COMPX elock Bedienungsanleitung
1
CompX eLock®is a highly engineered lock with a motor-driven latch. Its uncompromising lock
control electronics include a non-volatile memory that stores 250 user / supervisor codes and
audit trail. With optional LockView®audit trail software, CompX eLock®remembers 1500 access
attempts. Programming is simple with numeric keypad or WindowsTM based LockView®software.
Quick Programming Guide
1. GETTING STARTED:
a. The unit is shipped with no user / supervisor codes
b. Press and hold until the beeping stops
c. Input the new PIN (4 digit min) and press or present new card
d. This PIN / Card is now a supervisor in slot #001
2. ADD A USER:
a. Input a valid supervisor PIN and press or present valid supervisor card
b. Press and hold until beeping stops
c. Input the new user PIN (4 digit min) and press or present new card
3. ADD A SUPERVISOR:
a. Input a valid supervisor PIN and press or present valid supervisor card
b. Press and hold until beeping stops
c. Press and hold again until beeping stops
d. Input new supervisor PIN (4 digit min) and press or present NEW supervisor card
4. DELETE A USER OR SUPERVISOR:
a. Input a valid supervisor PIN and press or present valid supervisor card
b. Press and hold until beeping stops
c. Input the PIN to be deleted and press or present existing card to be deleted
5. ADD A USER WITH A SPECIFIC SLOT ASSIGNMENT:
a. Input a valid supervisor PIN and press or present valid supervisor card
b. Press and hold until beeping stops
c. Enter slot number that will be assigned to user and press
(example: to program slot 6 type 006 )
d. Input the new user PIN (4 digit min) and press or present NEW card
6. DELETE A USER WITH A SPECIFIC SLOT ASSIGNMENT:
a. Input a valid supervisor PIN and press or present valid supervisor card
b. Press and hold until beeping stops
c. Enter slot number to be cleared and press (example: to clear slot 6 type 006 )
d. Enter slot number to be cleared again and press (example: to clear slot 6 type 006 )
See programming
guide included
with optional
LockView ®
software for
advanced
programming
instructions.
NUMERIC
KEYPAD
MAGSTRIPE
CARD
PROX
READER
PROX READER / KEYPAD
DUAL SYSTEM
MAGSTRIPE / KEYPAD
DUAL SYSTEM
Thank you for choosing eLock.
1
2
CompX eLock®Accessories
HID is a trademark of HID Corporation. * These items are offered as Service / Replacement Parts only.
AC ADAPTER
Part Numbers:
EL-2004-9VWB
(for use with the CompX eLock kit)
EL-2004-acWB
(for use with 12V electric strikes)
SUPERVISOR
HID®PROX USER,
SUPERVISOR CARD
Part Number:
EL-2004-Pc (no logo)
EL-2004-Pc-S (CSP logo)
LOCKVIEW®
SOFTWARE KIT
(provided with 7ft., 6-pin RJ11 cable,
1-USB dongle, 1 LockView®CD)
Part Number:
EL-LockViEW-3
HID®PROX TAG
Part Number:
EL-2004-PT
MAGSTRIPE USER,
SUPERVISOR CARD
Part Number:
EL-2004-MSc (no logo)
EL-2004-MSc-S (CSP logo)
LATCH CABLE,
*24”
Part Number:
EL-2004-Lc
RJ 11 EXTENSION
KIT, 4”
Part Number:
EL-2004-RJ kiT
TORX HEAD
DRIVER FOR
FRIG KIT
(Torx head bit also available)
Part Number:
EL-dRV-15
LATCH SPLITTER
(for running up to 2 latches)
Part Number:
EL-2004-LS
MOTORIZED
LATCH*
Part Number:
EL-LaTch-3
3
TEMPLaTE on
oPPoSiTE PagE
4
1.81
7.77
NoTe:
Don't forget
to fill out and
return your
warraNTy
card!
CompX eLock®Surface Mounting
Use the diagrams below as a template for holes to be drilled and for mounting your CompX eLock®
.
Put this template on the outside of the cabinet door where the eLock will go, and you can drill right through
it to mount your CompX eLock®
. Mount with 2 shorter, steel colored screws.
#1a
#2
#3
#4
#5
#6
#1b
#1a, b Mounting Holes
required
#2 Battery Latch Cable
required
#3 Alarm
optional
#4 Battery Cable*
optional
#5 RJ11 Port
required only if using LockView
#6 AC Wall Adapter*
optional
* If you're using a battery
cable,then a wall adapter
is not required. If you're using
a wall adapter, then battery
cable is not required.
Hole Function
warNiNg:
Print this page and
measure the line
above. It is ONE
INCH LONG. If it
measures less than
or more than one
inch, the template
measurements also
need to be scaled
accordingly.
FaiLure To
do so couLd
resuLT iN
misdriLLed
hoLes.
1”
5
warNiNg: Print this
page and measure the line
above. It is ONE INCH
LONG. If it measures less
than or more than one inch,
the template measurements
also need to be scaled
accordingly.
FaiLure To do so
couLd resuLT iN
misdriLLed hoLes.
1”
CompX eLock®Latch Dimensions
LockView®Software
qAdd, edit, view and delete users / supervisors and their credentials
qAdd, edit and delete CompX eLocks®
qAssign access rights between users / supervisors and CompX eLocks®in the database
qUSB connection required
qDownload, view, save, print, archive and delete audit trails
qDual credential access available
qSet real time clock
qTime based access restrictions
qCreate user groups
qWindowsTM based
LockView is a Registered Trademark of CompX International. Windows is a trademark
of the Microsoft Corporation. Specifications may vary based on user application.
Use the diagrams below as a template for holes to be drilled and for mounting your
CompX eLock®latch. Put this template on the inside of the cabinet door where the latch
will go, and you can drill right through it to mount your CompX eLock®latch.
Mount with 4 longer, black colored screws.
6
TEMPLaTE on
oPPoSiTE PagE
7
2d bar code. Provides the same information as sticker
number three, but a 2d laser scanner is needed to
decode the information.
1d bar code. Place this sticker on or around the CompX
eLock® unit to help identify which codes to use if
resetting the lock is necessary.
Keep this sticker in a safe location.
Serial #: Needed to identify CompX eLock® units
Passcode: Unique to lock. Needed for LockView.
Prevents unauthorized LockView use
User Rst: Allows administrator or owner to erase
all user codes from eLock unit but keep
supervisor codes
Fact Rst: Erases all codes from eLock, including
settings. eLock unit will need to be set
up again after a Factory Reset
Sticker #1
Sticker #2
Sticker #3
sample
sample
sample
CompX eLock®Warranty Card
These stickers are included with each CompX eLock® unit. Please review the information and keep the stickers in a
safe location as they may be needed to reset or identify a specific eLock unit. The codes shown here are not real codes.
They are representations of what the stickers will look like.
8
sample
Copyright © 2009 CompX Security ProductsPart #: 331926-0000-00
864.297.6655
compxelock.com
PO Box 200
Mauldin, SC 29662
CompX eLock®Warranty Card
NoTe:
Don't forget
to fill out and
return your
warraNTy
card!
sample
Sticker
#3
Affix one copy of sticker #3
(see page 7) to the CompX
eLock® registration card
and return to CompX Fort
at address shown on the
registration card.
Revised 11.2.09
Andere Handbücher für elock
2
Andere COMPX Sperren Handbücher
COMPX
COMPX Stock Locks C8054 Leitfaden
COMPX
COMPX Stock Locks C1975 Leitfaden
COMPX
COMPX TS1058BD Leitfaden
COMPX
COMPX SD990 Leitfaden
COMPX
COMPX Timberline CB-234 Bedienungsanleitung
COMPX
COMPX Timberline CB-291 Bedienungsanleitung
COMPX
COMPX CB084-184 Bedienungsanleitung
COMPX
COMPX 1T-058 Betriebsanleitung
COMPX
COMPX MFW-1118 Leitfaden
COMPX
COMPX C8422 Leitfaden
COMPX
COMPX TuBAR Retrofit for Dresser WayneVista 2 & 3 CAT... Bedienungsanleitung
COMPX
COMPX Timberline CB-294 Bedienungsanleitung
COMPX
COMPX Timberline CB-242 Bedienungsanleitung
COMPX
COMPX QUIKCOVER Bedienungsanleitung
COMPX
COMPX FORT MFW-1038 Bedienungsanleitung
COMPX
COMPX YPT-1010 Leitfaden
COMPX
COMPX Timberline CB-281 Bedienungsanleitung
COMPX
COMPX eLock 150 Series Bedienungsanleitung
COMPX
COMPX C8188 Leitfaden
COMPX
COMPX Timberline CB-235 Bedienungsanleitung
Beliebte Sperren Handbücher anderer Marken
ELCOM
ELCOM 7205 Bedienungsanleitung
Stealth SAFES
Stealth SAFES ShadowVault Bedienungsanleitung
Knox
Knox KeySecure 5 Bedienungsanleitung
Kwikset
Kwikset 48334/01 Bedienungsanleitung
Metra Electronics
Metra Electronics Door Access Terminal Combo Bedienungsanleitung
Kilitronik
Kilitronik miniK10m Bedienungsanleitung