Conmec CT436E Bedienungsanleitung
Operator's Manual
Electrical Walk-behind
Power Trowel
CT436E
2
Manufacturer Conmec Engineering Co., Ltd
No.88, 2# Industrial Avenue, An Wu Road,
Wu Qiao County, Feng Xian, Shanghai, P.R.C
Tel: 86 (0)21 57407318 Fax: 86 (0)21 57406955
www.conmec.cn
Original instructions This Operator’s Manual presents the original instructions. The original
language of the Operator’s Manual is English.
3
Foreword
This manual contains important instructions for this machine. These instructions must be followed
during installation, operation, and maintenance of the machines.
This manual provides information and procedures to safely operate. For your own safety and to
reduce the risk of injury, carefully read, understand, and observe all instructions described in this
manual.
We reserves the right to change any of the contents in this manual without notice.
Warranty
Our products are covered by warranty for a period of twelve (12) months from the date of purchase
against defects in material or workmanship provided that:
The product concerned has been operated and maintained in accordance with the operating
instructions.
Has not been damaged by accident, misuse or abuse.
Has not been tampered with or repaired by any unauthorized person.
Any evidence of failure to meet these conditions may result in a denial of the warranty claim.
The owner is responsible for the cost of transportation to and from the authorized repairer and the
unit is at the owners risk while in transit to and from the repairer.
Impact damage is not covered under warranty. Clutches are not covered under any warranty.
Engines are officially guaranteed by engine manufacturer. Please refer to the annex for engine
warranty.
4
Table of Contents
Foreword 3
Warranty 3
1. TECHNICAL DATA 17
1.1 Technical Specification…………………………………………………………………………….17
1.2 Dimension …………………………………………………………………………….……………18
2. SAFETY INFORMATION 5
2.1 Machine Description and Intended Use ………………………………………………….5
2.2 Operating Safety………………………………………………………………………….....5
2.3 Safety regarding operation of machine………..........................…………………..…..6-7
2.4 Electrical safety.............................................................................................................7
2.5 Service Safety ……………………………………………………………………………….7
2.6 Safety regarding maintenance.....................................................................................8
2.7 Label Locations………………………………………………………………………………8
2.8 Labels Meaning …………….……………………………….…………………………….9-10
3. OPERATION 11
3.1 Preparing the Machine for First Use ………………………………………………..………..10
3.2 Controls ………………………..………………………………………………………………….10
3.3 Installing the Blades ………………………………..……………………………….…….…….11
3.4 Before Starting ……………………………………………………..………………….…………..11
3.5 Handle Installation and Adjusting ……………….……………..…………………….………..12
3.6 Safety Stop Switch ………………………………………………………………………………12
3.7 To Start …………………………………………………………………………………………….12
3.8 To Stop ……………………………………………………………….………………..…………..13
3.9 Speed Control .....................................................................................................................13
3.10 Pitch Adjustment ………………………………………………………………….……..…....13
3.11 Floating Operation……………………………………………………………….………. ..13
3.12 Finishing Operation………………………………………………………..……………….13
4. ELECTRICAL SCHEMATIC 14
5. MAITENANCE 15
5.1 Periodic Maintenance Schedule………………………………………..………………..…15
5.2 Battery Maintenance.....................................................................................................15
5.3 Directions for Battery charger........................................................................................15
5.4 Lubrication…………………………………………………………………………..…..…….16
5.5 Lifting Trowels…………............................……………………………………….…......……....16
5.6 Trouble Shooting …………………………………………………..………….…….…………….17
6. MACHINE ACCESSORIES 17
EC Declaration of Conformity 18
5
1. Specification
The power trowel with battery is available in operated with rechargeable battery pack.
To find the specifications that apply to your machine, check the information plate on the
machine.
1.1 Technical Specification:
Model
CT436E
Motor type
DC60V
Motor speed
r/min
4000
Power
kw
1.2
Operating weight (wo battery)
kg
94
Blade speed
rpm
0-140
Rotor Dia.
cm(in)
92(36)
Finishing Blade
in
6x14
Combination Blade
in
8x14
Float Pan
in
37
Battery: 60V/52AH (Optional)
Battery weight: 18kg
1.2 Dimension (L X W X H) : 1740mm*975mm*881mm
6
2. SAFETY INFORMATION
2.1 Machine Description and Intended Use
This machine is a walk-behind concrete finishing trowel. It consists of a engine mounted frame,
a electrical motor, a battery pack, a gearbox, a guard ring and a handle.
This machine is intended to be used for floating and burnishing curing concrete.
2.2 Operating Safety
Only trained personnel are permitted to start, operate, and shut down the machine.
They have received instruction on how to properly use the machine and are familiar
with required safety devices.
Read, understand, and follow procedures in the Operator’s Manual before attempting
to operate the machine.
The machine must not be accessed or operated by children and people impaired by
alcohol or drugs.
NEVER operate this machine in application for which it is not intended.
NEVER allow anyone to operate this equipment without proper training. People
operating this equipment must be familiar with the risks and hazards associated with it.
Do not allow anyone to stank or lean on the unit during operation.
ALWAYS Keep the safety stop switch system in adjustment and good operating
condition at all times. Do not operate the trowel if it does not work properly. Out of
control Trowels can cause serious personal injury and damage to fresh concrete
surfaces. This system will automatically stop the unit if the operator loses control of it
during operation.
ALWAYS make sure the safety stop switch is disengaged (lever in the down position)
before starting the unit. Keep one hand firmly on the handle while starting and do not let
go of the handle during operation.
ALWAYS wear protective clothing, safety glassed, hearing protection, safety-toed
footwear to the job site while operating the machine.
ALWAYS store the machine properly when it is not being used. The machine should be
stored in a clean, dry location out of the reach of children.
2.3 Safety regarding operation of machine
Recognized official procedures have to be used to ensure the machine is operated in
safe and best conditions.
Only operate the machine when all safety devices and related safety equipment are
present and operational!
Check the machine visually for any damage and defects at least once a day.
In the event of operational malfunctions the machine must be shut down immediately
and secured!
Secure the work area around the machine in public areas providing a safety distance of
at least 10 m (3.3 ft) from the machine.
7
Faults must be immediately rectified.
Carry out the switch on, and switch off operations in accordance with this user guide.
Before switching on the machine make sure that no-one can be endangered when the
machine starts up.
Never operate the machine when it’s in its upright position.
All persons in the proximity of the machine must wear ear and eye protection as well as
safety shoes. In addition the machine operator must wear close-fitting protective
clothing.
Make sure there is no debris in the work area.
Check the work area for screws or other hard objects in the concrete. Don’t use the
machine if there are any foreign objects stuck into the surface. Such objects must be
removed prior to operation of machine
2.4 Electrical safety
Work on electrical equipment may only be undertaken by a skilled electrician or by
trained persons under the supervision of a skilled electrician as well as in accordance
with the local electrical engineering regulations.
The electrical equipment for the plant must be inspected regularly. Defects must be
rectified immediately. Call a skilled electrician or out customer services.
A second person must be in attendance whilst the electrical engineer is working on the
equipment.
The work area must be secured against any third party entering the work area. Follow
local electrical engineering regulations while working on the machine. Never leave a
machine unattended. Use only tools that are insulated against electricity.
Only start work after you are familiar with the electrical engineering regulations that
apply to the local area.
2.5 Service Safety
Read and understand the instructions contained in the manual delivered with the
machine before servicing or maintaining
Familiarize yourself with the location and proper use of all controls and safety devices
before servicing or maintaining.
Contact local dealer for additional training if necessary.
Do not allow improperly trained people to service or maintain the machine. Personnel
servicing or maintaining the machine must be familiar with the associated potential
risks and hazards.
Do not attempt to clean or service the machine while it is running. Rotating parts can
cause severe injury.
Do not remove blades while the machine is hanging overhead.
Disconnect the spark plug on machines equipped with gasoline engines, before
servicing, to avoid accidental start-up.
When replacement parts are required for this machine, use only our replacement parts
or those parts equivalent to the original in all types of specifications, such as physical
dimensions, type, strength, and material.
8
2.6 Safety regarding maintenance
Set the machine into the OFF position before beginning any work on the machine.
Never work on the machine while power is still connected!
All parts must have come to a complete stop before beginning any work!
Adjustment, servicing and inspection work on the period of time limits, specified in this
User Guide as well as any information on the replacement or parts and equipment must
be undertaken and/or complied with!
These activities may only be undertaken by qualified personnel.
The machine must not be connected to any power source while cleaning.
2.7 Label Location
9
2.8 Label Meanings
Our machines use international pictorial labels where needed. These labels are described
below:
Label
Meaning
WARNING!
Cutting hazard. Always replace blade guard!
`
CAUTION!
Read and understand the supplied Operator’s
Manual before operating the machine. Failure to
do so increase the risk of injury to yourself or
others.
WARNING!
Always wear hearing and eye protection when
operating this machine.
A nameplate listing the model number and serial
number is attached to each unit. Please record
the information found on this plate so it will be
available if the nameplate lost or damaged.
When requesting service information, the serial
number should be specified of the unit.
10
3. OPERATION
3.1 Preparing the Machine for First Use
3.1.1 Make sure all loose packaging materials have been removed from the machine.
3.1.2 Check the machine and its components for damage. If there is visible damage, do not
operate the machine! Contact dealer immediately for assistance.
3.1.3 Take inventory of all items included with the machine and verify that all loose components
and fasteners are accounted for.
3.1.4 Add fluids as needed and applicable, including fuel, engine oil, and battery acid.
3.1.5 Make sure there is no debris in the work area.
3.1.6 Check the work area for screws or other hard objects in the concrete. Don’t use the machine
if there are any foreign objects stuck out from the surface. Before operate the machine such
objects must be removed.
3.2 Controls
Ref. No.
Description
Ref. No.
Description
1
Power Indicator
2
Power (Key Switch)
3
Speed control on Auto
4
Manual/Auto for Speed Control
5
Safety stop switch
6
Speed Control on Manual
7
Display Screen
Inhaltsverzeichnis
Andere Conmec Baumaschinen Handbücher
