Covidien ForceTriad Referenzhandbuch

1044008_book.book Page 1 Thursday, August 18, 2011 2:43 PM

page 2

Monopolar Setup Instructions

Monopolar Surgery Setup

Avertissement: Risque du feu.

Remplacez les fusibles comme marqués.

250 V F8.0A (100-240)

Warning: Risk of Fire.

Replace Fuse as Marked.

250V, F8.0A (100-240)

ForceTriad Energy Platform

front panel

ForceTriad Energy Platform

rear panel

page 3

Monopolar Setup Instructions

Monopolar Surgery Setup

Note: Please read the ForceTriad Energy Platform User’s Guide and all appropriate instructions for use before

using the ForceTriad Energy Platform or surgical accessories.

1. Plug the system power cord into the rear panel receptacle of the ForceTriad Energy Platform and into a grounded

power receptacle. (Do not use a power strip or extension cord.)

2. Turn on the ForceTriad Energy Platform and verify that the self-test is successfully completed. When the system is

operational, the touchscreen appears.

Note: Do not touch the screens during power up.

3. If using a footswitch, connect it to the monopolar footswitch receptacle on the rear panel. This may require an

adapter to connect a standard four-pin monopolar footswitch.

4. Apply the REM Polyhesive™Patient Return

Electrode to the patient and connect it to

the patient return electrode receptacle on

the front panel.

Confirm that the red REM indicator turns

from red to green.

5. Connect a monopolar instrument as

directed on the following pages. Patient return electrode connection

1044008_book.book Page 3 Thursday, August 18, 2011 2:43 PM

page 4

Monopolar Setup Instructions

Standard Two-Button Electrosurgical Instruments

1. Connect the two-button instrument into either the Monopolar 1 or

Monopolar 2 instrument receptacle on the front panel of the energy platform.

Note: When attaching a monopolar instrument, align the instrument’s

connector pins with the three dots printed on the ForceTriad face plate below

the monopolar receptacles. Reversing the connector will limit the instrument’s

functionality and damage the connector.

Note: Each touchscreen controls the receptacle directly below the touchscreen

and can only control one instrument at a time. Do not plug in more than one

instrument under one touchscreen.

2. Confirm that the Standard Monopolar (Std Mono) tab appears in the

appropriate touchscreen.

3. Select the power output level by touching the green up and down arrows for either the Cut or Coag mode.

4. Select the surgical mode:

a. For the Cut mode, touch either the yellow Pure or yellow Blend button.

b. For the Coag mode, touch either the blue Fulgurate or blue Spray button.

Note: If no surgical mode is selected, the Cut mode defaults to Pure and the Coag mode defaults to Fulgurate.

Std Mono Valleylab Acc. Port

Cut

REM

Pure

Blend

Coag

Spray

Fulg

Monopolar touchscreen –

standard configuration

1044008_book.book Page 4 Thursday, August 18, 2011 2:43 PM

page 5

Monopolar Setup Instructions

Valleylab Mode-Enabled Electrosurgical Devices

1. Connect the Valleylab™mode-enabled device into either the Monopolar 1

or Monopolar 2 instrument receptacle on the front panel of the energy

platform.

Note: Each touchscreen controls the receptacle directly below the

touchscreen and can only control one instrument at a time. Do not plug in

more than one instrument under one touchscreen.

2. Confirm that the Valleylab tab appears in the appropriate touchscreen.

Note: When a Valleylab mode-enabled device is connected, the system

selects the default power zone setting for the recognized instrument.

3. Adjust the power zone setting by touching the desired gold bar.

4. While in the sterile field, move the slider control on the device to adjust power output within the selected power

zone.

Note: The Cut function can be disabled by pressing the Cut power display.

Monopolar touchscreen –

Valleylab configuration

Std Mono Valleylab Acc. Port

REM

Coag

Cut

Manual

1044008_book.book Page 5 Thursday, August 18, 2011 2:43 PM

page 6

Monopolar Setup Instructions

Manual Power Control Mode

Touch the green Manual button to select specific power settings not available in the sterile field control setting.

Note: The slider cannot control power when the energy platform is in the Manual Power Control mode.

Monopolar Footswitching

The ForceTriad Energy Platform provides hardware and software options for monopolar footswitching. Standard

monopolar footswitching is a simple hardware configuration. Software-enabled footswitching provides footswitching

capabilities for both footswitching and handswitching accessories from the Monopolar 1 receptacle.

1044008_book.book Page 6 Thursday, August 18, 2011 2:43 PM

page 7

Monopolar Setup Instructions

Standard Monopolar Footswitching

1. Connect the instrument to the universal footswitch accessory port (UFP)

on the front panel of the ForceTriad Energy Platform.

Note: An E0502-1 or E0017 adapter is required when using the universal

footswitching accessory port with accessories that have pin diameters less

than 8 mm.

2. Confirm that the Accessory (Acc.) Port tab appears in the first touchscreen.

Note: Each touchscreen controls the receptacle directly below the

touchscreen and can only control one instrument at a time. Do not plug in

more than one instrument under one touchscreen.

3. Select the power output level by touching the green up and down arrows

for either the Cut or Coag mode.

4. Select the surgical mode:

a. For the Cut mode, touch either the yellow Pure or yellow Blend button.

b. For the Coag mode, touch either the blue Fulgurate or blue Spray button.

Note: If no surgical mode is selected, the Cut mode defaults to Pure and the Coag mode defaults to Fulgurate.

Std Mono Valleylab Acc. Port

Cut

Coag

REM

Pure

Blend Spray

Fulg

Monopolar touchscreen –

Acc. Port configuration

1044008_book.book Page 7 Thursday, August 18, 2011 2:43 PM

page 8

Monopolar Setup Instructions

Software Enabled Monopolar 1 Footswitching

1. Enable Monopolar 1 footswitching at the system level: Touch the wrench icon—Setup—Features—

Mono 1. The mark in the check box indicates it is enabled.

2. Exit the menus by touching the green arrows at the bottom of each screen.

3. A footswitching button with a red X is added the Standard Monopolar and

Valleylab tabs in the left touchscreen. Select the desired tab.

4. Enable Monopolar 1 footswitching at the local level by touching the button.

The X is removed. Operation of handswitching or footswitching instruments

is now enabled from the Monopolar 1 footswitching port.

5. Attach a two-pedal footswitch or three-pedal Valleylab mode-enabled

footswitch to the monopolar footswitch receptacle on the back panel.

6. Attach any monopolar instrument to the Monopolar 1 instrument receptacle

on the front panel.

7. Select the settings for the procedure.

8. Step on the appropriate footswitch to deliver monopolar power to the attached instrument.

Std Mono

Valleylab Acc. Port

Cut

Coag

REM

Pure

Blend Spray

Fulg

Monopolar 1 Footswitching

enabled at system level

1044008_book.book Page 8 Thursday, August 18, 2011 2:43 PM

page 9

Monopolar Setup Instructions

Note: If Monopolar 1 footswitching has not been enabled, a box appears indicating FOOTSWITCH CONTROL NOT

ENABLED. Touch the green button with a check mark to enable Monopolar 1 footswitching from this screen.

1044008_book.book Page 9 Thursday, August 18, 2011 2:43 PM

1044008_book.book Page 10 Thursday, August 18, 2011 2:43 PM

Andere Handbücher für ForceTriad

Inhaltsverzeichnis

Andere Covidien Medizinische Geräte Handbücher

Covidien

Covidien Nellcor GR101704 Bedienungsanleitung

Covidien

Covidien Nellcor OxiMax N-600x Bedienungsanleitung

Covidien

Covidien Endo Stitch Bedienungsanleitung

Covidien

Covidien Kangaroo Bedienungsanleitung

Covidien

Covidien Puritan Bennett 540 Bedienungsanleitung

Covidien

Covidien INVOS 5100C Bedienungsanleitung

Covidien

Covidien ForceTriad Bedienungsanleitung

Covidien

Covidien INVOS 5100C Bedienungsanleitung

Covidien

Covidien Newport e360 Bedienungsanleitung

Covidien

Covidien Nellcor Series Montage- und Bedienungsanleitung

Covidien

Covidien WarmTouch Bedienungsanleitung

Covidien

Covidien Nellcor Bedienungsanleitung

Covidien

Covidien Shiley 135810 Bedienungsanleitung

Covidien

Covidien Valleylab LS10 Bedienungsanleitung

Covidien

Covidien Valleylab FX8 Series Bedienungsanleitung

Covidien

Covidien Shiley 18710 Bedienungsanleitung

Covidien

Covidien Kendall SCD 700 Series Bedienungsanleitung

Covidien

Covidien Nellcor PM100N Betriebsanleitung

Covidien

Covidien Puritan Bennett 700 Series Bedienungsanleitung

Covidien

Covidien Valleylab LS10 Bedienungsanleitung

Covidien

Covidien Shiley 50XLTCP Bedienungsanleitung

Covidien

Covidien Puritan Bennett 560 Bedienungsanleitung

Covidien

Covidien Shiley 4UN65A Bedienungsanleitung

Covidien

Covidien Nellcor PM10N Bedienungsanleitung

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

Medipost-Nutristoma

Medipost-Nutristoma MD300K2 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

FujiFilm

FujiFilm Sonart Betriebsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Stryker

Stryker SPR Plus Bedienungsanleitung