Cooper Lighting TMU/TLU Bedienungsanleitung

Tools Required Socket, 5/16" Socket, 3/4" Deep Well Socket, Electrical

wiring tools.

NOTE: These luminaires are designed for outdoor lighting

services, and should not be used in area of limited ventilation

or in high ambient temperature enclosures. Construction is

suitable for down lighting only. Best results will be obtained

if installed and maintained according to the following

recommendations.

1. Remove housing assembly and arm components from carton. Remove

power tray if fixture is not hard mount version.

2. With the fixture on its back, open and remove door by pressing thumb

latches outward at the same time, open the door and lift it from the

hinges. FIG. 1

3. Run the threaded rods (2) through the center of the semi-enclosed hole

details in the arm extrusion. To help orient the arm correctly with the

housing, please note that one end of the extruded arm has an angled cut

and the other has a perpendicular cut with two drain notches located on

the bottom. If assembling to a round pole, use the round pole adapter

with the drain channels located at the extruded arm end with the drain

slots. Mate the angled side of the extruded arm to the housing so that

the bottom surface of the extrusion is parallel to the bottom of the

fixture, and the drain notches are facing down and located away from

the housing. FIG. 2 Slide the threaded rods into the interior of the

housing. Attach flat washer, lock washer, and nut into place in the order

shown in FIG. 2. Torque hex nuts to 450 lb/in.

4. If necessary, remove the cap on the pole. Position the housing and arm

to assemble it to the pole. Lower the nut plate into the interior of the

pole as shown. Slide the threaded rods through the pole and thread into

the nut plate until the rod protrudes though the nut plate slightly. Tighten

both nuts located inside of the housing to 30 lb/ft of torque.

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency

during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest

representative.

Talon Medium

Sheet 1 of 3

7/23/08 IMI-687SW

INSTALLATION INSTRUCTIONS

IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE.

WARNING: Risk of Fire/Electric Shock. If not qualified, consult an electrician.

WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing.

WARNING: Risk of Burn. Disconnect power and allow fixture to cool before changing bulb or handling fixture.

WARNING: Risk of Personal Injury. Fixture may become damaged and/or unstable if not installed properly. Tighten all fixture components

to their recommended torque values.

WARNING: Risk of Fire/Electrical Shock. Upside down installation can result in overheating or accumulation of water in fixture.

Install right side up.

NOTE: Specifications and dimensions subject to change without notice.

Visit our web site at www.cooperlighting.com

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 ADW081604

FIG. 1

Latches

FIG. 2

Hardware: Washer,

Lock Washer, and

Hex Nut

Arm

Nut Plate

Fits Inside

of Pole

Round Pole

Adapter

(Optional)

Mounting Rod (2)

5. With the pole and fixture(s) raised into position, place the power tray

onto the hinges of the housing electrical compartment and let

it hang free. Locate the power connector plug and rotate the power tray

until the connection can be made with the mating connector in the

housing. Raise the powertray until the two wing screws engage and

tighten until fully snug.

6. Replace door on the hinges at the rear of the housing, rotate into

position, and assure that both latches are fastened securely.

FIXTURE MAINTENANCE

RELAMPING

1. Disengage both latches and open the door. Do not let the door swing

freely on the hinges.

2. Replace the lamp with the appropriate type and wattage and reassemble

the refractor to the upper housing. FIG. 3

3. Close the door and assure that the latches are securely fastened.

PLUG-IN STARTER REPLACEMENT

This procedure applies to fixtures with a plug-in type starter. Disengage

both latches and open the door. Do not let the door swing freely on the

hinges. Loosen the power tray thumb screws, unplug the power connector

as you lower the powertray, and continue lowering until the powertray

hangs free on the hinges. The starter is located in the position shown.

Remove and replace. Reverse the directions to secure the powertray and

the door after starter replacement.

1. Remove the plug-in starter from the receptacle and replace.

FIG. 4 and FIG. 5

2. Assure that the wing screws on the powertray and both latches on the

door are fastened securely.

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency

during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest

representative.

Talon Medium

Sheet 2 of 3

7/23/08 IMI-687SW

INSTALLATION INSTRUCTIONS

IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE.

WARNING: Risk of Fire/Electric Shock. If not qualified, consult an electrician.

WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing.

WARNING: Risk of Burn. Disconnect power and allow fixture to cool before changing bulb or handling fixture.

WARNING: Risk of Personal Injury. Fixture may become damaged and/or unstable if not installed properly. Tighten all fixture components

to their recommended torque values.

WARNING: Risk of Fire/Electrical Shock. Upside down installation can result in overheating or accumulation of water in fixture.

Install right side up.

NOTE: Specifications and dimensions subject to change without notice.

Visit our web site at www.cooperlighting.com

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 ADW081604

FIG. 3

Thumbscrews (2)

Powertray

FIG. 4

FIG. 5

Plug-In Starter

NEMA PHOTOCONTROL REPLACEMENT

1. The photocontrol is mounted on top the housing. FIG. 6

2. Remove the photocontrol by twisting counterclockwise and

replace.

OPTIC DISTRIBUTION AND ORIENTATION

The Talon Medium fixture is offered with some optics that

have directional distributions. For aiming purposes, the Talon

Medium was designed with the flexibility to allow each of its optics

to be rotated to any of four positions, located at 90° increments.

To change the optic orientation, open the door and remove the

lamp. Use a screwdriver to remove the four screws as shown in

FIG. 7. Reposition the optic, insert the screws and tighten securely.

These instructions do not claim to cover all details or variations in

the equipment, procedure, or process described, nor to

provide directions for meeting every possible contingency

during installation, operation or maintenance. When additional

information is desired to satisfy a problem not covered

sufficiently for user's purpose, please contact your nearest

representative.

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency

during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest

representative.

Talon Medium

Sheet 3 of 3

7/23/08 IMI-687SW

INSTALLATION INSTRUCTIONS

IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE.

WARNING: Risk of Fire/Electric Shock. If not qualified, consult an electrician.

WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing.

WARNING: Risk of Burn. Disconnect power and allow fixture to cool before changing bulb or handling fixture.

WARNING: Risk of Personal Injury. Fixture may become damaged and/or unstable if not installed properly. Tighten all fixture components

to their recommended torque values.

WARNING: Risk of Fire/Electrical Shock. Upside down installation can result in overheating or accumulation of water in fixture.

Install right side up.

NOTE: Specifications and dimensions subject to change without notice.

Visit our web site at www.cooperlighting.com

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 ADW081604

FIG. 7

Remove Optic, Rotate

To Desired Position

and Fasten Into Place

FIG. 6

NEMATwistlock

Photocontrol

Inhaltsverzeichnis

Andere Cooper Lighting Inneneinrichtung Handbücher

Cooper Lighting

Cooper Lighting IMI-682 Bedienungsanleitung

Cooper Lighting

Cooper Lighting AMETRIX ADY071468 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shaper 661 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Sure-Lites CAX Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shaper 1215-TTR Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting Neo-Ray Geo 14-DIP Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shaper 689 Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shaper 1215-2TR SERIES Bedienungsanleitung

Cooper Lighting

Cooper Lighting HALO L2001 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shaper 676-WP SERIES Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shaper 494-RP SERIES Bedienungsanleitung

Cooper Lighting

Cooper Lighting 1270 Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting Lumark XB Bedienungsanleitung

Cooper Lighting

Cooper Lighting Portfolio 828 Bedienungsanleitung

Cooper Lighting

Cooper Lighting LV2060ISMulti-Lamp Luminaire LV2060IS Bedienungsanleitung

Cooper Lighting

Cooper Lighting HALO L1735 Bedienungsanleitung

Cooper Lighting

Cooper Lighting FAIL-SAFE EYELITE 12" Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shaper 1250-3R Bedienungsanleitung

Cooper Lighting

Cooper Lighting TLU Talon Large TL91SWW3VFG Bedienungsanleitung

Cooper Lighting

Cooper Lighting New-Ray 44-DS Bedienungsanleitung

Cooper Lighting

Cooper Lighting LF Bedienungsanleitung

Cooper Lighting

Cooper Lighting FAIL-SAFE SCF12 Bedienungsanleitung

Cooper Lighting

Cooper Lighting AMETRIX 1249 Bedienungsanleitung

Cooper Lighting

Cooper Lighting METALUX 15/ASY Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung