Cooper Lighting IMI-597 Bedienungsanleitung

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible

contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please

contact your nearest representative.

1. Open the Door -

Press both BUTTON LATCHES at the same time and open the door.

See Figure 1.

2. Reflector Removal -

Press the two REFLECTOR TABS outward and

swing the REFLECTOR down.

See Figure 2a and Figure 2b.

NOTE: Disconnect REFLECTOR CONNECTOR from

the HOUSING as shown in Figure 2c.

Customer First Center • 1121 Hwy 74 South • Peachtree City, GA 30269 IMI-597 AVU040197

Flite

Sheet 1 of 8

8/31/04 IMI-597

INSTALLATION INSTRUCTIONS

IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE.

RETAIN FOR FUTURE REFERENCE.

General: Upon receipt of fixture thoroughly inspect for any

freight damage, which should be brought to the attention of

the delivery carrier. Compare the catalog description listed

on the packing slip with the fixture label on the housing to

assure you have received the correct merchandise.

Safety: This fixture must be wired in accordance with

the national electrical code and applicable local codes

and ordinance. Proper grounding is required to insure

personal safety. Carefully observe grounding procedure.

All work should be done by an electrician.

WARNING: Risk of Electric Shock. Disconnect power at circuit breaker panel or

fuse box before installing or servicing.

Button Latches

Push to Open

Reflector Tabs

Fig. 1

Fig. 2a

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible

contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please

contact your nearest representative.

3. Power Supply Tray Removal -

Unscrew the two THUMB SCREWS and swing the POWER SUPPLY TRAY down as shown in Figure 3a. Disconnect the POWER

CONNECTOR and the OPTIC CONNECTOR from HOUSING. See Figure 3b. The POWER SUPPLY TRAY can now be lifted off the

bracket.

Customer First Center • 1121 Hwy 74 South • Peachtree City, GA 30269 IMI-597 AVU040197

Flite

Sheet 2 of 8

8/31/04 IMI-597

INSTALLATION INSTRUCTIONS

IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE.

RETAIN FOR FUTURE REFERENCE.

WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing

or servicing.

Power Supply

Tray

Thumb Screws

Reflector

Connector

Reflector Tabs Reflector

Fig. 2b Fig. 2c

Power Connector

Optic Connector

Fig. 3a Fig. 3b

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible

contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please

contact your nearest representative.

4. Attach Housing to Upper Flite Arm -

Remove the WIREWAY PLUG from the

HOUSING. Move the fixture leads aside so

the THREADED RODS may be accessed

through the fixture HOUSING.

See Figure 4a.

Attach the UPPER FLITE ARM to the

HOUSING by inserting the threaded studs

into the fixture HOUSING. Feed the fixture

wires through the UPPER FLITE ARM.

Slide the HOUSING over the threaded

rods and secure it with the PLAIN

WASHERS, LOCK WASHERS, and HEX

NUTS. See Figure 4b.

Torque HEX NUTS as follows:

Medium Icon (ICM) - 450 in-lbs.,

Small Icon (ICS) - 130 in-lbs.

NOTE: It may be helpful to use a deep sock-

et when installing the HEX NUTS.

Re-install the WIREWAY PLUG into the

wireway in the HOUSING.

Customer First Center • 1121 Hwy 74 South • Peachtree City, GA 30269 IMI-597 AVU040197

Flite

Sheet 3 of 8

8/31/04 IMI-597

INSTALLATION INSTRUCTIONS

IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE.

RETAIN FOR FUTURE REFERENCE.

WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing

or servicing.

WARNING

Risk of Personal Injury

Fixture may become damaged and/or

unstable if not installed properly

Tighten all fixture components to their

recommended torque values

Wireway Plug

Fig. 4a

Housing

Upper Flite

Arm

Fig. 4b

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible

contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please

contact your nearest representative.

5a. Attach the Lower Flite Arm (Single Head) -

Attach the LOWER FLITE ARM to the UPPER FLITE ARM using the three (3) 5/16-18 x 1.25” screws provided. Please see

Figure 5a. Be careful to route the wires through and along the arm so that they will not be pinched when the arms are tightened.

Torque: 250 in-lbs.

NOTE: To assure a safe product over time, check and adjust torque to proper settings each time unit is maintenanced.

5b. Attach the Lower Flite Arm (Dual Head) -

Attach the LOWER FLITE ARM to the UPPER FLITE ARM using the three (3) 5/16-18 x 1.25” screws provided. Please see

Figure 5b. Be careful to route the wires through and along the arm so that they will not be pinched when the arms are tightened.

Torque: 250 in-lbs.

NOTE: To assure a safe product over time, check and adjust torque to proper settings each time unit is maintenanced.

Customer First Center • 1121 Hwy 74 South • Peachtree City, GA 30269 IMI-597 AVU040197

Flite

Sheet 4 of 8

8/31/04 IMI-597

INSTALLATION INSTRUCTIONS

IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE.

RETAIN FOR FUTURE REFERENCE.

WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing

or servicing.

Lower Flite Arm

Fig. 5a

Fig. 5b

WARNING

Risk of Personal Injury

Fixture may become damaged and/or

unstable if not installed properly

Tighten all fixture components to their

recommended torque values

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible

contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please

contact your nearest representative.

6a. Attach the Pole Clamp (Single Head) -

Attach the POLE CLAMP to the LOWER FLITE ARM using the six (6) 3/8-16 x 0.75” screws provided as depicted in Figure 6a.

Do not tighten the screws completely; leave approximately 1/8” to 1/4” gap between the two parts. This will allow these

parts to slip over the pole with no interference.

6b. Attach the Pole Clamp (Dual Head) -

Attach the two (2) LOWER FLITE ARM using the six (6) 3/8-16 x 0.75” screws provided as depicted in Figure 6b. Do not tighten

the screws completely; leave approximately 1/8” to 1/4” gap between the two parts. This will allow these parts to slip over the

pole with no interference.

NOTE: Pole Clamps (2) and One set of six (6) 3/8 - 16 x 0.75” screws are not necessary for this assembly. Discard if desired.

Customer First Center • 1121 Hwy 74 South • Peachtree City, GA 30269 IMI-597 AVU040197

Flite

Sheet 5 of 8

8/31/04 IMI-597

INSTALLATION INSTRUCTIONS

IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE.

RETAIN FOR FUTURE REFERENCE.

WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing

or servicing.

Pole Clamp

Fig. 6a

Fig. 6b

WARNING

Risk of Personal Injury

Fixture may become damaged and/or

unstable if not installed properly

Tighten all fixture components to their

recommended torque values

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible

contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please

contact your nearest representative.

7a. Slipping the Assembly over the Pole (Single Head) -

Slip the fixture assembly over a 4-inch diameter pole as shown in

Figure 7a. There is a shoulder inside the arm that will rest on the top of

the pole. Make wiring connections at the opening at the top of the arm.

7b. Slipping the Assembly over the Pole (Dual Head) -

Slip the fixture assembly over a 4-inch diameter pole as

shown in Figure 7b. There is a shoulderinside the arm that will

rest on the top of the pole. Make wiring connections at the

opening at the top of the arm.

Customer First Center • 1121 Hwy 74 South • Peachtree City, GA 30269 IMI-597 AVU040197

Flite

Sheet 6 of 8

8/31/04 IMI-597

INSTALLATION INSTRUCTIONS

IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE.

RETAIN FOR FUTURE REFERENCE.

WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing

or servicing.

Fig. 7a

Fig. 7b

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible

contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please

contact your nearest representative.

8a. Attaching the Mast and Pole Cap (Single Head) -

Assemble the ARM MAST and POLE CAP to the fixture and arm

assembly. See Figure 8a. Tighten the six (6) screws that clamp the arm

to the pole in addition to the set screws that secure the ARM MAST and

POLE CAP.

Torque: 250 in-lbs.

NOTE: To assure a safe product over time, check and adjust

torque to proper settings each time unit is maintenanced.

8b. Attaching the Mast and Pole Cap (Dual Head) -

Assemble the ARM MAST and POLE CAP to the fixture and arm assembly.

See Figure 8b. Tighten the six (6) screws that clamp the arm to the pole in

addition to the set screws that secure the ARM MAST and POLE CAP.

Torque: 250 in-lbs.

NOTE: To assure a safe product over time, check and adjust

torque proper settings each time unit is maintenanced.

Customer First Center • 1121 Hwy 74 South • Peachtree City, GA 30269 IMI-597 AVU040197

Flite

Sheet 7 of 8

8/31/04 IMI-597

INSTALLATION INSTRUCTIONS

IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE.

RETAIN FOR FUTURE REFERENCE.

WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing

or servicing.

Fig. 8a

Fig. 8b

WARNING

Risk of Personal Injury

Fixture may become damaged and/or

unstable if not installed properly

Tighten all fixture components to their

recommended torque values

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible

contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please

contact your nearest representative.

9. Buttoning Up -

Re-install the POWER SUPPLY TRAY to the HOUSING. Connect the POWER CONNECTOR and OPTIC CONNECTOR. Swing

the POWER SUPPLY TRAY up and tighten the two THUMB SCREWS. Re-install the REFLECTOR to the HOUSING. Connect the

REFLECTOR CONNECTOR to the HOUSING. Swing the REFLECTOR up until it is secured by the REFLECTOR TABS. You

will hear an audible “click” when the REFLECTOR TABS have properly engaged. Close the fixture DOOR. See Figure 9. You will

hear two audible “clicks” when the two BUTTON LATCHES are properly engaged.

Re-lamping the Fixture

Disconnect the power to the fixture. Open the DOOR by pressing both BUTTON LATCHES at the same time. Remove the lamp

by grasping it close to the base and install the new lamp. Close the fixture DOOR. You will hear two audible “clicks” when the two

BUTTON LATCHES are properly engaged.

Customer First Center • 1121 Hwy 74 South • Peachtree City, GA 30269 IMI-597 AVU040197

Flite

Sheet 8 of 8

8/31/04 IMI-597

INSTALLATION INSTRUCTIONS

IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE.

RETAIN FOR FUTURE REFERENCE.

WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing

or servicing.

Reflector

Power Supply Tray

Outer Door

Fig. 9

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cooper Lighting Inneneinrichtung Handbücher

Cooper Lighting

Cooper Lighting Metalux 7512 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Triad 17-IW Bedienungsanleitung

Cooper Lighting

Cooper Lighting Fenestra 142 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Lumiere 6000N Leitfaden

Cooper Lighting

Cooper Lighting MCGRAW-EDISON IMI-687 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Neo-Ray 758 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Metalux 456 Bedienungsanleitung

Cooper Lighting

Cooper Lighting nooray 23ADIW Bedienungsanleitung

Cooper Lighting

Cooper Lighting FAIL-SAFE SCF12 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Fail-Safe FWS Bedienungsanleitung

Cooper Lighting

Cooper Lighting Neo-Ray Symbio 194 Bedienungsanleitung

Cooper Lighting

Cooper Lighting 213 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shaper 695-WP-DB Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting Fenestra 174 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Sure-Lites AA1 Bedienungsanleitung

Cooper Lighting

Cooper Lighting METALUX 2HB55 Bedienungsanleitung

Cooper Lighting

Cooper Lighting PM132ob Bedienungsanleitung

Cooper Lighting

Cooper Lighting Fail-Safe X10 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Impact Wall Medium IMI-699 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Portfolio H6004T Bedienungsanleitung

Cooper Lighting

Cooper Lighting FAIL-SAFE MPWC Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shaper 609 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Luminous Wall Sconce 606 Bedienungsanleitung

Cooper Lighting

Cooper Lighting 417 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung