Craftsman 486.244411 Bedienungsanleitung

Operator's Manual

42" SNOW BLADE

Model No. 486.244411

PRINTED IN U.S.A.

FORM NO. 41337 (03/15/10)

CAUTION:

Before using this product, read

and follow all Safety, Assembly

and Operating Instructions

• Safety

• Assembly

• Operation

• Maintenance

• Parts

Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A.

www.sears.com/craftsman

IMPORTANT: For Missing Parts or

Assembly Questions Call 866-576-8388

STOP

DO NOT RETURN TO STORE

For Missing Parts or Assembly

Questions Call 1-866-576-8388

TABLE OF CONTENTS

MODEL NUMBER: 486.244411

SERIAL NUMBER: __________________

DATE OF PURCHASE: __________________

The model number and serial numbers will be found on

a decal attached to the snow blade.

You should record both the serial number and the

date of purchase and keep in a safe place for future

reference.

MAINTENANCE............................................................ 12

SERVICE AND ADJUSTMENTS....................................13

STORAGE.................................................................13

TROUBLESHOOTING...............................................14

REPAIR PARTS ILLUSTRATION......................................18

REPAIR PARTS LIST................................................19

PARTS ORDERING/SERVICE...............BACK COVER

Look for this symbol to point out important safety precautions.It means — Attention!! Become

alert!! Your safety is involved.

SAFETY

WARRANTY.................................................................... 2

SAFETY RULES ............................................................. 2

ACCESSORIES AND ATTACHMENTS........................... 3

FULL SIZE HARDWARE CHART................................... 3

CARTON CONTENTS .................................................... 4

ASSEMBLY................................................................ 5-10

OPERATION............................................................ 11-12

Read the tractor and snow blade owner's manuals•

and know how to operate your tractor before using

tractor with snow blade attachment.

Never operate tractor and snow blade without•

wearing proper clothing suited to weather conditions

and operation of controls.

Never allow children to operate tractor and snow•

blade, and do not allow adults to operate without

proper instructions.

Alwaysbeginwithtransmissioninrst(low)gearand•

gradually increase speed as conditions permit.

Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the

equipment. Exercise caution at all times when using power equipment.

ACCESSORIES AND ATTACHMENTS

WHEEL WEIGHT TIRE CHAINS WEIGHT BRACKET

FOR DRAW BAR

SNOW CAB

Theseandotheraccessoriesarerecommendedforusewithyourunit.Call1-800-4-MY-HOME®tondoutiftheyareavailable.

If available, they may be purchased at most Craftsman outlets or by calling 1-800-4-MY-HOME®.

FULL SIZE HARDWARE CHART

REF. QTY. DESCRIPTION REF. QTY. DESCRIPTION

A 1 Hex Bolt, 1/4-20 x 3-1/4" LG.

B 1 Hex Bolt 1/4-20 x 1-1/2"

C 1 Hex Bolt, 5/16-18 x 1-1/2"

D 14 Hex Bolt, 3/8-16 x 1"

E 2 Carriage Bolt, 3/8 x 1-1/4"

F 2 Carriage Bolt, 5/16 x 1"

G 6 Hex Bolt, 3/8" x 1" (Thread Forming)

H 6 Carriage Bolt, 3/8" x 1"

I 2 Hex Jam Nut, 5/16-24 Thread

J 3 Nylock Hex Nut, 1/4-20 Thread

K 3 Nylock Hex Nut, 5/16-18 Thread

L 18 Nylock Hex Nut, 3/8-16 Thread

M 8 Large 1/2" Washer

N 6 3/8" Flat Washer

O 4 Hairpin Cotter

P 2 Cotter Pin 1/8" x 1-1/4"

Q 1 1/2" Washer

R 6 Lock Washer, 3/8"

S 2 Palnut, 3/8"

T 1 Spacer, 9/16" OD x 5/8" LG.

U 2 Spacer, 9/16" OD x 1" LG.

V 2 Shoulder Bolt, 3/8 x .9"

A B

N Q

SPECIAL

USE ONLY

WARRANTY

ONE YEAR FULL WARRANTY

When operated and maintained according to the instructions supplied with it, if this Snow Blade fails due to a defect in

material or workmanship within one year from the date of purchase, call 1-800-4-MY-HOME® to arrange for free repair (or

replacement if repair proves impossible).

If this product is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase.

Thiswarrantygivesyouspeciclegalrights,andyoumayalsohaveotherrightswhichvaryfromstatetostate.

Sears, Roebuck and Co., Hoffman Estates, IL 60179

REF. QTY. DESCRIPTION REF. QTY. DESCRIPTION

12 1 Hanger Bracket, L.H.

13 1 Hanger Bracket, R.H.

14 1 Pivot Support Bracket

15 2 Angle Support Bracket

16 1 Channel Assembly

17 1 Blade Assembly

18 1 Blade Pivot Rod

19 1 Lift Handle Tube

20 1 Lift Handle Rod

21 1 Cable

22 2 Slotted Angle Support Bracket

23 1 Quick Attach Bracket (RH)

24 1 Quick Attach Bracket (LH)

1 2

8 9

REF. QTY. DESCRIPTION REF. QTY. DESCRIPTION

1 2 Cable End Fitting

2 1 Cable Mount Bracket

3 1 Angle Lock Spring

4 2 Nylon Tie

5 1 Spring Mount Rod

6 1 Channel Pivot Pin

7 1 Blade Adjust Spring

8 1 Plastic Grip

9 1 Grip Assembly

10 2 Angle Lock Bars

11 1 Blade Pivot Shaft

PARTS IN PACKAGES NOT SHOWN FULL SIZE

CARTON CONTENTS (Loose Parts in Carton)

ASSEMBLY

(1) Pliers

(1) Hammer

(1) Adjustable Wrench (or socket set)

(1) 9/16" Open End or Box End Wrench

(1) 7/16" Open End or Box End Wrench

(1) 1/2" Open End or Box End Wrench

TOOLS REQUIRED FOR ASSEMBLY

LOCATE MOWER SUSPENSION BRACKETS

Look under the front of your tractor.•

If there is a single mower deck suspension•

bracket located underneath the middle of the front

axle as shown in the image below, proceed to

INSTRUCTIONS FOR TRACTORS WITH SINGLE

FRONT DECK SUSPENSION BRACKET below.

If your tractor does not have a mower deck•

suspension bracket underneath the middle of

the front axle, proceed to INSTRUCTIONS FOR

TRACTORS WITH DUAL FRONT SUSPENSION

BRACKETS on page 6.

MOWER DECK

SUSPENSION

BRACKET

NOTE: Not all of the supplied parts and hardware will be

needed for one particular tractor. Unneeded items may be

discarded after assembly has been completed.

NOTE: Right hand (RH) and left hand (LH) are

determined from the operator's position while seated on

the tractor.

CAUTION: Do not begin assembling until

thetractorengine,muferandexhaust

deectorhavebeenallowedtocooloff.

REMOVE

BROWNING

SHIELD

FIGURE 1

STEP 1: (SEE FIGURE 1)

Remove the tractor hood. Refer to your tractor owners•

manual for instructions on how to properly remove

the hood.

Remove the browning shield from the front of the•

tractor as shown. Hold onto the shield as you remove

the second bolt to prevent it from falling.

NOTE: Reinstall the browning shield before using your

tractor.

INSTRUCTIONS FORTRACTORS WITH SINGLE

FRONT DECK SUSPENSION BRACKET

INSTRUCTIONS FOR 917 MODEL TRACTORS

LOCATE MODEL LABEL OF TRACTOR

Look under your tractor seat, locate the serial•

number, and proceed to the step as shown.

193653

MODEL

917. 000000

SERIAL

000000A000000

193653

MODEL

247. 000000

SERIAL

000000A000000

917 MODEL TRACTORS

GO TO PAGE 5

247 MODEL TRACTORS

GO TO PAGE 8

FIGURE 1

IDENTIFY YOUR SUSPENSION BRACKETS

Compare your tractor to the illustrations shown below.•

If your tractor resembles the top illustration, proceed•

to INSTRUCTIONS FOR TYPE A TRACTORS below.

If your tractor resembles the bottom illustration,•

proceed to INSTRUCTIONS FOR TYPE B

TRACTORS on page 7.

FRONT SUSPENSION

BRACKET

FRONT SUSPENSION

BRACKET

REMOVE BOLTS FROM THESE HOLES

FRONT

SUSPENSION

BRACKET

FIGURE 1

INSTRUCTIONS FOR TYPE A TRACTORS

STEP 1: (SEE FIGURE 1)

Remove any bolts found in the holes indicated in the•

illustration.

INSTRUCTIONS FORTRACTORS WITH DUAL

FRONT DECK SUSPENSION BRACKETS

TYPE A

TYPE B

FIGURE 3

5/16" NYLOCK

NUT (K)

3/8" NYLOCK

NUT (L)

5/16" x 1" CARRIAGE

BOLT (F)

(SEE NOTE)

ENGINE

MOUNTING

PLATE

1/2" LARGE

WASHER (M)

3/8" x 1" CARRIAGE

BOLT (H)

STEP 2: (SEE FIGURE 2)

Fasten the R.H. Side Plate (bend facing out) to the•

front three holes in the tractor frame using three 3/8"

x 1" carriage bolts (F), three large 1/2" washers (M)

(see note) and three 3/8" nylock nuts (L). For the

rear hole, use a 5/16" x 1" carriage bolt (F), a large

1/2" washer (M) and a 5/16" nylock nut (K). Place the

washers between the tractor frame and the side plate.

Tighten all bolts. Repeat for L.H. side plate.

Reinstallthebrowningshieldremovedingure2.•

Proceed to• INSTRUCTIONS FOR ALL 917 MODEL

TRACTORS on page 8.

NOTE: If there is an engine mounting plate (shown with

dotted lines) leave the large 1/2" washer (M) off the bolt

that goes through the plate.

FIGURE 2

3/8" x 1"

HEX BOLT (D)

3/8" LOCK

WASHER (R)

3/8" FLAT

WASHER (N)

1/2" LARGE

WASHER (M)

R.H. HANGER

BRACKET

STEP 2: (SEE FIGURE 2)

Attach the R.H. hanger bracket to the two front empty•

holes on the right side of the tractor frame using two

new 3/8" x 1" hex bolts (D), 3/8" lock washers (R),

and3/8"atwashers(N)asshown.Fortherearhole,

use a 3/8" x 1" hex bolt (D), 3/8" lock washer (R)

and3/8"atwasher(N)withalarge1/2"washer(M)

placed between the hanger bracket and the tractor

frame. Tighten. Repeat for the left side.

Proceed to• INSTRUCTIONS FOR ALL 917 MODEL

TRACTORS on page 8.

FIGURE 1

REMOVE BOLTS FROM

THESE HOLES

FRONT

SUSPENSION

BRACKET

INSTRUCTIONS FOR TYPE B TRACTORS

STEP 1: (SEE FIGURE 1)

Remove any bolts found in the holes indicated in the•

illustration.

STEP 2: (SEE FIGURE 2)

Attach the R.H. hanger bracket to the three holes•

shown on the side of the tractor frame using three

3/8" x 1" hex bolts (D), 3/8" lock washers (R), 3/8"

atwashers(N)and1/2"largewashers(M).Use3/8"

nylock nuts (L) on inside of frame if bolts insert freely

into holes. Tighten.

Repeat for other side.•

Proceed to• INSTRUCTIONS FOR ALL 917 MODEL

TRACTORS on page 8.

NOTE: Use special 3/8" x 1" thread forming bolts (G) in any

holes that are too small for regular bolts.

FIGURE 2

3/8" x 1" HEX BOLT (D)

(OR THREAD FORMING

BOLT (G) IF NEEDED)

3/8" LOCK

WASHER (R)

3/8" FLAT

WASHER (N)

3/8" NYLOCK NUT (L)

(IF NEEDED)

R.H. HANGER

BRACKET

1/2" LARGE

WASHER (M)

FIGURE 2

3/8" x 1"

HEX BOLT (D)

3/8" NYLOCK

NUT (L)

PIVOT SUPPORT

BRACKET

STEP 2: (SEE FIGURE 2)

Assemble the pivot support bracket to the angle•

support brackets using four 3/8" x 1" hex bolts (D)

and four 3/8" nylock nuts (L). Do not tighten yet.

Tighten• the 4 bolts fastening the angle support

brackets to the hanger brackets.

Tighten• the 4 bolts fastening the pivot support

bracket to the angle support brackets.

Proceed to• BLADE ASSEMBLY FOR ALL

TRACTORS on page 10.

STEP 2: (SEE FIGURE 2)

Assemble the pivot support bracket to the slotted•

angle support brackets using four 3/8" x 1" hex bolts

(D) and four 3/8" nylock nuts (L). Do not tighten yet.

Tighten• the 4 bolts fastening the slotted angle

support brackets to the quick attach brackets.

Tighten• the 4 bolts fastening the pivot support

bracket to the slotted angle support brackets.

INSTRUCTIONS FOR ALL 917 MODEL

TRACTORS

INSTRUCTIONS FOR 247 MODEL TRACTORS

FIGURE 1

FIGURE 2

3/8" x 1"

HEX BOLT (D)

3/8" NYLOCK

NUT (L)

ANGLE SUPPORT

BRACKET

STEP 1: (SEE FIGURE 1)

Assemble one angle support bracket to the topmost•

set of holes in the hanger brackets using two 3/8" x

1" hex bolts (D) and 3/8" nylock nuts (L). Assemble

the second angle support bracket to the second from

the bottom set of holes in the hanger brackets using

two 3/8" x 1" hex bolts (D) and 3/8" nylock nuts (L).

Be sure the brackets are turned as shown. Do not

tighten yet.

STEP 1: (SEE FIGURE 1)

Assemble one slotted angle support bracket to the•

top set of holes in the quick attach brackets using two

3/8" x 1" hex bolts (D) and 3/8" nylock nuts (L). Do

not tighten

Assemble the other slotted angle support bracket to•

the bottom set of holes in the quick attach brackets

using two /8" x 1" hex bolts (D) and 3/8" nylock nuts

(L). Do not tighten.

NOTE: Be sure brackets are turned as shown.

3/8" x 1"

HEX BOLT (D)

3/8" NYLOCK

NUT (L)

3/8" x 1"

HEX BOLT (D)

3/8" NYLOCK

NUT (L)

PIVOT SUPPORT

BRACKET

SHOULDER BOLT

ATTACHMENT PIN

FIGURE 4

STEP 4: (SEE FIGURE 4)

Pull out on the attachment pins on the hitch assembly•

and swing the top of the pins down away from the

holes they were in.

Hook the hitch assembly onto the shoulder bolts in•

the sides of the tractor frame.

Align the holes in the hitch assembly with the holes•

in the tractor frame. Insert the attachment pins to lock

the hitch assembly in place.

Proceed to• BLADE ASSEMBLY ALL TRACTORS on

page 10.

FIGURE 3

STEP 3: (SEE FIGURE 3)

Assemble a shoulder bolt (V) and a 3/8" nylock nut•

(L) to the front bracket on each side of the tractor,

unless a shoulder bolt is already present.

3/8" NYLOCK NUT (L)

SHOULDER BOLT (V)

(Right Hand Side View)FIGURE 1

STEP 1: (SEE FIGURE 1)

Assemble the two angle lock bars together as shown•

ingure6,sothatallholesarealigned.Useone3/8"

x 1-1/4" carriage bolt (E) and one 3/8" nylock nut (L).

Be sure to insert bolt from side indicated. Do not

tighten at this time.

Hold the angle lock bars so that the square holes are•

at the top. Insert the straight hook end of the angle

lock spring through the small middle hole in both

angle lock bars.

3/8" x 1-1/4"

CARRIAGE BOLT (E)

3/8" NYLOCK NUT (L)

ANGLE LOCK BARS

ANGLE LOCK

SPRING

STEP 2: (SEE FIGURE 2)

Insert the round hook end of the angle lock spring up•

through the hole in the spring mount bracket.

Insert the angle lock bars down through the slot in the•

channel. Underneath the channel, place a 1" long spacer

(U) on each side of the angle lock bars and insert a 1/4"

x 3-1/4" bolt (A) through the channel, angle lock bars

and the spacers. Secure the bolt with a 1/4" nylock nut

(J). Tighten so that lock bars can pivot freely.

At this time• tighten the 3/8" carriage bolt and hex nut

previously assembled to angle lock bars.

NOTE: When the angle lock bars are pulled back in slot,

the pivot plate should unlock and be free to pivot to the

right or left position.

1/4" x 3-1/4"

HEX BOLT (A)

1" SPACERS (U)

1/4" NYLOCK

NUT (J)

PIVOT

PLATE

ANGLE

LOCK

SPRING

MOUNT

BRACKET

CHANNEL

(Right Hand Side View)FIGURE 2

(Top View)

FIGURE 3

STEP 3: (SEE FIGURE 3)

Using a hammer, assemble a 3/8" palnut (S) onto one•

end of the spring mount rod. Insert the other end of

the spring mount rod through the pivot plate using the

rear set of holes. Support the assembled end of the

spring mount rod on a block of wood, and assemble

the remaining palnut onto the other end of the rod.

3/8" PALNUT (S)

PIVOT

PLATE

SPRING

MOUNT

ROD

3/8" PALNUT (S)

STEP 4: (SEE FIGURE 4)

Assemble a 3/8" x 1-1/4" carriage bolt (E) through•

the square hole in the cable mount bracket and

through the square hole in the angle lock bars. (The

carriage bolts should face in opposite directions.)

Using pliers hold the cable mount bracket in position,

angling down towards the L.H. hole in the channel as

showningure15.Securewitha3/8"nylocknut(L).

Tighten.Refertothegureforthecorrectanglefor

the cable mount bracket.

FIGURE 4 (Right Hand Side View)

3/8" x 1-1/4"

CARRIAGE BOLT (E)

3/8" NYLOCK

NUT (L)

ALIGN CABLE

MOUNT BRACKET

WITH L.H. HOLE ANGLE

LOCK

BARS

FRONT

BLADE ASSEMBLY FOR ALL TRACTORS

Inhaltsverzeichnis

Andere Craftsman Rasen- und Gartengeräte Handbücher

Craftsman

Craftsman 917.248930 Bedienungsanleitung

Craftsman

Craftsman 247.24019 Bedienungsanleitung

Craftsman

Craftsman 358.796355 Bedienungsanleitung

Craftsman

Craftsman 247.240193 Bedienungsanleitung

Craftsman

Craftsman 19A30041791 Bedienungsanleitung

Craftsman

Craftsman Incredi-Pull 316.794450 Bedienungsanleitung

Craftsman

Craftsman CMCW211 Bedienungsanleitung

Craftsman

Craftsman C944.514323 Bedienungsanleitung

Craftsman

Craftsman 610.240842 Betriebsanleitung

Craftsman

Craftsman 358.797110 Bedienungsanleitung

Craftsman

Craftsman 486.24250 Bedienungsanleitung

Craftsman

Craftsman 320.74900 Bedienungsanleitung

Craftsman

Craftsman 358.795620 Bedienungsanleitung

Craftsman

Craftsman 0944.511590 Bedienungsanleitung

Craftsman

Craftsman 358.795631 Bedienungsanleitung

Craftsman

Craftsman 486.24116 Bedienungsanleitung

Craftsman

Craftsman 486.24839 Bedienungsanleitung

Craftsman

Craftsman 29281 Bedienungsanleitung

Craftsman

Craftsman 610.24600 Bedienungsanleitung

Craftsman

Craftsman 358.796370 Bedienungsanleitung

Craftsman

Craftsman 358.795660 Bedienungsanleitung

Craftsman

Craftsman 486.244021 Bedienungsanleitung

Craftsman

Craftsman 944.361065 Bedienungsanleitung

Craftsman

Craftsman 486.243001 Bedienungsanleitung

Beliebte Rasen- und Gartengeräte Handbücher anderer Marken

Vertex

Vertex 1/3 HP Technische Daten

GHE

GHE AeroFlo 80 Bedienungsanleitung

Millcreek

Millcreek 406 Bedienungsanleitung

Land Pride

Land Pride Post Hole Diggers HD25 Bedienungsanleitung

Yazoo/Kees

Yazoo/Kees Z9 Commercial Collection System Z9A Programmierhandbuch

Premier designs

Premier designs WindGarden 26829 Bedienungsanleitung

Snapper

Snapper 1691351 Bedienungsanleitung

Mosquito Magnet

Mosquito Magnet Patriot Bedienungsanleitung

Perfect

Perfect BG2 Bedienungsanleitung

P.Lindberg

P.Lindberg LS2 Bedienungsanleitung

Gardena

Gardena Easy 1887 Bedienungsanleitung

Makita

Makita UM104D Bedienungsanleitung

AQUA FLOW

AQUA FLOW PNRAD Bedienungsanleitung

Tru-Turf

Tru-Turf RB48-11A Golf Green Roller Benutzerhandbuch

BIOGROD

BIOGROD 730710 Bedienungsanleitung

Land Pride

Land Pride RCF2784 Bedienungsanleitung

Makita

Makita UM110D Bedienungsanleitung

BOERBOEL

BOERBOEL Standard Floating Bar Gravity Latch Bedienungsanleitung