ComSonics PON-3 Bedienungsanleitung

User's Guide to the PON-3

PON Power Meter

PON-3 English Version

User's Guide to the PON-3

PON Power Meter

CONTENTS PAGE

Introduction

1.1 Summary

1.2 Main Function and Specifications

1.3 Specification

2 Warranty

3 Safety Information

3.1 Discharged batteries

3.2 AC operation

4 Preparing for Operation

5 Operation

5.1 Layout

5.2 Key’s Functions

5.3 Definitions

5.4 Quick Operation

5.5 Detail Operation

5.5.1 Powering On the Instrument

5.5.2 Test mode switch

5.5.3 Threshold Setup

5.5.4 Time Setup

5.5.5 Unit Switch

5.5.6 Reference Value Setup

5.5.7 Backlit Setup

5.5.8 Description of Memory Record Function

6 Remarks

7 Recommendations

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

PON-3 / Introduction

1. Introduction

10-03-03 11: 43:15

1.20

-4.50

-15.00

PO N-3

PON-3 is a portable, high quality PON optical power meter. It is

specifically designed to meet the rapid growth of the FTTx market

with PON (Passive Optical Network) technologies. It is capable of

measuring all three signals (1310nm, 1490nm and 1550nm) that

carry voice, data and video in a single fiber. The PON-3 can

measure not only 1490nm and 1550nm optical signal, but also

accurately detect and measure the upstream burst at 1310nm sent

from an ONU while the ONU is in the idle mode. The simple

operation and accurate measurements make the PON-3 an ideal tool

for PON suitable for APON, BPON, EPON and GPON applications,

installation/acceptance tests to ensure that they meet required

standards, and service activation/ troubleshooting.

PON-3 / Introduction

1.1 Main Functions and Specifications

Cost efficient and palm sized - designed for field testing

Supports Pass/Fail measurements with visible indicators

Easy-to-use interface with a large color TFT display and LED indicators for easy visibility.

Simply connect-and-display the results for all three wavelengths: 1310/1490/1550nm

Detect and measure the1310 nm upstream burst

Supports APON, BPON, EPON and GPON networks

Pass, Fail and Warning indicators

User definable threshold value (up to 10 presets)

Auto power shut off

Low battery warning

USB interface

Real-time clock

Ni-MH battery for more than 20 hours continuously on-time or AC/DC adapter

PON-3 / Specification

1.2 Specifications:

Connector Type

FC/PC SC/PC (ST/PC optional)

Measurement Range

(Continuous Data stream)

1310nm

1490nm

1550nm

-40dBm~+10dBm

-40dBm~+20dBm

Burst measurement range

(1310nm bursted signal)

-30dBm~+10dBm

Spectral Passband

1310nm

1490nm

1550nm

1260nm~1360nm

1480nm~1550nm

1539nm~1565nm

Insertion Loss

1.5dB

Accuracy

±0.5dB

Linearity

±0.2dB

Data Storage

1000Sets

Display

2.8 inch TFT LCD

Refresh Rate of Display

2.5Hz

Threshold

10 sets(configured via PC-based software)

Auto Power-off

Yes

Number of Ports

2 (1 for ONU,1 for OLT &.Video)

Operating Temperature

-10 to +50°C

Relative Humidity

0%~95%,non-condensing

Power Supply

1.2V*4pcs Ni-MHAA;12V AC/DC Adapter

Battery life

>20 hours

Dimension

190mm*105mm*55mm(L*W*H)

Net Weight

700g

NOTE: 1 Valid at 1550nm,CW,23±3°C,Relative Humidity≤70%,with an FC connector.

PON-3 / Warranty

2. Warranty

One Year Limited Warranty

ComSonics products are warranted against the defective components and workmanship for a

period of one year from the date of delivery to the original customer. Any product found to be

defective within the warranty period can be returned to a ComSonics authorized service center for

repair, replacement and calibration.

Exclusions

The warranty on your equipment shall not apply to defects resulting from the following:

Unauthorized repair or modification

Misuse, negligence, or accidents

PON-3 / Safety Information

3. Safety Information

Warnings!

Never look directly into optical outputs or a fiber while the equipment is ON. Invisible laser light will

cause permanent damage to your eyes.

Do not short-circuit the terminal of AC adapter / charger and the batteries. Excessive electrical

current may cause personal injury due to fumes, electric shock, or equipment damage.

Connect AC power cord with the equipment and wall socket properly. While inserting the AC plug,

make sure there is no dust or dirt on the terminals and both plugs are fully seated. Incomplete

engagement may cause fuming, electric shock or equipment damage and may result in personal

injury.

Do not operate the equipment near hot objects, in hot environments, in dusty/ humid conditions, or

when condensation is present on the equipment. This may result in electric shock, product malfunction,

or poor performance.

PON-3 / Discharged batteries

3.1 Discharged batteries

Remarks:

1) When the battery power is low, the warning indicator will blink. Replace the batteries or charge the

batteries using the AC adapter.

2) Please make sure that you have turned the instrument OFF before charging the batteries, unplug the AC

adapter when the batteries are fully charged.

3) Please make sure the batteries are correctly placed in the device before charging them.

4) To eliminate the possibility of battery acid leakage, please take out the batteries if the unit will not be used

for a long time.

PON-3 / AC Operation

3.2 AC operation

If the instrument is mainly used at one location, e.g. in a laboratory or test department, the AC adapter can be

used for power instead of batteries. There is a 12V DC input jack on the left side of the PON-3 device. When the

AC adapter is plugged in, the AC Indicator on the LCD will be displayed.

Note:

1 Power is supplied by the AC adapter even if the batteries are installed. The battery indicator will not be

displayed on the screen when AC adapter is plugged.

2 Make sure that the operating voltage of the AC Adapter / Charger is the same as the local AC line

voltage.

Inhaltsverzeichnis

Andere ComSonics Messgerät Handbücher

ComSonics

ComSonics QAM Sniffer III Bedienungsanleitung

ComSonics

ComSonics Companion Bedienungsanleitung

ComSonics

ComSonics Sniffer Shadow Bedienungsanleitung

ComSonics

ComSonics CyberTek QUALIFIER Bedienungsanleitung

ComSonics

ComSonics Qualifier X-Ray Bedienungsanleitung

ComSonics

ComSonics QAM Sniffer Bedienungsanleitung

ComSonics

ComSonics QAM Shadow Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung