Compaq TFT8030 Bedienungsanleitung
User’s Guide
Compaq TFT8030 Flat Panel Monitor
Part Number: 237159-001
July 2001
Enhanced for accessibility
© 2001 Compaq Computer Corporation.
Compaq, the Compaq logo, Armada, Deskpro Registered in U. S. Patent
and Trademark Office.
Microsoft, MS-DOS, Windows, Windows NT are trademarks of Microsoft
Corporation in the United States and other countries.
All other product names mentioned herein may be trademarks of their
respective companies.
Compaq shall not be liable for technical or editorial errors or omissions
contained herein. The information in this document is provided “as is”
without warranty of any kind and is subject to change without notice. the
warranties for Compaq products are set forth in the express limited
warranty statements accompanying such products. Nothing herein should
be construed as constituting an additional warranty.
CAUTION: Text set off in this manner indicates that failure to
follow directions could result in damage to equipment or loss of
information.
WARNING: Text set off in this manner indicates that failure to
follow directions could result in bodily harm or loss of life.
Compaq TFT8030 Flat Panel Monitor Reference Guide
First Edition (July 2001)
Part Number: 237159-001
Product Features
The Compaq TFT8030 Flat Panel Display has an active
matrix, thin-film transistor (TFT), liquid crystal display
(LCD). The monitor features include the following:
■ Large 18.1-inch (45.9 cm) viewable area display.
■ 1280 × 1024 resolution, plus full-screen support for
lower resolutions.
■ Wide viewing angle to allow viewing from a sitting
or standing position, or moving side-to-side.
■ Tilt and swivel adjustment capabilities.
■ Removable base for flexible mounting solutions.
■ Dual video input channels with the following
connection options:
❏ Channel 1 supports either VGA analog or DVI-D
digital signals.
❏ Channel 2 supports either VGA analog, DVI-D
digital, Super Video or Composite Video signals.
■ Video input includes PiP (Picture in Picture) option
for windowed video display over data display.
■ VGA analog and DVI-Digital signal cables included.
■ Plug and play capability if supported by your system.
■ On-Screen Display (OSD) adjustments in six
different languages: English, Dutch, French, German,
Italian, and Spanish for ease of set-up and screen
optimization.
■ CD-ROM includes an information file (INF), Image
Color Matching file (ICM), Colorific calibration
software, the Compaq LCD Display Assistant setup
and configuration utility, the Compaq Display
LiteSaver utility, and product documentation.
■ Programmable sleep mode timer.
TFT8030 User’s Guide 1
■ Energy Saver feature for Energy Star compliance.
■ Security lock slot
■ AssetControl
■ Compliant with the following regulated
specifications:
❏ EPA ENERGY STAR
❏ European Union CE Directives
❏ Swedish MPR II 1990
❏ Swedish TCO '99
Information Files
The CD-ROM included with this monitor contains two
information files to be installed onto your computer; an
.INF file and an .ICM file.
■ The .INF file defines monitor resources and provides
specifications used by most operating systems to
install support software for certain hardware devices.
The .INF file ensures monitor compatibility and
optimization with your computer’s graphics adapter.
INF files are downloadable by clicking on:
www.compaq.com/products/monitors/index.html and
selecting the desired monitor.
■ The .ICM file provides color matching consistency
from monitor screen to printer and is activated from
within graphics programs that have this feature.
To install these files on your computer, insert the
Software and User’s Guide CD-ROM in your computer's
CD drive and when the CD-ROM menu launches, select
Install INF and ICM Files and follow the on-screen
instructions.
2 TFT8030 User’s Guide
Setting Up the Monitor
To set up the monitor, ensure that the power is turned off
to the monitor, computer system, and other attached
devices, then follow these steps:
This monitor has multiple connectors on the back panel
that can be used to connect two computers
simultaneously to the monitor. Be sure the Video
Channel Select button on the front of the monitor is set
to the correct position to receive signals from the
connected computer. See the Front Panel Controls table
for more information.
1. Place the monitor in a convenient, well-ventilated
location near your computer.
2. Connect the signal and AC power cables to the
monitor 1. Refer to the next section, “Connecting
the Signal Cables,” for additional information.
3. Connect the monitor signal cable 2to the
appropriate video connector on the rear panel of the
computer.
4. Connect the AC end of the power cable 3to AC
receptacle on the monitor.
5. Connect the power cable 4to an electrical wall outlet.
TFT8030 User’s Guide 3
WARNING: To reduce the risk of electric shock or damage to
your equipment:
■ Do not disable the power cord grounding plug. The grounding
plug is an important safety feature.
■ Plug the power cord into a grounded (earthed) electrical outlet
that is easily accessible at all times.
■ Disconnect power from the monitor by unplugging the power cord
from the electrical outlet.
■ Do not place anything on power cords or cables. Arrange them
so that no one may accidentally step on or trip over them. Do not
pull on a cord or cable. When unplugging from the electrical
outlet, grasp the cord by the plug.
For security purposes, this monitor has been fitted with a slot for
use with a security cable lock that can be purchased separately at
most computer stores.
4 TFT8030 User’s Guide
After you turn on the monitor, install the Compaq LCD Display
Assistant utility included on the CD-ROM. Use the on-screen
instructions to adjust the picture quality of your monitor. To
install this utility, follow the instructions on the “Configuring
Your Compaq LCD Monitor” card located in the Program
License Agreement packet.
Important: Always activate a screen saver program, the
programmable sleep timer, the Compaq Display LiteSaver
utility, or turn off the monitor when it is not in use for a
prolonged period of time. All LCD monitors that display the
same static image on screen for a prolonged period of time may
exhibit screen image retention. Note that image retention is not a
permanent condition and will fade over a period of time. Image
retention is a condition that may occur on all LCD screens.
Connecting the Video Signal Cables
To connect the VGA analog or DVI-D (Digital Visual Interface-
Digital) cable to the corresponding connector on the back of the
monitor, you must first remove the monitor base cover.
WARNING: Before beginning to disassemble the monitor, be sure
the monitor is turned off and the power and signal cables are both
disconnected.
The DVI-D cable supplied with this monitor is for digital- to-
digital connection only. Your computer must have a DVI-
compatible graphics card installed for use with this cable. When
connecting the DVI-D signal cable to the DVI connector on the
monitor, you must connect the other end of the DVI-D cable to
the DVI connector on the computer.
TFT8030 User’s Guide 5
1. Lay the front bezel down on a soft area to prevent it from
getting scratched, defaced, or broken.
2. Remove the cover plate from the monitor base by placing
your fingers in the opening on the bottom of the base and
pulling upward, then pulling out to remove the cover.
3. Remove the back panel from the monitor by pushing the
bottom tabs upward and pulling out to remove the panel.
4. Connect the video cable to the corresponding connector on
the back panel of the monitor 1by threading the cable
through the neck on the monitor base to the connector, then
connect the other end of the cable 2to the appropriate video
connector on the back panel of the computer.
5. Replace the monitor back panel and monitor base cover.
6. Reconnect the power cable and power on the monitor and
computer.
6 TFT8030 User’s Guide
The DVI-D connector on this monitor uses digital video
information to provide higher speed for higher display
resolution. The results are more precise video displays without
manually adjusting screen display quality.
Signal Cables Included:
■ VGA (Analog) to VGA Connector (15-pin)
■ DVI-D Cable (Digital only) to DVI Digital Connector
Signal Connectors and Cables
There are six signal input connectors: two VGA connectors, two
DVI-D connectors which support TMDS digital video signals,
and two video connectors which support NTSC, PAL, and
SECAM formats. The monitor will automatically select the two
connectors which will be displayed on the dual channel monitor
using the automatic input selection mode described in the “Initial
Select Switch” section. Alternately, the monitor defaults can be
overridden and Channel 1 or Channel 2 inputs selected using the
On-Screen Display (OSD).
TFT8030 Input Connectors
Video Channel Designator Connector Type
1 1-A VGA Analog
1-D DVI-Digital
2 2-A VGA Digital
2-D DVI-Digital
2-SV Super Video
2-CV Composite Video
TFT8030 User’s Guide 7
Input Select Switch
The Video Channel Select control is located at the left-hand side
of the lower front bezel. To the left and right of the Select
control are two indicators that display the video channel that is
selected. The left indicator is for Channel 1 and the right
indicator is for Channel 2.
The TFT8030 has three video detection modes described in the
following sections:
■ Automatic Input Selection (Monitor Default)
■ Input Recall
■ User Input Selection using the On Screen Display
Automatic Input Selection
This section describes the monitor’s input detection scheme at
the initial power-up or when the user has selected Auto Detect
using the OSD for both Channels 1 and 2.
If only one active video input is connected, the monitor
automatically enables and displays that input. If multiple video
inputs are connected to the monitor (either active or in the
energy saving sleep mode), the monitor detects and displays the
factory default video summarized below.
Channel 1 is assigned to the first valid video connection in the
following order:
■ Analog 1
■ Digital 1
Channel 2 is assigned to the first valid video connection in the
following order:
■ Analog 2
■ Digital 2
■ Super Video
■ Composite Video
8 TFT8030 User’s Guide
Inhaltsverzeichnis
Andere Compaq Monitor Handbücher
Compaq
Compaq W19Q Bedienungsanleitung
Compaq
Compaq Compaq Q2159 Bedienungsanleitung
Compaq
Compaq TFT5010 Bedienungsanleitung
Compaq
Compaq Compaq S710 Bedienungsanleitung
Compaq
Compaq WF1907 - Compaq 19" LCD Monitor Anleitung zur Verwendung
Compaq
Compaq TFT 5000R Bedienungsanleitung
Compaq
Compaq V50 Bedienungsanleitung
Compaq
Compaq S920 Gebrauchsanweisung
Compaq
Compaq V900 Gebrauchsanweisung
Compaq
Compaq P 110 Bedienungsanleitung
Compaq
Compaq V710 Bedienungsanleitung
Compaq
Compaq TFT5030 Bedienungsanleitung
Compaq
Compaq P1100 Bedienungsanleitung
Compaq
Compaq P700 Bedienungsanleitung
Compaq
Compaq TFT5010R Gebrauchsanweisung
Compaq
Compaq TFT 1501 Bedienungsanleitung
Compaq
Compaq V55 Bedienungsanleitung
Compaq
Compaq Compaq S710 Bedienungsanleitung
Compaq
Compaq 7020 Bedienungsanleitung
Compaq
Compaq Compaq M720 Bedienungsanleitung
