Craftsman 33170 Bedienungsanleitung

Operator's Manual

Grass Bag Kit

for the 36-inch Wide Cut Mower

Part No. 333170

CAUTION: Before using

this product, read this

manual and follow all

Safety Rules and

Operating Instructions.

For answers to your questions

about this product, call:

1-800-659-5917

Sears Craftsman Help Line

5 a.m. - 5 p.m., Mon - Sat

Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A.

Visit our Sears website: www.sears.com/craftsman

Printed in U.S.A. FORM NO. 02005609 Rev 09_0

(10/2009)

AssemblyandOperation 2

EspaSol 8

ServiceNumbers BackCover

WARNING: Before installing this accessory, shut the engine off and allow itto cool. Disconnect the

spark plug wire from the spark plug. Refer to the mower's Operator's Manual for complete safety

instructions. Do not operate the mower without the entire grass bag in place. Turn the mower off and

disconnect the spark plug before emptying the grass bag.

CARTONCONTENTS

Before installing this accessory, remove all parts from the carton. Use caution when handling parts, some metal

parts may have sharp edges. Carton contents, including items included within the hardware pack, are shown in

Figures 1 and 2 on page 3. Part numbers are shown in parentheses and each item has been identified with a letter

code, [X], for use when following the assembly instructions. Reference to right or left side of the mower is observed

from the operating position.

TOOLSREQUIRED

Two 9/16" wrenches. Two 7/16" wrenches. One 3/8" wrench. One Flat Blade and One Phillips screwdriver.

[D]LeftLatch

(703-06695) [F]BackingPlate

(703-06692) [E]RightLatch

(703-06694) [B]BagFrame

(01003986) [C]Handles

(703-06696)

• ii

[S] Chute Baffle

(02005727)

Figure 1

[G] Cute Mounting Bracket

(703-06693) [A] Struts /

[H] Cloth Bag

(01003221)

Handle Hardware

[K] 1/4-20 x 1.00

Qty. 4

(01000944)

[I] Internal Tooth.

Washers Qty. 4

(02005631)

[L] 1/4-20 Nylock ......

nuts Qty. 4 __)

00012152)

Latch Hardware

Chute Bracket to

Backing Plate

[P] 3/8-16 X 1.00 ......._-r:

Qty. 2 -[j

(00012171)

/(f % ';

[Q] 3/8 Flat -_DP'L,, _-j/i

Washers Qty. 4

(01000723)

, x j /

'\ . J

[R] 3/8-16 Nylock

nuts Qty. 2

(00012173)

Chute Baffle

to Mower

[T] 5/16-18 X "-'----tb_

1.00 Qty. 1

(00013092)

[U] 5/16 Flat

Washers Qty. 1

(00012169)

[V] 5/16-18 Nylock

nuts Qty. 1

(00012165)

M] 10-32 x 5/8_ _

Pan Head Screws

Qty. 4 (00030906) _ j

[N] 10-32 Nylock-''l_

nuts Qty. 4

(00014608)

Figure 2

Chute Bracket

to Mower

[0] 3/8-16 X 1.25_ _-Z_

Qty. 2 (00011444) i

[R] 3/8-16 Nylock

nuts Qty. 2

(00012173)

[J] 1/4-20 x 5/8

Screws Qty. 2

(02005630) ....li....

[I] Washers _ _'&

Qty. 2

(02005631) Struts

ASSEMBLYINSTRUCTIONS

1. Remove Bag Frame [B] from Backing Plate [F].

2. Using (2) 1/4-20 x 5/8 Pan Head Screws [J] and 2

Internal Tooth Washers [I], attach two Struts [A] into

frame as shown below in Figure 3.

Struts.

Figure 3

Bolt Handle Internal Tooth Hole

Washer

Figure 5

Install Chute Mounting Bracket [G] to Backing Plate

[F] using (2) 3/8-16 x 1.00 bolts [P], (4) 3/8 Flat

Washers [Q] and (2) 3/8-16 Nylock nuts [R] as

shown below in Figure 6.

,Install the Cloth Bag [H] to Bag Frame [B]. Attach

the "J" strip of the bag to the frame using a flatblade

screwdriver to pry the strip as shown below in

Figure 4.

"J" Strip Flatblade Screwdriver

Figure 4

Attach two handles [C] to Bag Frame assembly [B]

with four 1/4-20 x 1.00 capscrews [K], four Internal

Tooth Washers [I] and four 1/4-20 Nylock nuts [L].

Insert capscrew through washer and through hole in

handle and through bag (bag must be cut to insert

bolt). Tighten nuts as shown in Figure 5.

Backing Plate Chute Mounting Bracket

Figure 6

IMPORTANT: The two bolts and two washers go J

through Chute Mounting Bracket and Backing J

Plate. Secure but do not tighten at this stage of

assemb y.

Attach Left [D] and Right Latch [E] to Backing Plate

[F] with four 10-32 x 5/8 Panhead Screws [M], and

four 10-32 Nylock nuts [N]. As shown in Figure 7 on

the next page.

PanHead

Screw

RightLatch

Nut

Figure 7

IIMPORTANT: Do not tighten nuts completely, as I

Latches must slide up and down freely.

7. Remove Chute Deflector from the mower deck by

removing (2) 3/8-16 nuts from the chute bracket

and save for future usage.

[_k, DANGER: Do not operate mower

without the grass collector installed. If the

grass collector kit is removed the chute

deflector must be installed.

8. Remove chute baffle from the mower deck. This

part will be reinstalled in the next step with the new

baffle and hardware provided. See Figure 8.

Bolt

Attach Chute Baffle [S] and chute baffle previously

removed in step 8 to the inside of the mower deck

using (1) 5/16-18 x 1.00 bolt [T], (1) 5/16 Flat

Washer, and (1) 5/16-18 Nylock nut.

See Figure 9 below.

Nut

Washer

Chute Baffle Chute Baffle

Figure 9

10. Using (2) 3/8-16 x 1.25 bolts [0] and (2) 3/8-16

Nylock nuts [R], attach backing plate [F] to the unit

as shown below in Figure 10.

Chute

Mounting

Bracket

Washer _ e_

Chute Baffl

Bolt Nut

Figure 8 Figure 10

Nut

Bolt

11.AdjustBackingPlate[F]sothatitisflushagainst

frontpartandtoppartofchuteopeningasshown

belowinFigure11andtightennutsonChute

MountingBracket[G].

BackingPlate topedgeof frontedgeof

chuteopening chuteopening

Figure11

12.AttachBagFrame[B]toBackingPlate[F]as

shownbelowinFigure12.

BagFrame BackingPlate

Figure 12

OPERATION

1. Turn the mower off and disconnect the spark plug

wire before emptying the grass bag.

2. Empty the bag when 3/4 full. To remove the grass

bag, lift up on the right and left latches to release

the top part of the grass bag. Then using the

handles, tilt the catcher assembly toward you and

lift up. This releases the lower portion of the Bag

Frame from the Backing Plate see Figure 10 on

page 6.

3. Empty bag and dispose of clippings properly.

Refer to local regulations..

4. Reattach the Bag Frame by aligning the pins in

the bottom of the Bag Frame into the holes in the

lower part of the Backing Plate. Then put the top

part into the Left and Right Latches.

DANGER: Do not operate mower I

without the grass collector installed. IfI

the grass collector kit is removed the I

chute deflector must be installed. I

Montaje y funcionamiento

Nt_mero de servicio 8

Cubierta posterior

ADVERTENClA: Antes de instalar este accesorio, apague el motor y deje que se enfr[e.

Desconecte el cable de la bujia. Lea el Manual del 'Operador de la 'cortadora de cesped para conocer

todas las instrucciones de seguridad. No opere la cortadora de cesped si la bolsa de recolecci6n no

esta.completamente en su lugar. Apague la cortadora de cesped y desconecte la bujia antes de vaciar

la bolsa de recolecci6n.

CONTENIDODELACAJA

Antes de instalar este accesorio, saque todas las piezas de la caja. ManipWelas con cuidado, algunas piezas

meta.licas tienen bordes filosos. El contenido de la caja, incluidos los articulos dentro del paquete de elementos de

ferreter[a, se muestra en las Figuras 1 y 2 en la pa.gina 3. Los nt_meros de las piezas aparecen entre parentesis y

cada elemento ha sido identificado con un c6digo de letra, [X], que debe usarse para seguir las instrucciones de

montaje. Las referencias a los lados derecho o izquierdo de la cortadora de cesped se hacen observando la

ma.quina desde la posici6n de operaci6n.

HERRAMIENTASNECESARIAS

Dos Ilaves 9/16". Dos"llaves 7/16. Una"llave 3/8. Un destornillador paleta plana y otro cabeza Phillips.

[D] Sujetador

izquierdo

(703-06695)

[F] Contraplato

(703-06692)

[E] Sujetador

derecho

(703-06694)

[B] Marco de la

bolsa

(01003986)

[C] Manijas

(703-06696)

[S] Clavija del canal

(02005727)

Figura 1

[G] Soporte de montaje del canal

(703-06693) [A] Puntales /

[H] Bolsa de tela

(01003221)

[K] 1/4-20 x 1.00.

Cantidad: 4

01000944)

Pieza metalicas a manipular Soporte de canal a

contraplato

[P] 3/8-16 x 1.00.

i _ Cantidad: 2

L -- -(00012171)

[I] Arandela

dentada interna.

Cantidad: 4

(02005631)

[L] Tuercas de .....

seguridad Nylock 1/_£_

4-20. Cantidad: 4

'00012152)

Piezas metalicas para sujetar

planas 3/8.

Cantidad: 4

(01000723)

\ J

[R] Tuercas de

segu ridad Nyl°ck 2"_,_

3/8-16. Cantidad:

(00012173)

Soporte de canal a

cortadora

[T] 5/16-18 x

1.00. Cantidad: 1"""1_

/ooo13o92t

[U] Arandelas

planas 5/16.

Cantidad: 1

(00012169)

[V] Tuercas de

seguridad Nylock 5/

16-18. Cantidad: 1

(00012165)

M] Tornillo de

cabeza completa

10-32 x 5/8.

Cantidad: 4

(00030906)

[N] Tuercas de

seguridad Nylock

10-32. Cantidad: 4

00014608)

Figura 2

Soporte de canal a

cortadora

[O] 3/8-16 x 1.25.

Cantidad: 2 J-_-i__

(00011444) _ ii

JR]Tuercas de

seguridad Nylock

3 8_ 6.oaot,dad:

(00012173)

[J] Tornillos 1/4-

20 x 5/8.

Cantidad: 2

(02005630)

[I] Arandelas.

Cantidad: 2

(02005631) Puntales

INSTRUCCIONESDEMONTAJE

1. Extraiga el marco de la bolsa [B] del contraplato [F].

2. Usando (2) tornillos de cabeza completa 1/4-20 x 5/8 [J] y

(2) arandelas dentadas internas [I], fije dos puntales [A] al

marco, segQn se muestra a continuaci6n en la figura 3.

Figura 3

Puntales

Arandela

Perno Manija dentada interna Orificio

Figura 5

Instale el soporte de montaje del canal [G] en el

contraplato [F] usando (2) pernos 3/8-16 x 1.00 [P], (49

arandelas planas 3/8 [Q] y (2) tuercas de seguridad

Nylock 3/8-16 [R] segt]n se muestra en la Figura 6.

3, Instale la bolsa de tela [H] en el marco de la bolsa [B]. Fije

la franja de la bolsa "J" al marco con un destornillador de

paleta plana a fin de hacer palanca en la franja como se

muestra a continuaci6n en la Figura 4.

"J" Franja Destornillador de paleta plana

Figura 4

Fije dos manijas [C] al montaje del marco de la bolsa [B]

con cuatro tornillos de cabeza 1/4-20 x 1.00 [K], cuatro

arandelas internas dentadas [I] y cuatro tuercas de

seguridad Nylock 1/4-20 [L]. Inserte los tornillos en las

arandelas a trav_s de la manija y la bolsa (la bolsa debe

estar cortada para insertar el perno). Ajuste las tuercas

segQn se muestra en la Figura 5.

Contraplato Soporte d tje del

canal

Figura 6

IMPORTANTE: Los dos pernos y las dos arandelas

van a traves del soporte de montaje del canal y

contraplato. Asegurelos, pero no los ajuste en este

paso del montaje.

Fije el sujetador izquierdo [D] y derecho [E] al contraplato

[F] con cuatro tornillos de cabeza completa 10-32 x 5/8

[M] y cuatro tuercas de seguridad Nylock 10-32 [N]. Como

se muestra en la Figura 7 en la siguiente pagina.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Craftsman Rasenmäherzubehör Handbücher

Craftsman

Craftsman 917.249781 Bedienungsanleitung

Craftsman

Craftsman 917.249890 Bedienungsanleitung

Craftsman

Craftsman 917.249050 Bedienungsanleitung

Craftsman

Craftsman 48"MOWER 917.24985 Bedienungsanleitung

Craftsman

Craftsman 61102 Bedienungsanleitung

Craftsman

Craftsman 486.248471 Bedienungsanleitung

Craftsman

Craftsman 102.249020 Bedienungsanleitung

Craftsman

Craftsman 247.240192 Bedienungsanleitung

Craftsman

Craftsman 917.249170 Bedienungsanleitung

Craftsman

Craftsman 917.249900 Bedienungsanleitung

Craftsman

Craftsman 486.248472 Bedienungsanleitung

Craftsman

Craftsman 917.249391 Bedienungsanleitung

Craftsman

Craftsman 486.24240 Bedienungsanleitung

Craftsman

Craftsman 917.248971 Bedienungsanleitung

Craftsman

Craftsman 486.242101 Bedienungsanleitung

Craftsman

Craftsman 917.248962 Bedienungsanleitung

Craftsman

Craftsman 24919 Bedienungsanleitung

Craftsman

Craftsman Smart Lawn Connect Kit Bedienungsanleitung

Craftsman

Craftsman 33731 Bedienungsanleitung

Craftsman

Craftsman 132.24607 Bedienungsanleitung

Craftsman

Craftsman 917.249660 Bedienungsanleitung

Craftsman

Craftsman 917.248960 Bedienungsanleitung

Craftsman

Craftsman 486.243152 Bedienungsanleitung

Craftsman

Craftsman 917.249870 Bedienungsanleitung

Beliebte Rasenmäherzubehör Handbücher anderer Marken

Ariens

Ariens 891008 Bedienungsanleitung

Rover

Rover 108 - 109 Bedienungsanleitung

Toro

Toro 112-5803 Bedienungsanleitung

Snapper

Snapper 1690047 Bedienungsanleitung

Scag Power Equipment

Scag Power Equipment GC-F4 Bedienungsanleitung

RHINO

RHINO 800 Bedienungsanleitung

Exmark

Exmark Quest 126-7506 Bedienungsanleitung

Snapper

Snapper 1685167 Bedienungsanleitung

Cub Cadet

Cub Cadet 19B70029100 Bedienungsanleitung

Stihl

Stihl AMK 043.1 Bedienungsanleitung

MTD

MTD 753-0873 Handbuch

Toro

Toro 30810 Bedienungsanleitung

Bush Hog

Bush Hog RG60 Bedienungsanleitung

Land Pride

Land Pride RCF2760 Bedienungsanleitung

Simplicity

Simplicity 211 Bedienungsanleitung

Toro

Toro Z Master 116-0231 Bedienungsanleitung

Exmark

Exmark ULTRAVAC QUICK DUMP SYSTEM Bedienungsanleitung

Excel

Excel Two Bag Catcher Bedienungsanleitung