Migration Scenario 1

Windows NT 4.0 Set-Up Method

The following steps describe the process and when upgrading from an installation of Windows

NT Server 3.51 CD from Compaq SmartStart (SSD 1.18B) on a Compaq ProLiant 5000 directly

from the Windows NT 4.0 CD-ROM.

TABLE 1

COMPAQ PROLIANT 5000 SERVER MIGRATION

SCENARIO 1 CONFIGURATION

System Processor(s) Four 166-MHz Pentium Pro

Memory 128 MB

Disk Controller Compaq SMART-2/P Controller

Drive Configuration Two 4-GB (RAID1)

Network Controller Compaq NetFlex-3 100 VG Controller

Operating System Compaq SmartStart Windows NT Server 3.51, Windows NT Server 4.0

Software Windows NT SSD, version 1.19 and Compaq Insight Management Agents, version 3.10 or later

1. Backup your server completely, including the Registry.

2. Obtain the latest Compaq Support Software Disk (SSD 1.20 or higher). Obtain the latest

SmartStart CD to obtain the latest Compaq Support utilities or consult the Compaq Web site

(www.compaq.com).

If you previously installed SNMP Service, disable it. See pages 6 - 7.

If you previously installed the Compaq Insight Manager Agents, disable them. See

pages 6 - 7.

If you currently have the Compaq ProLiant Storage System installed, disable it. See

pages 7 - 8.

3. You can choose from the following Windows NT 4.0 installation methods:

− Direct CD-ROM install

− Boot-up floppies

NOTE: This scenario used the direct CD-ROM method.

4. Insert the Windows NT 4.0 CD into the CD-ROM drive.

a) From the file manager, select the drive letter that represents the CD-ROM drive.

b) Change to the i386 directory. Select File then select Run from the menu.

c) Type:

winnt32 /b (To create boot floppies, you would type winnt32 /ox in the same

i386 directory.)

Andere Handbücher für 117755-003 - ProSignia - 740

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Compaq Desktop Handbücher

Compaq

Compaq DESKPRO 1000 Bedienungsanleitung

Compaq

Compaq Deskpro 4000 Gebrauchs- und Pflegehandbuch

Compaq

Compaq Presario SR1700 - Desktop PC Bedienungsanleitung

Compaq

Compaq Compaq dx2290 Einrichtungshandbuch

Compaq

Compaq Presario CQ3300 - Desktop PC Bedienungsanleitung

Compaq

Compaq Deskpro EN Series Bedienungsanleitung

Compaq

Compaq Presario 5000 Series Handbuch

Compaq

Compaq Presario SR1602HM Bedienungsanleitung

Compaq

Compaq Compaq Pro 4300 Einrichtungshandbuch

Compaq

Compaq Compaq dx2390 Microtower Kurzanleitung

Compaq

Compaq Presario 5070 Handbuch

Compaq

Compaq dc7700 - Convertible Minitower PC Bedienungsanleitung

Compaq

Compaq Presario 6500 - Desktop PC Bedienungsanleitung

Compaq

Compaq Professional sp750 Installationsanleitung

Compaq

Compaq BL10e - HP ProLiant - 512 MB RAM Technisches Handbuch

Compaq

Compaq Evo D510 - Convertible Minitower Handbuch

Compaq

Compaq 3000R - ProLiant - 128 MB RAM Bedienungsanleitung

Compaq

Compaq dc7800 - Convertible Minitower PC Einrichtungshandbuch

Compaq

Compaq Deskpro 386 - Desktop PC Handbuch

Compaq

Compaq Presario SR1600 - Desktop PC Bedienungsanleitung

Compaq

Compaq Presario SR5700 - Desktop PC Anleitung zur Verwendung

Compaq

Compaq 8000 - Elite Convertible Minitower PC Referenzhandbuch

Compaq

Compaq 3000R - ProLiant - 128 MB RAM Kurzanleitung

Compaq

Compaq Deskpro AP500 Handbuch

Beliebte Desktop Handbücher anderer Marken

HP m9060n - Pavilion - Elite Technisches Datenblatt

Asus

Asus E210 Series Bedienungsanleitung

Dell

Dell Inspiron 600m Bedienungsanleitung

Dell

Dell Inspiron 3662 Bedienungsanleitung

TotalFlow

TotalFlow uFLO Bedienungsanleitung

HP Presario SV7000 - Desktop PC Bedienungsanleitung

HP ProDesk 400 G5 Handbuch

Logitech

Logitech MK320 Bedienungsanleitung

Dell

Dell XPS 730 H2C Bedienungsanleitung

Sony

Sony Vaio Series Bedienungsanleitung

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Bedienungsanleitung

Alto

Alto MD 250 Bedienungsanleitung

Lenovo

Lenovo ThinkCentre Edge 72 Handbuch

Lenovo

Lenovo ThinkStation D20 Handbuch

Arbor Technology

Arbor Technology FPC-7800 Series Bedienungsanleitung

Sony

Sony VAIO VGX-TP1 Series Bedienungsanleitung

Asus

Asus Eee Box B204 Bedienungsanleitung

Dell

Dell Optiplex 9010 All In One Bedienungsanleitung