Craftsman 757.242330 Bedienungsanleitung

MODEL NO.

757.242330

Caution:

Read Rules for

Safe Operation

and Instructions

Carefully

- i n,,lU,,,i ,,iru,,_l

10qNCH

MOLDBOARD PLOW

FOUR 55 POUND WHEEL WEIGHTS, ONE FRONT WEIGHT

BRACKET, AND A SLEEVE HITCH ACCESSORY ARE RE-

QUIRED FOR OPERATION ALSO, TIRE CHAINS ARE

RECOMMENDED

®Assembly

® Installation

®Operation

®Repair Parts

,,it, i ,n .............. inlll,l,l,,, '11' 1: ilU,irll nl, .....................

L-1222 SC Sears, Roebuck And Co, Hoffman Estates, tL 60179, USA,

ilU,i i,i ,,,lit i lU................... i lU,l,, i lUUl i

LIMITED ONE YEAR WARRANTY ON MOLDBOARD PLOW

For 1 year from the date of purchase, when this Moldboard Plow is maintained

and lubricated according to the operating and maintenance instructions in

the owner's manual, Sears will repair, free of charge, any defect in material

or workmanship..

This warranty does not cover:

---repairs necessary because of operator abuse or negligence including the

failure to maintain the equipment according to instructions contained in

the owner's manual; and Moldboard Plow used for commercial or rental

purpose&

WARRANTY SERVICE tS AVAILABLE BY RETURNING TO THE NEAREST

SEARS SERVICE CENTER/DEPARTMENT IN THE UNITED STATES. This

warranty applies only while this product is in use in the United States°

This warranty gives you specific legal rights and you may also have other

rights which vary from state to state.

SEARS, ROEBUCK AND COo, D/8t7 WA, Hoffman Estates, IL 60179, U.S.A.

RULES FOR SAFE OPERATION

e Know controls and how to stop quickly, READ THE e Keep the vehicle and attachment

OWNER'S MANUAL

e Do not allow children to operate the vehicle, do

not allow adults to operate without proper

instruction and without having read the owner's

manual.

o Do not carry passengers Keep children and pets

a safe distance away

Always wear substantial footwear. Do not wear'

loose fitting clothing that can get caught in

moving parts

® Keep your eyes and mind on your tractor/attach-

ment and area being covered Don't let other

interests distract you

e Stay alert for holes in the terrain and other

hidden hazards

in good operating

condition and keep safety devices in place.,

e Keep ail nuts, bolts and screws tight to be sure

the equipment is in safe working condition,

eThe vehicle and attachment should be stopped and

inspected for damage after striking a foreign

object. The damage should be repaired before

restarting and operating the equipment

®See tractor equipment owner's manual for safe

operation of the equipment.

o Do not drive close to creeks, ditches and public

highways

o Watch out for traffic when crossing or near

roadways.

® When using any attachment, don't allow anyone

near the vehicle while in operation

WARNING !!!

e Plow share and coulter blade edges are sharp!!!

Wear gloves when handling

Always LIFT the plow before turning!!

e Lock Tractor Lift Handle down when installing

or removing plow!

i& ................ I

LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT

SAFETY PRECAUTIONS,. tT MEANS * ATTENTION!

BECOME ALERT! YOUR SAFETY IS INVOLVED.

H in u n nH i .....................

CONGRATULATIONS on your purchase of a Sears Craftsman 10" Moldboard Plow It has been designed,

engineered, and manufactured to give you the best possible dependability and performance

Should you experience any problem you can not easily remedy, please contact your nearest

Sears Service Center/Department We have competent, well trained technicians and the proper

tools to service or repair your PLOW

Please read and retain this manual The instructions will enable you to assemble and maintain

your Plow properly Always observe the "SAFETY RULES"

o THE MODEL AND SERIAL NUMBERS WILL BE

FOUND ON A DECAL ATTACHED ON THE

SIDE OF THE PLOW BEAM

e YOU SHOULD RECORD BOTH SERIAL NUMBER

AND DATE OF PURCHASE AND KEEP IN A

SAFE PLACE FOR FUTURE REFERENCE

CUSTOMER RESPONSIBILITIES

e Read and observe the "SAFETY RULES",,

e Follow a regular schedule in maintaining, caring for

and using your Plow.,

TABLE OF CONTENTS

WARRANTY ..............................................................2 PLOWING TIPS......................................................8

SAFETY RULES ........................................ 2 ADJUSTMENTS ........................................... 8 & 9

CARTON CONTENTS ........................... 3 & 4& 5 CUSTOMER RESPONSIBILITY ....................... 9

ASSEMBLY .................................................... 5&6 TROUBLE SHOOTING ................................. !0

OPERATION ...........................................................7&8 REPAIR PARTS ............................................... 11

CONTENTS OF SHIPPING CARTON

No A L-1222SC

Literature

t Used

No 13 P_260_01

Crank

1 Used

No B Z-1216-A No C Z-1216-B

Hardware Bag Hardware Bag

No 18 P-272A-10

Cou_ter Blade

1 Used

No 8 P-250A

No D Z-I216-C Coulter Hub

Hardware Bag 1 Used

No 10 P-254-10

Beam Half

2 Used

Landside

1 Used

No 12 P-257-10

Hitch Bracket

t Used

No 16 P-269A-10

Coulter Standard

_ 1 Used

No E P-566-t0

10 Plow

! Used

No 25 P-596-10

Adiusting Bracket

2 Used

No 9 P-251_10

Standard

1 Used

No 11P-256P

Threaded Tube

1 Used

No 15 P-265A-t0

Fork

1 Used

Nu 1 Bo]674P

Hex ILocM Nut 5/16

3 Used

No 3 B-1678F _

Hex (Lock) Nut 5/8

2 Used

No 3g 30M2000P

Hex Nut 5/8

2 Used

Z-1216-A HARDWARE BAG

No 26 P-597

Spacer

5/8t D x 1/2

2 Used

No 28 1M1624P

Hex Head Boft

t12 x 1-1/2'

2 Used

No 35 15Mt632P

No 29 1M1628P Plow Bolt

Hex Head Bo_t 1t2 x 2'

1/2' x 1_3/4" 1 Used

2 Used

No 42 45Mtl11P No 44 45Mt717P No 45 45M2121P

Fiat Washer 5116' Flat Washer 1/2 Flat Washer 5/8

3 Used 1 Used 2 Used

Z-1216-B HARDWARE BAG

No 7 P_234

Spacer

II2 tD xgi16

! Used

No 14 P-262-01

Spacer

5/8'1D × 518

1 Used

No 2 B.t677P

Hez{Lockl Nut 1 2

3 Used

No 33 I5M1216-R No 31 10M1012P

No 17 P-270 PIow Bolt Carriage Bolt No, 32 10MI624P

Drive Pin 3/8 x I 5/16" x 3/#', Carriage 8olt

5/16 "xlqi4 2 Used 3 Used 1/2"x!"1/2"

1 Used t Used

No 38 30M1600P

Hex Nut 1t2" i__,,_ No 41 35M1600P

2 Used _ Square Nut t/2

No 40 31M2000P

He× (Jam} Nut 5z8

2 Used

No 36 3OMI200P

He× Nut 3 8

2 Used

No 30 1M2032P

Hex Head Bolt

5/8x 2'

2 Used

No 46 50M0420P

Cotter Pin

1/8 × 1_1/4

1 Used

NO 24

Coulter Clamp

Used

Z-1216-C HARDWARE BAG

No 6 P-172P

Coulter Axle O

1 Used.

No 23 P-386P

"U" Bolt

1 Used

ASSEMBLY

NOTES

o IT IS RECOMMENDED THAT YOU CAREFULLY READ THIS

OWNER'S MANUAL BEFORE STARTING ASSEMBLY OF THE UNIT

g Before starting assembly, arrange each kind of

hardware into a group to ease assembly

g Right hand (RH.) and left hand (LH) are determined

from the OPERATOR'S position while seated on the tractor.

IMPORTANT-Mower Deck must be removed when

using Plow to avoid damage to your Deck.

PLOW FRAME

Refer to Fig 1

NOTE: Securely tighten all fasteners ONLY after Plow

assembly has been completed, unless noted otherwise

g Assemble the two adjusting brackets to the inside

of both beams using one t/2"x 1-3/4 '' hex bolt and

one 1/2" hex lock nut

a Slip trunnion through the hote in each adjusting

bracket and insert crank through the hole in

"SIDE"of trlJnnion, through spacer, the two 5/8"

jam nuts, and then thread into the threaded tube,,

e Thread one jam nut against the spacer just enough

to eliminate any excessive movement of the crank

against the trunnion, taking care NOT to bind crank

o Using two wrenches, lock the other jam nut

against the first

e Before assembling the hitch bracket BETWEEN both

beams refer to the chart'and measure the distance

BETWEEN the rear wheels on your tractor for the

proper position of the bracket,

Distance

Between

Rear Tractor

Wheels (inches)

16-19

19-2!

21-23

Over 23

Use Hole #

TABLE 1

Tools Required For Assembly:

1-10" Adjustable Wrench

1- 15/16" Wrench

1_13/t6" Wrench

1- 3/4" Wrench

1-Pair of pliers

1- t/2" Wrench

1-9/16" Wrench

1 - Pair Gloves

(Leave modal

plate OUtside)

5/8" ID x5/8" Spacer

_Jnnion Crank

3L 2L IL

FOP VIEW -WITH HITCH BRACKET

ASSEMBLY TO LEF_..._TSIDE TOP VIEW -WITH HITCH BRACKET

ASSEMBLY TO RIGHT SIDE

FIG I

g Secure with two 5/8"x 2" hex bolts and 5/8" hex 5

lock nuts

PLOW BOTTOM AND STANDARD

Referto Fig.2

@Assemblethelandsideto frog usingtwo 3/8"x 1"

plowboltsand 3/8" hexnuts.

@Attachstandardto frogusing1/2"x2" plowbolt

and 1/2"hexnutasshown,

andstandardandsecurewith a 1/2"hexnut.

@Insertone1/2"x I-1/2" HexBott(Tracking

AdjustingBolt)throughthe "tab"atthebottom

of standard.Placethe 1/2" Squarenutbetween

the'q'ab"andFrog,andthreadtheTracking

AdjustingBoltintothesquarenut untiltight,

Tightenall fastenerssecurely.

PLOW FRAME AND BOTTOM (Refer to Fig 3]

e Straddle the beams over standard and fasten together

at the LOWER hole in the standard with one 1/2"x 1-3/4"

bolt and 1/2" hex lock nut

e Attach end of threaded tube to side of standard at

the UPPER hole with a 1/2"x 1-1/2" hex bolt followed by

the 1/2" flat washer, then place the 9/16"spacer in the

hole in standard and secure this assembly with one 1/2"

hex lock nut

e Tighten these fasteners so that the threaded tube is

free to pivot

COULTER BLADE (Refer to Fig 4]

e Insert coulter standard into fork, align the holes and

drive the 5/t6"x 1-1/4" pin through, leaving an equal

amount of pin on each side

e Attach the coulter hub to the coulter blade using

three 5/16"x 3/4" carria£;e bolts, 5/16" flat washers, and

5/16" lock nuts

e Install the coulter blade on the fork by inserting

the axle through one leg of the fork, the coulter

hub, and other leg of fork, Secure with the two 5/8" flat

washers and 1/8"x 1-1/4" cotter pin, bend the legs over°

e Attach the coulter assembly to the plow beam as

shown, using the "U" bolt, coulter clamp, two spacers

(locate BETWEEN the plow beams), and secure with two

5/8" hex nuts

Q Position the coulter standard between the "U" bolt and

coulter clamp and move up to the highest position

eRefer to the coulter adjustment section for proper set-

ting, to be adjusted AFTER you begin plowing,

_ WARNING

O The "Attachment Clutch" Switch on dash of Tractor

(device that engages Tractor Mower) needs to be

ENGAGED at afl times while operating Tractor This

actuates the Operators Sensing Device in the Tractor

seat ---Tractor Engine wil! stop in case you dismount

or fall off Tractor Failure to actuate this device

can cause personae injury or damage to your Tractor

and Property if you were to fatl off, SWITCH MUST BE

DISENGAGED IN ORDER TO RESTART ENGINE!

1/2" x 2" Ptow bott 1/2"X1-1/2"

Carriage bolt Standard

Landside

1/2" Square nut

1/2"× 1-1

He× bolt- !/2"Hex nut

(Tracking Ad

3/8" Hex nuts

FIG 2

Threaded tube

Standard ___.. Crank

1/2"1D x9/16 Spacer

l/2' .I_-_,. 1/2- Lock nut

Fiat washer

1/2"x 1-t/2'

Hex Bolt

tube

1/2" Lock nut

1/2" x 1-3/4"

Hex Bolt Lower hole in standard

FIG. 3

5/8"1D × 1/2" Spacers _'l "U" Bolt

Ptew Beam _'_'_- ""_©

5/16"X3/4" Carriage bott -Coutter

clamp

5/16" Locknut

Cotter pin

Coulter standard

I/8 5/t6 x t-1/4" Pin

Flat wa,sher Coulter fork

_-_ Coulter blade

FIG. 4

OPERATION

PREADJUSTMENT [Refer to Fig. 5 and 6]

Note: During normal plowing, the right side Tractor Wheels

will be riding in the previously plowed furrow A furrow

is the cut area your plow makes when turning the soil,

An initial setting for your plow is required to cut the

first furrow on level ground The following pre-sets will

result in an approximate 5" to 6" plowing depth,,

Remove Stabilizer Bolts and Nuts from Sleeve Hitch

The plow must be free to move side to side on Hitch

Lower your Tractor Lift Handle and lock in Lowered

Position. You may need to Lower the "Attachment Depth

Control" on your Tractor to do this

e Mount the Plow to the Sleeve Hitch with the Hitch Pin

furnished with the Hitch Refer to Figure 1 and Table 1 to

select the proper mounting hole

e Adiust Lift Spring Tension on Hitch as required, see

Hitch Manual for instructions

e Adjust the Depth Crank of Plow until Point of

Plow Share is on the ground and the rear of Plow

Landside is approximately 1" off the ground. (Refer

to Figure 5)

Note: The Plow will appear to be angled to left,

This will allow the Plow to run level when the

Right Hand Tractor Wheels are in the plowed furrow°

eThe plowing depth is set by adjusting the

Tractor Sleeve Hitch Turnbuckle until Hitch Drawstrap

has about I" of slot exposed between Pin and end

of Slot. Loosen the Hex Nut on the Hitch

Turnbuckle to adjust it Make sureto retighten it

after adjusting

eAdjust the Plow Coulter to its highest position,

e Go and make your first two furrows as described

in the diagram (X to A and turn B to C )., Make

sure the Tractor Lift Handle is Lowered and Locked

into the down position. Plow in Third Gear and near

Full Throttle Raise the Plow to the Transport

Position when turning

e If your Plow is not plowing at 4"to 5" deep

on your initial two passes, readjust the Plow Depth

Crank by turning it clockwise (.,-e.) to go deeper

or counter-clockwise (.e_) to go shallower. (See

Fig 8) Make this adjustment ONE TURN at a time

until desired depth is obtained,

Note: The rest of the furrows will be made with

the Tractor Tires in the previously cut furrows;

therefore, the Pitch (Depth) of the Plow must be

readjusted to a 5" to 6" plowing depth,

Position your Tractor with the inside of the

Right (Side) wheels against the side of the

previously plowed furrow

Start plowing for a short distance and check the

depth of the furrow Adjust the Depth Crank Clock-

wise or Counter-Clockwise ONE turn at a time and

retry until the 5" to 6" depth is obtained

FIG,. 6

e After plowing depth is set with plow in furrow,

stop the Tractor and measure the distance from the

centerline of the Plow Coulter Axle Bolt---it

should be about 2"above the ground If it is not,

raise the Plow out of the ground and adjust the

Coulter up or down to obtain this dimension Be

sure to adjust side motion at thistime (See

Coulter Adjustment page 8)

TRACKING ADJUSTMENT (OPTIONAL)

Note: If the Plow appears to track to the left Standard and turning the Tracking Adjustment Bolt

while plowing, an adjustment is available to correct Clockwise ("_') two turns,, Retighten Hex Nuts

this condition (Refer to Figure 9) securely, Repeat Adjustment as necessary until plow

®The Tracking Adjustment is made by loosening both pulls straight at !0" from the adjacent plowed

.].[2" Hex .Nuts spcuring the Plow Bottom to the 7 swath

eHighweedsor grassmustbecut downwitha

rotarymowerbeforeplowing,

e NEVERplowwhensoilis wet+A ruleof thumb

istopickup a handfulof soil androll it into

a "ball" If soildoesnotcrumble,it is too

wet,,tf thesoilistoo dry,it maybe difficult

for theplowto penetrateproperly

eAvoidlowareas,old roadways,paths,andother

placeswhere soil is overly packed

e Expect to have some difficulty plowing+ thick

sod, However, by using the proper settings for

Coulter, Hitch, and Crank, you should be able to

do a good job under most conditions,+

® Do not tighter+ Stabilizer Bolts, the plow must

be free to sway from side to side, (Refer to your

Hitch Manual)

o Your 10" Plow will generally work best at a

depth of 5 to 6 inches

PLOWING TIPS

Lay out your field to be plowed, and if

possible make it rectangular in shape

Note: It is easier to plow a few long furrows

than many short ones, Leave some room at each

end of the field for turning your tractor,

e ALWAYS LIFT THE PLOW BEFORE TURNtNGttt

eDo not plow too fast! Move steadily along so

that the earth will turn over and not fall back

into the furrow, In most soils, this is done at

FULL THROTTLE in Third Gear+

Note: If Plowing Speed changes, it may be

necessary to re-adjust the Depth Crank to maintain

desired plowing depth+

e In light soils, plowing may often be done in a

higher Gear, but if you travel too fast, the

furrows will be uneven and the dirt is apt to be

thrown rather than rolled over,+

TRACTION

eFour 55 lb weights are required Refer to diagram

for positioning them See your local Sears Store or

Catalog outlet for purchase of weights,

e Tire Chains: Tire Chains or Rear Chevron Tires

(Agricultural Tires) are also recommended with the

plow Again, see your local Sears Store or Catalog

Outiet or refer to your Tractor Owner's Manual for

tire size

e When plowing heavy clay soil or sod, it will

help to reduce the width of the plow cut, This

can be accomplished by hitching the plow one or

two holes to the LEFT of the recommended setting,

(Refer to Fig 1)

2-55 Pound Wheel Weights

1-55 Pound Wheel Weight

and Front Weight Bracket

Set Of Tire Chains

1* 55 Pound Whee4 Weight

ADJUSTMENTS

COULTER ADJUSTMENT

Refer to Fig 7

eThe coulter should be adjusted to slice 2"to 3"

deep when plow is in the ground Make this

adjustment by loosening the two hex nuts which

secure the "U" bolt and then move the coulter

assembly standard up or down as required,

®Rotate the coulter assembly to the LEFT so that

the drive pin located in the standard prevents the

coulter from swinging into the plow beam or bottom,

now tighten the two hex nuts When properly

adjusted, the coulter will be free to swing OUTWARD

a limited amount only, to the LEFT of the beam,

Note: tn extremely hard soil, the coulter may

actually prevent the plow from penetrating the

surface Should this situation occur +,raise, or

remove the coulter entirely

"U" Bolts-

Coulter standard"

Lop. View

,_ Piow Beam

Normal Free

Swing Range

Viewed from rear

o_ Plow

8 FIG 7

DEPTHADJUSTMENT

Referto Fig8

eTo turntheplowshareintothegroundto

openthe"first"furrow,adjustthepointdownward

untiltheplowis cutting4"to5"deep

eAfterafewfurrows,(ordesireddepthis

reached)turnthecrankCOUNTER-CLOCKWISEto

maintainthatdepth Donotallowlandsideto ride

morethan!/2" off bottomof furrowasthiswill

causeexcessivewearonbottomof shareresulting

in poorsoifpenetrationandlossoflandside

support

Depth Crank TURN CLOCKWISE

'TO INCREASE PLOW DEPTH

FIG, 8

J4URN COUNTER-CLOCKWISE

TO DECREASE PLOW DEPTH

FIG 8

TRACKING ADJUSTMENT

Refer to Fig 9

NOTE:

For most plowing conditions, the landside will

be properly adjusted (from Fig 2 assembly),

enabling the plow bottom to react like a rudder

while ground engaged But if the tip of the plow

share is too far LEFT of the beam, the plow will

tend to overcut and leave a ragged furrow wall

This condition can be readily corrected by making

the following adjustment

=_Loosen both 1/2" hex nuts securing plow bottom

to the standard and then turn the Tracking

Adjusting Bolt CLOCK-WISE two turns Retighten hex

nuts securely Repeat adjustment as necessary until

plow pulis straight behind tractor and is plowing

8" to 10" wide

LIFT ASSIST ADJUSTMENT

Standard-_4 _ _

_ndside Tracking Adjusting Bolt

FIG 9

Raise the Tractor Lift Handle to Transport in order to adjust the Spring to decrease lift effort

of the Attachment

o Loosen the Hex Jam Nut against the Spring Bushtng

¢ Turn Adjusting Bolt clockwise ("'_) until the washer is flush with Hitch Bracket, This extends

spring and reduces lift effort Retighten Jam Nut

e Operate the Hitch with the Lift Link Assembly in the Center Adjustment Hole in the Lift Arm

Assembly for most conditions, If spring adjustment does not result in acceptable lift effort, operate

the Hitch with the Turnbuckle Assembly in the Lower Adjustment Hole in the Lift Arm Assembly

Note: The Upper Adjustment Hole can be used for lighter weight attachments

CUSTOMER RESPONSIBILITY

The Moldboard should (after initial "scouring")

be kept in a smooth, polished condition Fine

sandpaper, steel wool, kerosene, naptha, etc may be

used to restore the finish on a rusty Moldboard

The Coulter Blade edge should be relatively

sharp, If sharpening is necessary, use a flat

file

0 Every 4 hours lubricate the Coulter Hub bearing

surface through the grease fitting

• For smooth operation and to prohibit the

formation of rust on the crank, keep a light

coating of oil on threads.

Note: When lubricating bearing, it is recommended

that you use multipurpose grease

TROUBLE SHOOTING

[PLOWING DIFFICULTIES AND REtVIEDIESI

PROBLEM CAUSE/CONDITION i REMEDY

® Improper Crank Adjustment. Refer to Depth Adjustment

and turn crank CLOCKWISE

t or 2 turns at a time.

SLOW GROUND ENTRY

eBadly worn Plow Share.

e Ground extremely dryand

hard due to lack of

moisture.

Replace with a new Share.

Add extra weight to tractor

or wait until soil conditions

are suitable.

Hitch downward movement

restricted by mower

height adjustmenL

Adjust for shortest cut height.

PLOW CUTTING -fOO WIDE

_. u n..nn i lul

®Improper tracking

adjustment

iiii i1,1 i

See "[racking Adjustment

i ..................... r

PLOW BOTTOM WON'T POLISH

= New or rusted bottom. Clean bottom frequently during

use until polish is obtained by:

Clean bottom with rag soaked in

turpentine, or mineral spirits.

Old brick or pumice may also be

used to polish bottom.

Or, rub with a rag soaked in

oil and dipped in sand

......... i.i ..n.i '

UNEVEN PLOWING DEPTH

eExtreme variations in soil

texture and!or moisture

•Plow rides up in harder,

dry soil, runs shallow°

See plowing tip& Soil too

wet or dry.

Reduce tractor speed in hard spots,

Check Depth Adjustment.

ePlow goes too deep

i ................. i...1111,_lnl, ...

Check Depth Adjustment,

Turn Counter-clockwise.

HOW TO ORDER

REPAIR PARTS WHEN ORDERING REPAIR pART& ALWAYS GIVE THE

FOLLOWlN6 INFORMATION:

The mode] number will be fOund o=1 the moder ptate

attached to the right hand side or the beam half

Always mention the mode_ number when requesting

service or repair parts for yOUr mold bOard p_ow

• THE PART NUMBER

•THE PART DESCRIPTION

o THE MODEL NUMBER

a THE NAME OF MERCHANDISE

All parts listed herein may be ordered from any

SEARS ROEBUCK SERVICE CENTER or most Sears retail

stores 10

If the parts you need are not stocked locany, your

order wilt be transmitted to a Sears repair parts

distribution Center for handling

Inhaltsverzeichnis

Andere Craftsman Rasen- und Gartengeräte Handbücher

Craftsman

Craftsman 610.240842 Betriebsanleitung

Craftsman

Craftsman 486.243001 Bedienungsanleitung

Craftsman

Craftsman BUSHWACKER 517.795670 Bedienungsanleitung

Craftsman

Craftsman 917.248930 Bedienungsanleitung

Craftsman

Craftsman 247.24019 Bedienungsanleitung

Craftsman

Craftsman 486.244412 Bedienungsanleitung

Craftsman

Craftsman 757 242840 Bedienungsanleitung

Craftsman

Craftsman 486.24250 Bedienungsanleitung

Craftsman

Craftsman 358.792410 Bedienungsanleitung

Craftsman

Craftsman 917.24899 Bedienungsanleitung

Craftsman

Craftsman 358.796355 Bedienungsanleitung

Craftsman

Craftsman 486.243291 Bedienungsanleitung

Craftsman

Craftsman 358.795660 Bedienungsanleitung

Craftsman

Craftsman 610.24489 Bedienungsanleitung

Craftsman

Craftsman 486.24536 Bedienungsanleitung

Craftsman

Craftsman 25241 Bedienungsanleitung

Craftsman

Craftsman 486.24560 Bedienungsanleitung

Craftsman

Craftsman 316.792520 Bedienungsanleitung

Craftsman

Craftsman 320.74900 Bedienungsanleitung

Craftsman

Craftsman C944.514320 Bedienungsanleitung

Craftsman

Craftsman 247.24019.1 Bedienungsanleitung

Craftsman

Craftsman 486.244021 Bedienungsanleitung

Craftsman

Craftsman CompuCarve 183.217540 Bedienungsanleitung

Craftsman

Craftsman ZTS 7500 Bedienungsanleitung

Beliebte Rasen- und Gartengeräte Handbücher anderer Marken

Vertex

Vertex 1/3 HP Technische Daten

GHE

GHE AeroFlo 80 Bedienungsanleitung

Millcreek

Millcreek 406 Bedienungsanleitung

Land Pride

Land Pride Post Hole Diggers HD25 Bedienungsanleitung

Yazoo/Kees

Yazoo/Kees Z9 Commercial Collection System Z9A Programmierhandbuch

Premier designs

Premier designs WindGarden 26829 Bedienungsanleitung

Snapper

Snapper 1691351 Bedienungsanleitung

Mosquito Magnet

Mosquito Magnet Patriot Bedienungsanleitung

Perfect

Perfect BG2 Bedienungsanleitung

P.Lindberg

P.Lindberg LS2 Bedienungsanleitung

Gardena

Gardena Easy 1887 Bedienungsanleitung

Makita

Makita UM104D Bedienungsanleitung

AQUA FLOW

AQUA FLOW PNRAD Bedienungsanleitung

Tru-Turf

Tru-Turf RB48-11A Golf Green Roller Benutzerhandbuch

BIOGROD

BIOGROD 730710 Bedienungsanleitung

Land Pride

Land Pride RCF2784 Bedienungsanleitung

Makita

Makita UM110D Bedienungsanleitung

BOERBOEL

BOERBOEL Standard Floating Bar Gravity Latch Bedienungsanleitung