Compaq QVision Graphics System Bedienungsanleitung
QVision Operations and Installation Guide
NOTICE
The information in this guide is subject to change without notice.
COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE FOR
TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED
HEREIN; NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM THE FURNISHING, PER FORMANCE, OR USE OF
THIS MATERIAL.
This guide contains information protected by copyright. No part of this guide
may be photocopied or reproduced in any form without prior written consent
from Compaq Computer Corporation.
®1992 Compaq Computer Corporation.
All rights reserved. Printed in the U.S.A.
COMPAQ, DESKPRO, SYSTEMPRO, LTE, FASTART
Registered U. S. Patent and Trademark Office.
SLT, EZ help and QVision are registered trademarks of Compaq Computer Corporation.
The software described in this guide is furnished under a license agreement or
nondisclosure agreement. The software may be used or copied only in
accordance with the terms of the agreement.
Product names mentioned herein may be trademarks and/or registered
trademarks of their respective companies.
QVISION GRAPHICS SYSTEM FROM COMPAQ
INSTALLATION AND OPERATIONS GUIDE
First Edition (February 1992)
Second Edition (April 1992)
Text Number 133577-002
Compaq Computer Corporation
QVision Operations and Installation Guide v, vi
FEDERAL COMMUNICATIONS COMMISSION NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
§Reorient or relocate the receiving antenna.
§Increase the separation between the equipment and receiver.
§Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
§Consult the dealer or an experienced radio or television technician for help.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this
device that are not expressly approved by Compaq Computer Corporation may void the
user's authority to operate the equipment.
Cables
Connections to this device must be made with shielded cables with metallic RFI/EMI
connector hoods to maintain compliance with FCC Rules and Regulations.
CANADIAN NOTICE
This equipment does not exceed the Class B limits for radiated emissions as described in
the Radio Interference Regulations of the Canadian Department of Communications.
GERMAN NOTICE
COMPAQ computers, when tested with the COMPAQ High-Resolution, Multi-Scanning
Color Monitor, were evaluated for compliance to the requirements of ZH1/618 in the
Text Mode (640 x 480) using MS-DOS Version 3.31 (or higher) and BASICA as
published by COMPAQ.
QVision Operations and Installation Guide vii, viii
CONTENTS
Chapter 1
INTRODUCTION
Product Features 1-2
Chapter 2
STARTING UP
Unpacking the Monitor 2-1
Connecting the Monitor to a Computer 2-2
Operating the Monitor 2-6
Pre-Set Modes 2-6
User-Modes 2-6
Storing Modes 2-7
Controls and Indicators 2-8
Chapter 3
CARE AND MAINTENANCE
Protecting the Monitor 3-1
Cleaning the Monitor 3-2
Shipping the Monitor 3-2
Servicing the Monitor 3-3
Troubleshooting 3-4
Appendix A
SPECIFICATIONS
Acceptable Signal Transmission Schemes A-2
Appendix B
NATIONAL POWER CORD SET REQUIREMENTS
U.S. and Canada B-1
Other Countries B-2
Appendix C
ELECTROSTATIC DISCHARGE
Preventing Electrostatic Discharge C-1
Methods of Grounding C-2
QVision Operations and Installation Guide 1-1
Chapter 1
INTRODUCTION
The QVision Graphics System from Compaq is designed for easy
installation and operation. To assist you while operating your monitor,
this guide contains the following information:
Chapter 1 Provides an introduction to the QVision Graphics System
from Compaq.
Chapter 2 Provides instructions for unpacking the monitor and
connecting it to a COMPAQ personal computer.
A description of the operating controls has also been
provided.
Chapter 3 Provides instructions for the care and maintenance of the
monitor. This chapter also contains a troubleshooting guide.
QVision Graphics System from Compaq
QVision Operations and Installation Guide 1-2
PRODUCT FEATURES
§The monitor has a 15- or 17-inch color tube, capable of displaying any
color palette resident in the graphics adapter or software application.
§The monitor is compatible with 31 to 58 kHz VGA-type and analog
adapters having refresh rates from 50 to 100 Hz.
§The monitor has multi-mode capability and stores the display size and
centering parameters for seven preset modes and six user-modes:
Pre-Set Modes
1024 x 768 at 72 Hz 1024 x 768 at 66 Hz
640 x 480 at 60 Hz 640 x 480 at 75 Hz
720 x 400 at 70 Hz 512 x 480 at 72 Hz
640 x 350 at 70 Hz
§The monitor is microprocessor based and can lock onto any scan
frequency from 31 kHz to 58 kHz horizontal and 50 Hz to 100 Hz
vertical.
§The monitor cable connects to any VGA 15-pin type COMPAQ-
compatible system. The monitor has 5 BNC inputs which, with the
use of other cables, allow it to be used with almost any type of
system. (See Appendix A.)
§The monitor complies with the recommended limits for electrostatic
field strength, magnetic field strengths (ELF and VLF) and electric
field strengths (ELF and VLF) when measured in accordance with
MPR 1990 test methods.
QVision Operations and Installation Guide 2-1
Chapter 2
STARTING UP
This chapter gives instructions for removing the monitor from its packing
material, connecting it to a COMPAQ personal computer, and using the
operating controls.
UNPACKING THE MONITOR
WARNING: The monitor weighs approximately forty-five
pounds. Use care when removing it from its packaging
material.
Never insert sharp instruments into the packing box while opening it.
The packing box contains the following items:
§The monitor
§The power cord
§The signal cable
§The QVision Graphics System from Compaq Installation and
Operations Guide.
Save the original container and packing material for possible future use.
QVision Operations and Installation Guide 2-2
CONNECTING THE MONITOR
TO A COMPUTER
To connect the monitor to your COMPAQ computer (or to any VGA-type
15-pin connector), follow these steps:
1. Locate the power switch on the lower right side of the monitor face.
Ensure that the power switch is in the OFF (O) position.
CAUTION: Electrostatic discharge (ESD) can damage
electronic components. Ensure that you are properly
grounded before beginning this procedure. See Appendix C
for ESD information.
Monitor Power Switch and Ventilation Slots
QVision Operations and Installation Guide 2-3
WARNING: To prevent possible damage to the video
graphic controller board, both the computer and monitor
must be OFF before connecting or disconnecting the signal
cable.
Power and Signal Cables
2. Place the monitor in a convenient, well-ventilated location near your
computer. The monitor cabinet has ventilation slots to prevent it from
overheating. Be sure nothing blocks these ventilation slots.
3. Connect the monitor contact end of the power cable to the connector
on the back of the monitor.
QVision Operations and Installation Guide 2-4
4. Connect the 5 BNC connectors from the signal cable to the monitor.
Push in and twist the connectors clockwise until they are locked into
place.
The BNC connectors are color-coded from left to right in the
following order:
White for horizontal sync (H)
Black for vertical sync (V)
Red (R)
Green (G)
Blue (B) for the video connectors.
Red, green, and blue represent the video connectors.
Connecting the 5 BNC Connectors to the Monitor
QVision Operations and Installation Guide 2-5
5. Connect the other end of the signal cable to the 15-pin video graphics
connector on the back of your computer.
Connecting the Graphic Signal Cable to the 15-Pin Connector
6. Secure the signal cable in place by tightening the screws on the
connector by hand.
7. Plug the AC contact end of the power cable into the AC outlet.
Inhaltsverzeichnis
Andere Compaq Monitor Handbücher
Compaq
Compaq COMPAQ Q1859 Bedienungsanleitung
Compaq
Compaq P900 Bedienungsanleitung
Compaq
Compaq Compaq S710 Bedienungsanleitung
Compaq
Compaq P1210 Bedienungsanleitung
Compaq
Compaq Flat Panel Monitor tft5017m Bedienungsanleitung
Compaq
Compaq TFT5000 Bedienungsanleitung
Compaq
Compaq TFT5010R Gebrauchsanweisung
Compaq
Compaq P1100 Bedienungsanleitung
Compaq
Compaq P1100 Bedienungsanleitung
Compaq
Compaq Compaq S710 Bedienungsanleitung
Compaq
Compaq CPQ-C1786FNSL Bedienungsanleitung
Compaq
Compaq Compaq M720 Bedienungsanleitung
Compaq
Compaq TFT8030 Bedienungsanleitung
Compaq
Compaq WF1907 - Compaq 19" LCD Monitor Anleitung zur Verwendung
Compaq
Compaq 8000 - Elite Convertible Minitower PC Bedienungsanleitung
Compaq
Compaq P700 Bedienungsanleitung
Compaq
Compaq TFT1701 Bedienungsanleitung
Compaq
Compaq W19Q Bedienungsanleitung
Compaq
Compaq V1100 Bedienungsanleitung
Compaq
Compaq TFT 5000R Bedienungsanleitung
