Cooper Lighting Portfolio MD6CPxT4 Bedienungsanleitung

704530 Rev. A - 1 - Customer First Center · 1121 Highway 74 South · Peachtree City, GA 30269

Portfolio®

Installation Instructions for MD6xT6, MD6xT4, MD6CPxT6 and MD6CPxT4

Commercial Recessed Housings

CAUTION: To avoid possible electrical shock, be sure that power supply is turned off before installing or servicing this

fixture.

CAUTION: Metal halide lamps have arc tubes that operate at extremely high temperatures and may shatter unexpectedly

as a result of misapplication, system failure or internal factors. This violent failure could cause extremely hot glass

and lamp parts to discharge into the surrounding environment, creating a risk of personal injury, fire or property

damage. Therefore, it is incumbent on the user to use common sense and good judgment in anticipation of these

potential violent failures. Never use or operate this fixture without safety glass or lens properly installed and secured in

place.

Reduction of Risk

The potential of violent failure can be significantly reduced by relamping at or before the rated end of life. In applications

where the lamps burn continuously, the lamps should be turned off for a period of 15 minutes at least once per week

which will cause lamps nearing their end of life to fail passively upon relighting. Careful adherence to the above

precautions may not eliminate all possible risks associated with the use of Metal Halide lamps, but it will reduce the

likelihood of personal injury or property damage.

Rough-In Mounting

•This fixture should be supported by main runners or

other structure that is capable of supporting fixture

weight of 17lbs.

•The junction box will accept both ½” and ¾” trade size

metal conduit.

•Review fixture labeling to make sure it is rated for the

voltage installation being used.

•The housing is designed for installation where it will

not come in contact with insulation. Thermal insulation

must be kept a minimum of three inches (3”) away

from the housing sides, top and junction box.

•This housing/trim is designed to be used with T6/T4.5

Ceramic Metal Halide lamps for the specified wattages

only. These lamps can cause serious skin burn and

eye inflammation from shortwave ultraviolet radiation if the envelope of the lamp is broken or punctured.

Risk Of Fire

Supply conductors (power

wires) connecting the fixture

must be rated minimum

90°C. If uncertain, consult an

electrician.

Risk Of Electrical Shock

Disconnect power at fuse or

circuit breaker before

installing or servicing.

Risk Of Fire.

Do not install insulation

within 3 inches (76 mm) of

any part of the fixture or in a

way that may entrap heat.

704530 Rev. A - 2 - Customer First Center · 1121 Highway 74 South · Peachtree City, GA 30269

Portfolio®

Step 1. Install fixture into ceiling cavity using ½” electrical conduit, ¾” channel, 1½” channel or  “ x ½” bar stock as

mounting rails (furnished by others) by inserting them into hanger brackets at both ends of the fixture as shown.

Step 2. Secure mounting rails to support structures.

Step 3. Adjust fixture so bottom of plaster ring is flush with finished ceiling line, using screws securing hanger brackets.

Hanger bracket is reversible for a total adjustment of 5”.

Electrical Connection

CAUTION: Make certain no bare wires are exposed outside of wire nut connectors.

Step 4. Provide electrical service according to the “National Electrical Code” or your local electrical code to the junction

box (located on the plaster frame). Supply wire insulation must be rated for at least 90° C. The junction box is

also rated for a maximum of 12 No. 12 AWG Branch Circuit conductors suitable for at least 90°C.

Step 5. Remove junction box cover.

Step 6. Remove appropriate round pryout and connect conduit to junction box with proper connector (not included).

Step 7. Connect supply lead wires to junction box lead wires (line, neutral and ground) in fixture using properly sized

wire nuts (not included). Be careful not to leave any bare conductors outside of the wire nut connectors.

Step 8. 120V or 277V AC Supply: Connect white to white, black to black and green (from electrical service) to the bare

copper wire in the junction box. See the appropriate wiring diagram for more detail.

Place all connections and excess wiring into the junction box and replace cover.

704530 Rev. A - 3 - Customer First Center · 1121 Highway 74 South · Peachtree City, GA 30269

Portfolio®

Distribution Selection & Trim Installation

Step 1. Install the proper lamp type and wattage into the socket. Make sure the new lamp does not have any

fingerprints, dust, lint, etc.

NOTE: The lamp-socket assembly is installed onto the trim in one of three possible positions. These are labeled

Narrow, Medium and Wide. The selected position determines the light distribution from the fixture.

Step 2. As shown in figure at right, the trim assembly includes

six plastic lockout inserts. Remove and discard the

two lockouts from the desired distribution positions.

For example, if a Medium distribution is desired,

remove the two lockouts closest to the “Medium”

labels.

NOTE: It is intended that the remaining plastic lockouts remain

in place. This will help avoid any inadvertent

distribution changes during re-lamping in the future.

Step 3. Secure the lamp-socket assembly in the desired

distribution position with the two thumbscrews.

Step 4. Install the trim into the housing. The trim’s torsion

springs pass through slots in torsion spring receivers

inside the housing.

704530 Rev. A - 4 - Customer First Center · 1121 Highway 74 South · Peachtree City, GA 30269

Portfolio®

Lamping Information

•The electronic ballast has a very important shutdown timing feature that turns off the ballast output after time

periods ranging from 2 minutes up to 30 minutes if a lamp does not start or operate properly or if the fixture wiring

is improper. For proper system diagnosis and at lamp replacement time, the INPUT POWER TO THE BALLAST

MUST BE RESET (turn power off, wait 10 seconds, turn power back on) to start a new lamp.

•Take proper care in handling and disposing of the old lamp. Do not touch glass bulb with bare hands.

•Lamp contains Mercury. Manage in accordance with disposal laws. See www.lamprecycle.org or 1-866-666-

6850.

Main Lamp

Ceramic Metal Halide Lamp

MD6xT6G12 Housings

G12 socket for one 20W, 39W, 70W or 150W lamp. Generic lamp

designations (lamp by others):

M156/E (20W)

M130/E (39W)

M98/E, M139/E (70W)

M102/E, M142/E (150W)

MD6xT4G85 Housings

G8.5 socket for one 20W, 39W, or 70W lamp. Generic lamp

designations (lamp by others):

M156/E (20W)

M130/E (39W)

M98/E, M139/E (70W)

MD6xT4G65 Housings

GU6.5 socket for one 20W or 39W lamp. Generic lamp designations

(lamp by others):

M156/E (20W)

M130/E (39W)

Quartz Lamp

Quartz Restrike Lamp

The Quartz lamp is a 100W, 120V, T4 Bulb with a “DC Bayonet” base.

This housing may be re-lamped either from below or above the ceiling.

Allow sufficient time for the lamp to cool.

704530 Rev. A - 5 - Customer First Center · 1121 Highway 74 South · Peachtree City, GA 30269

Portfolio®

To re-lamp from below the ceiling:

Step 1. Remove the lower trim by gently pulling the trim

down until the torsion spring stops are reached.

Remove the trim from the torsion spring receivers.

Step 2. Remove the socket assembly from the top of the

trim using the two thumbscrews. Use gloves if the

assembly is still warm. Gently remove the old

lamp. Dispose the old lamp according to local

recycling code.

Step 3. Install the new lamp. Make sure the new lamp

does not have any fingerprints, dust or lint.

Step 4. Re-assemble the socket assembly back onto the

trim. Be sure to re-assemble the lamp

assembly in the same distribution as before

(Narrow, Medium or Wide). Secure with the two

thumbscrews.

Step 5. Install the trim back into the housing using the

torsion springs.

To re-lamp from above the ceiling:

Step 1. Remove the top cover.

Step 2. Remove the socket assembly from the top of the

trim using the two thumbscrews. Use gloves if the

assembly is still warm. Gently remove the old

lamp. Dispose the old lamp according to local

recycling code.

Step 3. Install the new lamp. Make sure the new lamp

does not have any fingerprints, dust or lint.

Step 4. Re-assemble the socket assembly back onto the

trim. Be sure to re-assemble the lamp

assembly in the same distribution as before

(Narrow, Medium or Wide). Secure with the two

thumbscrews.

Step 5. Install the trim back into the housing using the torsion springs.

704530 Rev. A - 6 - Customer First Center · 1121 Highway 74 South · Peachtree City, GA 30269

Portfolio®

Ballast Replacement

•The ballast should be replaced by a qualified electrician.

•The ballast may be replaced either from below or above the ceiling.

Step 1. Remove the trim assembly.

Step 2. Inside the housing, remove the access door to provide access to the ballast and junction box.

Step 3. Remove the existing ballast and replace with the new ballast. Refer to the applicable wiring diagram at the end

of this document.

Step 4. Close the access door. Re-install the trim.

Lens Maintenance & Replacement

Do not operate without the lens in place. These lamps require the containment

provided by the lens. These lamp types can only be used in enclosed luminaires, for

which the lens is required.

Step 1. Remove the trim assembly from the housing.

Step 2. Slide the Upper Reflector assembly off of the Lower Reflector assembly.

Step 3. To Clean Lens: Gently wipe with a soft, clean, dry, lint free cloth to remove

dust. Use mild detergent solution on a soft cloth to remove fingerprints

and stains. Rinse with clean water and dry with lint free cloth.

Step 4. Install the new/clean lens, and slide the Upper Reflector assembly back in

place.

Insulation Detector Replacement

The insulation detector may be replaced from above or below the ceiling.

Step 1. Open the Junction Box.

Step 2. Remove the existing Insulation Detector, and replace with the new one.

Step 3. Wire the new Insulation Detector as before. For reference, see the wiring diagrams contained in this document.

Socket Replacement

Step 1. If replacing from below the ceiling, remove the trim assembly from the housing.

Step 2. Remove the socket assembly from the top of the trim using the two thumbscrews. Use gloves if the assembly is

still warm. Gently remove the lamp.

704530 Rev. A - 7 - Customer First Center · 1121 Highway 74 South · Peachtree City, GA 30269

Portfolio®

Step 3. Remove the socket from the bracket by removing the two Philips screws which secure it in place.

Step 4. Install the new socket using the original screws.

Step 5. Install the lamp. Make sure the lamp does not have any fingerprints, dust or lint.

Step 6. Re-assemble the socket assembly back onto the trim. Be sure to re-assemble the lamp assembly in the

same distribution as before (Narrow, Medium or Wide). Secure with the two thumbscrews.

Step 7. Install the trim back into the housing using the torsion springs.

Wiring Diagrams

1. For Housings with Ballasts requiring dedicated voltage input. Includes Catalog Numbers MD6xxx1E and MD6xxx2E.

704530 Rev. A - 8 - Customer First Center · 1121 Highway 74 South · Peachtree City, GA 30269

Portfolio®

2. For Housings with Ballasts requiring dedicated voltage input, and a Quartz Restrike System. Includes Catalog

Numbers MD6xxx1EQ and MD6xxx2EQ.

3. For Housings with Ballasts requiring dedicated voltage input, and an Emergency Circuit Quartz Lamp. Includes

Catalog Numbers MD6xxx1EX and MD6xxx2EX.

704530 Rev. A - 9 - Customer First Center · 1121 Highway 74 South · Peachtree City, GA 30269

Portfolio®

4. For Housings with Universal voltage input, 120-277V, with Advance Ballast (70W). Includes Catalog Numbers

MD6xxxG12E, MD6xxxG85E and MD6xxxG65E.

5. For Housings with Universal voltage input, 120-277V, with Advance Ballast (70W) and a Quartz Restrike System.

Includes Catalog Numbers MD6xxxG12EQ, MD6xxxG85EQ and MD6xxxG65EQ.

704530 Rev. A - 10 - Customer First Center · 1121 Highway 74 South · Peachtree City, GA 30269

Portfolio®

6. For Housings with Universal voltage input, 120-277V, with Advance Ballast (70W) and an Emergency Circuit Quartz

Lamp. Includes Catalog Numbers MD6xxxG12EX, MD6xxxG85EX and MD6xxxG65EX.

7. For Housings with Universal voltage input, 120-277V, with Vossloh Schwabe Ballast (20W or 39W). Includes Catalog

Numbers MD6xxxG12E, MD6xxxG85E and MD6xxxG65E.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cooper Lighting Inneneinrichtung Handbücher

Cooper Lighting

Cooper Lighting FAIL-SAFE TF28 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Lazer LZR401 Bedienungsanleitung

Cooper Lighting

Cooper Lighting QCT1876 Bedienungsanleitung

Cooper Lighting

Cooper Lighting 1463 Bedienungsanleitung

Cooper Lighting

Cooper Lighting HALO L1730 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Lumiere Zuma 1201 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Thin Profile Exit TPX Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting PORTFOLIO MD6150T6G12 Bedienungsanleitung

Cooper Lighting

Cooper Lighting MCGRAW-EDISON 70 - 200W Bedienungsanleitung

Cooper Lighting

Cooper Lighting Metalux M Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting PM132ob Bedienungsanleitung

Cooper Lighting

Cooper Lighting 226 Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting FAIL-SAFE FDI Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shaper 687-WP Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shaper 689 Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting Lumiere 1070 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Sure-Lites RG1 Bedienungsanleitung

Cooper Lighting

Cooper Lighting HALO L1816 Bedienungsanleitung

Cooper Lighting

Cooper Lighting FWE Bedienungsanleitung

Cooper Lighting

Cooper Lighting Impact Wall Medium IMI-699 Bedienungsanleitung

Cooper Lighting

Cooper Lighting IRIS E7AA20 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shaper 693-S/4 Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting FAIL-SAFE FMS24LP Bedienungsanleitung

Cooper Lighting

Cooper Lighting L4005 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung