Craftsman 610.24600 Bedienungsanleitung

User Instructions

IRA

TRACTOR LIF

Model Number 610.24600

Provides access to mower deck for easy

cleaning and service

Fits all 1985 through current models

of CRAFTSMAN front engine tractors

and Zero Turn Mowers

Can be fitted to most major front engine tractor brands

Adjustable arms for greater versatility

Extra heavy duty gauge steel construction

If you read and follow these instructions, this product can be

assembled in approximately 20 minutes

Assemble unit on cardboard to avoid scratches or damage to parts

Can easily be assembled by one person

All fasteners for this Tractor Lift can be purchased at Sears or any

hardware store

Patent Pending

If there are any missing

parts, or if you have any

questions on assembly,

operation, maintenance

or safety, please call

1-800-652-6231

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Visit our Craftsman website: www.sears.com/craftsman 610.24600-REV B 3/08

WARNINGS

• Always use the stabilizer bar provided when using tractor lift.

Make sure stabilizer bar is properly in place before starting any

work on tractor.

• Read and understand all safety and operating instructions

before using the tractor lift. Never allow anyone unfamiliar

with these instructions to use the tractor lift.

• Read and understand all safety and operating instructions

provided by the tractor's manufacturer before using tractor lift.

• Never lay under the tractor or mowing deck.

• When using lift, keep all bystanders, including children, away.

• This tractor lift must be only used for lifting and lowering to

and from a level and stable surface.

• Never use in wet conditions.

• Do not attempt to lift the front and back of the tractor at the same

• Do not use tractor lift as an automotive lift, or for any other use for

whist is not intended or designed.

• If tractor lift is bowing while lifting or lowering your tractor, which

indicates an overload condition, remove the tractor immediately.

• Do not attempt to lift or lower any power equipment while motor is

running.

• Never engage blades while using tractor lift.

• Always disconnect spark plug wire from tractor before beginning

any work on tractor.

• Do not exceed the rated capacity of the tractor lift - 270#.

• Failure to follow these warnings may result in property

damage and/or serious bodily injury.

SAFETY INSTRUCTIONS

• Be sure to read and follow all safety instructions and

warnings. Failure to follow these instructions may result in

damage to the product and/or serious personal injury.

• Danger of serious personal injury exists. Serious personal

injury can occur when using a lifting device.

• Never attempt to ride any vehicle up or down the tractor lift.

• Do not climb onto tractor while tractor is in the elevated position.

• When working on the front of the tractor always place wheel

chocks in back of the rear wheels/tires.

• Always raise and lower tractor lift in a controlled fashion; do not

allow the tractor to drop too quickly, damage could occur.

• Make sure lifting arms are aligned and set to the proper distance apart

so that the equipment being loaded is well balanced on the lift.

• Do not remove warning decals from product.

• Before each use, always check for any worn, loose, or

damaged parts on the tractor lift. If any damage is present,

DO NOT USE THE TRACTOR LIFT.

• Periodically check the fasteners to make sure they are still

tight and in place.

• Keep lift surface clean by occasionally cleaning with water and

any mild detergent.

• Do not add to or try to modify the tractor lift in any way.

Any modifications will void any warranties.

• Failure to abide by the warnings and read the safety instructions may

result in loss of load, damage to lift and/or property, serious personal

and/or fatal injury.

FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m.E.S.T.

Page 2.

Carton Contents

;:.C_L&C:.C,:.............. _

6-...% 1 lO

REF NO QTY PART NUMBER DESCRIPTION REF NO QTY PART NUMBER DESCRIPTION

1 1 51001 Angle Frame Assembly 7L 1 410131 Tractor Mounting Bar - Left

2 1 51002 Handle Top 7R 1 410132 Tractor Mounting Bar- Right

3 1 51003 Handle Bottom 8 1 51006 Stabilizer Bar

4 2 41009 Lift Tube Assembly 10 1 310031 Hardware Bag

6 1 51005 Lift Cross Tube 11 1 310041 Assembly Manual

OPERATION

Tractor Lift can be used out of the box on all Craftsman tractors

with bumpers or brush guards. Tractor Lift mounting hardware is

provided if your tractor does not have a bumper or brush guard.

TOOLS REQUIRED FOR ASSEMBLY

9/16" Wrench and/or Socket

Adjustable wrench

MAINTENANCE

Store unit in a clean dry place.

Recommended tire pressure - 30 PSI.

Before each use:

• Always check tire pressure.

• Always inspect unit for damage.

• Always check fasteners for tightness.

FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m.E.S.T.

Page 3.

Hardware Contents

m 29

_-I 33

m22

r-'-

-iiliiliiliiliiliiliiliiliililil

c,__

REF NO

QTY

PART NUMBER

310051

310072

310073

310062

300082

310061

310054

DES ORIPTI ON

3/8"-16 x 2-3/4" Hex Bolt

3/8" Split Lock Washer

3/8" USS Flat Washer

3/8"-16 Hex Nut

Hair Pin Cotter .148 Dia.

3/8"-16 l',,_ylokHex Nut

3/8"-16 x 1-1/2" Self-thread Bolt

REF NO QTY

29 6

33 1

34 4

35 4

36 4

37 2

38 4

39 1

PARTNUMBER

310055

310053

310052

310065

310075

310182

310221

31026

DESCR I PTION

3/8"-16 x 1-1/4" Hex Bolt

318"-16 x 2-1/4" Hex Bolt

1/4"-20 x 1" Hex Bolt

1/4"-20 l'¢/Iok Hex Nut

1/4" USS Flat Washer

Vinyl Handle Grip

Tube Plug RT8-1

Scuff Pad

FOR MISSING PARTS, Cattl-800-652-2321, Monday-Friday, 8 a.m.-5 p.m.E.S.T.

Page 4.

Setting up Lift Mounting Hardware -Tractor Front

Tractor Lift can be used out of the box on all Craftsman tractors with bumpers or brush guards. Tractor Lift mounting hardware is provided. If

your tractor does not have a bumper or brush guard, follow the steps below:

Note: Left and Right sides are determined by standing behind tractor looking forward.

Remove,

add washer (24),

Step 1. replace.

Step 2.

6 %38

Step ,

Remove existing bolt "X" and set aside. If tractor does not have

this bolt use supplied 3/8" x 1-1/4" bolt with 3/8 nylok nut.

Align holes in tractor mounting bars ( 7R & 7L ) to the front

left & right side frame holes of the tractor.

Insert hex head bolt ( 29 ) through inside front hole of frame,

through tractor mounting bar and secure with nylock nut ( 27 ).

Add flat washer ( 24 ) under head of bolt removed in earlier

step and reinsert through tractor mounting bar and tighten.

For LT1000 & LT2000 series tractors, use self-thread bolts

( 28 ) in place of bolt ( 29 ) and nut ( 27 ).

Step 2.

• Push tube plugs ( 38 ) into each end of lift tube ( 6 ).

Slide lift tube through cut-out in tractor mounting bars and

center.

Pin lift tube in place with one hair pin cotter ( 26 ) on each side

of mounting bar.

Note: The mounting bars have been manufactured to attach to the

frames of most major front engine tractor brands. Additional

hardware has been included for attachment to non-Craftsman

brands.

FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m.E.S.T.

Page 5.

Assemble Tractor Lift

Attach Lift Tubes to Angle Frame

• Lift tubes come pre-assembled. Attach lift tube assemblies ( 4 ) to angle frame ( 1 ) using bolts ( 22 ), flat washers ( 24 ), split lock washers ( 23 )

and hex nuts ( 25 ).

• Secure rear of lift tube assembly ( 4 ) to angle frame ( 1 ) using bolts ( 29 ), flat washers ( 24 ), split lock washers ( 23 ) and hex

nuts ( 25 ).

Note: Over-tightening receiver bolts ( 22 ) could cause damage to lift tubes ( 4 ).

Determining the width between lift tubes.

Front of Craftsman Tractors

Front of Craftsman Zero Turn

/25

Brush guard bumper

(can also be used for

front of Craftsman tractor)

Push mower

-4

Note: The higher the lift tube extensions (5)

are positioned, the harder the tractor will be to lift.

oo o o

DCB A A BCD

Settings:

A. Push Mower

Brush guard /Bumper installed

Front of Craftsman Tractor

Front of Craftsman Zero Turn

FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m.E.S.T.

Page 6.

Assemble Tractor Lift

Attach Handle to Angle Frame

Step 1. Attach handle bottom ( 3 ) to angle frame ( 1 ) using hex bolt ( 22 ),

flat washer ( 24 ), split lock washer ( 23 ) and hex nut (25).

Step 2.

Step 3.

Step 4.

Insert ring grip pin ( 30 ), as shown.

Insert handle top ( 2 ) into handle bottom ( 3 ). Secure with hex

bolt ( 33 ), flat washer ( 24 ), split lock washer ( 23 ) and hex nut (25).

Place handle grips ( 37 ) onto handle top tube ( 2 ). A little

soapy water will help grip slide onto tube easily.

IF HANDLE CANNOT BE

EASILY INSERTED, FLIP

HANDLE OVER AND

REINSERT,

j37 3

Handle Top Tube -j

Foot Bar Tube

FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m.E.S.T.

Page 7.

Assemble Tractor Lift

Attach Stabilizer Bar

Step 1. Slide stabilizer bar ( 8 ) onto foot bar tube as shown.

Step 2. Press snap button and slide stabilizer bar against handle.

Step 3. Insert ring grip pin ( 30 ) through stabilizer bar and handle top.

Foot bar

Snap

FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m.E.S.T.

Page 8.

OPERATION

Using the Tractor Lift

Step 1. Engage Tractor Lift

• Center Tractor Lift in front of tractor.

, Ensure that claws at ends of lift

tubes are securely hooked under

the lift cross tube attached to tractor

(Figure 1) or to the tractor

bumper/brush guard (Figure 2.)

Figure !.

Properly engaging tractor

with mounted lift cross tube.

Figure 2.

Properly engaging tractor

with tractor bumper/brush guard.

Step 2. Lift Tractor

• Place foot onto foot bar tube and apply

continuous forward pressure with foot

while pulling down on tractor lift handle.

• Once lifted, the weight of tractor will

automatically force handle down

into correct position.

IMPORTANT: Stabilizer bar MUST be engaged

immediately after raising the tractor. See Step 3

on next page for instructions.

FOR MISSING PARTS, Call 1-800-652-2321, Monday-Friday, 8 a.m. - 5 p.m. EST.

Page 9.

OPERATION

Using the Tractor Lift

Step 3. Engaging Stabilizer Bar

Stabilizer bar MUST be engaged immediately after raising the tractor.

WARNING: Failure to engage stabilizer bar may result in serious personal

injury and or property damage.

• Remove ring grip pin ( 30 ) from tube handle. Press snap button

and slide stabilizer bar ( 8 ) from foot bar tube.

• Turn stabilizer bar 180 degrees as shown at bottom of Figure 1.

• Position stabilizer bar under base of unit between wheels.

• Slide stabilizer bar back onto foot bar tube making sure the bar is

positioned back over snap button.

--Tube Handle

Snap

Figure 1

Figure 2

Snap Button

FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m.E.S.T.

Page 10.

Inhaltsverzeichnis

Andere Craftsman Rasen- und Gartengeräte Handbücher

Craftsman

Craftsman 917.248950 Bedienungsanleitung

Craftsman

Craftsman 842.242560 Bedienungsanleitung

Craftsman

Craftsman ZTS 7500 Bedienungsanleitung

Craftsman

Craftsman 421264 Bedienungsanleitung

Craftsman

Craftsman 486.24560 Bedienungsanleitung

Craftsman

Craftsman 610.24610 Bedienungsanleitung

Craftsman

Craftsman 917.248961 Bedienungsanleitung

Craftsman

Craftsman 41AJSS-C799 Bedienungsanleitung

Craftsman

Craftsman 486.24441 Bedienungsanleitung

Craftsman

Craftsman 610.240842 Betriebsanleitung

Craftsman

Craftsman CompuCarve 183.217540 Bedienungsanleitung

Craftsman

Craftsman 358.795792 Bedienungsanleitung

Craftsman

Craftsman 358.795631 Bedienungsanleitung

Craftsman

Craftsman 486.24449 Bedienungsanleitung

Craftsman

Craftsman 316.792570 Bedienungsanleitung

Craftsman

Craftsman 358.795630 Bedienungsanleitung

Craftsman

Craftsman 358.797110 Bedienungsanleitung

Craftsman

Craftsman 486.243291 Bedienungsanleitung

Craftsman

Craftsman 917.249040 Bedienungsanleitung

Craftsman

Craftsman ZT 7000 Bedienungsanleitung

Craftsman

Craftsman 757.242330 Bedienungsanleitung

Craftsman

Craftsman 316.792410 Bedienungsanleitung

Craftsman

Craftsman 486.244411 Bedienungsanleitung

Craftsman

Craftsman 486.24839 Bedienungsanleitung

Beliebte Rasen- und Gartengeräte Handbücher anderer Marken

Vertex

Vertex 1/3 HP Technische Daten

GHE

GHE AeroFlo 80 Bedienungsanleitung

Millcreek

Millcreek 406 Bedienungsanleitung

Land Pride

Land Pride Post Hole Diggers HD25 Bedienungsanleitung

Yazoo/Kees

Yazoo/Kees Z9 Commercial Collection System Z9A Programmierhandbuch

Premier designs

Premier designs WindGarden 26829 Bedienungsanleitung

Snapper

Snapper 1691351 Bedienungsanleitung

Mosquito Magnet

Mosquito Magnet Patriot Bedienungsanleitung

Perfect

Perfect BG2 Bedienungsanleitung

P.Lindberg

P.Lindberg LS2 Bedienungsanleitung

Gardena

Gardena Easy 1887 Bedienungsanleitung

Makita

Makita UM104D Bedienungsanleitung

AQUA FLOW

AQUA FLOW PNRAD Bedienungsanleitung

Tru-Turf

Tru-Turf RB48-11A Golf Green Roller Benutzerhandbuch

BIOGROD

BIOGROD 730710 Bedienungsanleitung

Land Pride

Land Pride RCF2784 Bedienungsanleitung

Makita

Makita UM110D Bedienungsanleitung

BOERBOEL

BOERBOEL Standard Floating Bar Gravity Latch Bedienungsanleitung