Craftsman 917.372260 Bedienungsanleitung

¢40DEL NO.

917.372260

4.0 RESERVE POWER

22" POWER-PROPELLED

LA WN M 0 WER

THIS MOWER COMPLIES WITH CPSC REGULATIONS EFFECT|VE JUNE 30, 1982, TO START THE ENGLNE tT tS NECESSARY

TO DEPRESS THE CONTROL BAR WHEN STANDING BEHIND THE MOWER, BEFORE PULLING ON THE STARTER ROPE,

FOR FURTHER STARTING DETAILS SEE PAGE 8 OF THIS MANUAL,

SEARS, ROEBUCK AND CO., CHICAGO, IL 60684 U.S.A.

_ART NO. 87867 REV. 2 4!5/88

CRAFTSMAN quality LAWN CARE equipment

TWOYEARLIMITEDWARRANTYONCRAftSMANPOWERMOWEn

For two years from the date of purchase, when this Craftsman power mower is maintained, lubricated and

tuned-up according to the instructionsin the owner's manual, Sears will repair, free of charge, any defect

in material and workmanship.

If this Craftsman power mower is used for commercial or rental purposes, this warranty applies for only

90 days from the date of purchase.

This warranty does not cover:

Expendable items which become worn during normal use, such as rotary mower blades, blade

adapters, belts, air cleaners and spark plug.

Repairs necessary because of operator abuse or negligence, including bent crankshafts and the failure

to maintain the equipment acc0rdingt 9the instructionscontained in the owner's manual.

WARRANTYSER ,C IAVA, BLERETURN,NGT.ECRAFTSM NPOWERMOWERTOT,E

NEAREST SERVICE CENTER/DEPARTMENT IN THE UNITED STATES.

Thiswarranty gives you specific legal rights, and you may also have other rights which may vary from state

to state.

SEARS, ROEBUCK and CO. Department 698/731A Sears Tower, Chicago, III. 60684 Jl_

.... I'11r1'111111I[ Ff,rrm_ffT

MAINTENANCE AGREEMENT

A SEARS MAINTENANCE AGREEMENT IS AVAILABLE ON THIS PRODUCT. CONTACT YOUR

NEAREST SEARS STORE FOR DETAILS.

CUSTOMERS RESPONSIBILITIES

Read and observe the rules for safe use. Always use care when using your lawn mower. Keep away from

moving parts.

DO NOT work on your lawn mower with engine running. Always keep your mower clean.

Follow a regular schedule in maintaining, caring for and using your lawn mower. Awell cared for mower

will run and last longer.

Fallow the instructionsunder "Maintenance" and "Storage" sectionsof this Owner's Manual.

Blade, blade flange, ai_ _J_n_r/ai_ fiii_r, _park plug are expendable parts which are your responsibility.

TABLE OF CONTENTS

WARRANTY ........................................................ 2

KNOW YOUR CRAFTSMAN MOWER ........................................ 3

RULES FOR SAFE USE ................................................... 4

HELP YOUR LAWN MOWER LAST LONGER .................................... 5

HOW TO SET-UP YOUR MOWER ........................................... 6

BEFORE STARTING ENGINE ............................................... 8

HOW TO USE YOUR MOWER ............................................. 9

MAINTENANCE ....................................................... 11

STORAGE ........................................................... 15

REPAIR PARTS ....................................................... 17

ENGINE REPAIR PARTS ................................................ 24

TROUBLE SHOOTING ................... ................................ 16

KNOW YOUR CRAFTSMAN®MOWER

ZONE/ENGINE

CONTROL

HANDLE KN(

GRASS CATCHER

HANDLE BRACKET

ENGINE CONTROL KNC

PRIMER

AIR FILTER

FIG. 1

CABLE CLIP

31NE OIL CAP WiTH DIPSTICK

GASOLINE FILLER CAP

WHEEL ADJUSTER

(ON EACH WHEELI

DRIVE COVER

HOUSING

MEETS CPSC BLADE SAFETY REQUIREMENTS

SPECIFICATIONS TOOLS REQUIRED

Oil: Use SAE 30W motor oil. SAE 10W30

motor oil con also be used.

Gasoline: Use unleaded automotive

gasoffne. Regular automotive gasoline can

also be used. DO NOT use premium

gasoline.

FOR CATCHER ASSEMBLY

7/16" wrench or

adjustable wrench.

Medium phillips screwdriver.

FOR BLADE REMOVAL

Standard 15116" box or open

end wrench

_ears Rotary Walk-Behind Power Mowers conform to the safety standards of the American National Standards Institute, Outdoor

Sower Equipment lhstitute, and U.S. Consumer Product Safety Commission, as applicable.

RULES FOR SAFE USE

CAUTION: ALWAYS DISCONNECT SPARK PLUG WiRE AND PLACE WIRE WHERE A

IT CANNOT CONTACT SPARK PLUG TO PREVENT ACCIDENTAL STARTING

WHEN SETTING-UP, TRANSPORTING, ADJUSTING OR MAKING REPAIRS TO

YOUR MOWER.

IMPORTANT

FEDERAL REGULATIONS REQUIRE THE ENGINE CONTROL INSTALLED ON THIS MOWER IN ORDER TO

MINIMIZE THE RISK OF BLADE CONTACT INJURY. DO NOT UNDER ANY CIRCUMSTANCE ATTEMPT TO

DEFEAT THE FUNCTION OF THE OPERATOR CONTROL.

1. Please read your owner's manual.

Only allow persons who know the

safety rules to use your mower.

2. DO NOT tie the control bar to the han-

dle. Control must be free to permit

brake engagement when handles and

control are released.

3. DO NOT altow children to use your

mower.

4. Check your mower over before each

time you mow. Tighten any loose

bolts, nuts, etc.

5. Remove all sticks, stones, wires, cans,

boards, etc. from area to be mowed.

These objects can be thrown by the

blade.

6. DO NOT allow children, bystanders,

or pets in the mowing area.

7. BE CAREFUL-WHEN THE ENGINE

IS RUNNING THE BLADE IS

TURNING.

8. Always shut off engine before trying

to adjust wheel heights.

9. When engine is running, DO NOT put

hands or feet under mower or in the

discharge chute, nor make any

adjustments.

10. Stay clear of discharge opening at all

times.

11. Check gasoline before each use. Do

not fill gas tank when engine is run-

ning, when indoors or when engine is

hot. Allow engine to cool for several

minutes before filling gas tank. Clean

off any spilled gasoline before starting

engine.

12. Mow onl_ in good light.

! 3. Wear on,y solid shoes when mowing.

DO NOT operate mower when

barefoot, or wearing open sandals.

14. Disengage drive control on power

pro.pelled mowers before starting

engine.

I5. DO NOT use a damaged mower.

Always have damage repaired

before mowing.

16. Always stop engine when not cutting

grass or when crossing gravel drive,

sidewalk, or roadway.

17. Never pull mower towards you,

always follow mower to cut grass.

18. Never use your mower without pro-

per guards or deflectors in place.

19. Always mow across a slope or inclin-

ed area. DO NOT mow up or down

a slope or inclined area.

20. DO NOT mow in wet grass. DO NOT

run with the mower.

21. DO NOT run your mower indoors.

Exhaust gases are deadly poison.

22. DRAIN THE GASOLINE tank before

transporting your mower inside your

car or other vehicle.

23. DO NOT run your mower if it vibrates

too much. Stop engine and make

repairs. Vibration isan indication of

damage.

24. DO NOT change the engine gover-

nor settings to over-speed the

engine--damage or injury can result.

25. If a grass catcher is used on your

mower, check the catcher often for

damage or deterioration. Through

normal use it will wear. Use only

recommended replacement catcher.

Always stop engine to remove

catcher.

26. DO NOT store your mower or

gasoline where fumes may reach an

open flame and cause a fire.

27. Always wear safety glasses or eye

shields before starting your lawn

mower and while mowing.

The operation of any lawn mower can result in foreign obiects thrown into the

eyes,, which can result in severe eye damage, Always wear safety glasses or eye

shields before starting your lawn mower and while mowing° We recommend Wide

Vision Safety Mask for over the spectacles or standard safety glasses, available

at Sears Retail or Catalog Stores,

ACCESSORIESTO HELPYOU GETTHEMOST FROMYOUR MOWER

_OWER COVER: Sears Tyvek_cover, stock number 7) 33316, protects mower from weather when stored outdoors.

_vailable through Sears catalog.

_AS CAN: A new gas can keeps rust and dirt out of fuel system for longer engine life and improved performance. Craft-

_an gas cans have built in filters to keep impurities out of your engine and are available in Permanex ®polyethylene

,ith lifetime warranty and strong terneplate steel.

:LIPP1NG DEFLECTOR: Converts rear bagging mowers to side discharge to disperse safely and evenly, stocknumber

'1 33303 avai able in most retail stores, through catalog, Sears Central Service and parts desks. N-TE

GH WHEEL K T A pair of 12-inch rear wheels improves handling on soft, spongy lawns and uneven terrain, u :

:the Z! 3372 t High Wheel Kit ispurchased as an accessory, the cutting height range wilf be reduced to five (5) different

ositions; from 1 1/2" to 3 1/2". Available through catalog and Sears Central Service and Parts desks.

HESE ACCESSORIES WERE AVAILABLE AT MOST SEARS STORES AND THROUGH THE CATALOG AT THE TIME

HIS MANUAL WAS PRINTED.

IMPORTANTTIPSTO HELPYOUR LAWN MOWERSTARTFASTER,RUN AND PERFORMBETTER

1. USE UNLEADED GASOLINE: It burns cleaner and leaves less residue in the engine. Regular gasoline can also be

used. DO NOT use PREMIUM GASOLINE.

2. DRAIN OR RUN-OUT ALL GASOLINE FROM TANK AT THE END OF THE SEASON: DO NOT leave gasoline

in your mower when stored for long periods. It will "GUM" your engine. Run engine until the gasoline runs out.

3. START EACH MOWING SEASON WITH FRESH GASOLINE: DO NOT keep gasoline in your can. If your gasoline

can is starting to rust, replace can.

4. CHANGE YOUR SPARK PLUG EVERY SPRING: An old corroded spark plug prevents fast starting and smooth

running engine.

5. REPLACE YOUR AIR CLEANER OR FILTER OFTEN: Dirt, along with heat can harm your engine, the cleaner or

filter will clog up, preventing clean air from reaching your engine. See "Air Cleaner/Filter" section of this manual

for replacing air cleaner or filter_

6, USE SAE 30W OIL: DO NOT use SAE 10W40 oil.

7. CHANGE OIL AS RECOMMENDED: IMPORTANT - change oil after the first two (2) hours of use, then every 25

hours of use.

8. REPLACE THE BLADE WHEN NEEDED: You can sharpen the blade, but we do not recommend it. Erosion from

hitting foreign objects can damage the blade, Replace blade with one specifically designed for your mower.

9. AT THE END OF THE SEASON, CLEAN YOUR MOWER: IMPORTANT - first disconnect the spark plug wire. If

possible, store your mower in a well ventilated area and protected from moisture.

O. FOLLOW THE MAINTENANCE SUGGESTIONS IN YOUR OWNERS MANUAL: Read your manual and keep

it in a convenient piace_f-6i'_easy reference.

Your lawn mower has been completely assembled at the factory, except for the grass catcher. To set-up and attach gross

_tc_r, follow the steps under "GRASS CATCHER"

The foflowing parts are included not assembled:

1Grass Catcher Top Assembly

I Grass Catcher Bottom

1 Hardware Package

HOWTOSET-UPYOURMOWER

TOUNFOLDHANDLE

t. Raise handles until the lower handle isin upright posh

tion (See Fig. 2).

NOTE: The lower handle automatically locks into the

upright storage position when raisedfrom shipping

position.

2. Raise the upper handle intoposition on the lower han-

dle and tighten the two (2) handle knobs.

3. The handle can be mounted in high or low position

to suit the comfort of the user. The handles are ship-

ped mounted in the high position.

4. If the handle feels too high for you:

a. Remove the (2) screws, (2) bushings, (I) bolt and

Iocknut holding the trimplate and rope guide to lower

handle. Keep for re-assembly (See Fig. 4).

b. Remove the handle knobs and bolts from upper

and lower handle.

c. Remove the springs from mounting pins {bee Fig.

3).

d. Remove/ocknuts and bolts from handle brackets

and remove handle levers (Se Fig. 3).

e. Turn handle over, position handle levers inplace

(See Fig. 4).

.Reinstall bolts and/ocknuts (See Fig. 3).

• Put springs back on mounting pins (See Fig. 3).

. Put upper handle on lower handle using handle

bolts and knobs previously removed.

i. Puttrim plate and rope guide back on lower han-

dle, removed in (a) above. Tightenthe (2) screws,

(2) bushiness,(t) bolt, tighten (2) screws and (I)

Iocknut (See Fig. 4).

I. Snap cable c;o over cable and lower handle [See

Fig.I).

5. Press the handle levers and the handle wilt

automatically lock in_omowing position.

6. To fold handle for storage, press the handle levers

and move handle forward (Fig. 3).

CAUTION: WHEN FOLDING HANDLE FOR

TRANSPORTING OR STORAGE, BESURE TO FOLD

HANDLE AS SHOWN /N FIG. 5. /F YOU FOLD

HANDLE THE WRONG WAY, YOU MAY BEND

THE CONTROL CABLES.

TOADJUSTHEIGHTOFCUT

NOTE: The wheels are set in alow cut position for ship-

ment, and shouldbe adjusted for the cutting heightdesired

before use. NOTICE: Lowering wheels raises the height

of cut.

UPRIGHTHANDLE ._,'- ",,

STORAGEPOSITION k_

AND REMOVING lt

MOWING l

POSITION _,;

LOCKNUT

HANDLE

BRACKET

FIG. 3

HOWTOSET-UPYOURMOWER(¢ONT'D)

TOADJUSTHEIGHTOFCUT(CONT'D}

CAUTION: DO NOT change the height of cut with the

engine running,

I. The wheel adiusters give you five (5) different cutting

positions. Medium cut is the best for most lawns.

2, High cut is approximately 3 3/8 "_,medium cut is ap-

xIm _t •

pro "ately 25/8 and low cut zsapproximately 1

I/8" There are two (2) otherpositlons. Pick the posi.

tion which suits you for best cutting (See Fig. 6).

3. The wheel adjusters on your lawn mower can be easi.

ly adjusted as shown in Fig. 7. To change the height

of cut, squeeze adjuster lever toward the wheel, mov-

ing up or down to selected height. Be sure all wheels

are in the same setting (See Fig. 6).

4. When cutting in heavy or moist grass, the rear of the

lawn mower may be raised one setting higher (by

lowering the wheels one setting) to allow better

discharge of the grass.

This will also make the unit push or propel easier

because it will reduce the drag of the rear of the

mower on the grass. This will not harm the cutting

performance.

LOW

MED

iIit11I \

_ j_s

• WHEEL ADJUSTER LEVER

SHOWN WITH WHEEL REMOVED

FIG. 6

REARDEFLEaOR

The rear deflector, attached between the rear wheels of

your lawn mower, was assembled at the factory and re-

quires no assembly.

T0 ASSEMBLEGRASSCATCHER

NOTE: The grass catcher for your mower is supplied

unassembled. To assemble your grass catcher follow steps

below.

SCREW ACTUAL SIZE

1/4-20 x 3/4"" SCREW

1. Position top half of catcher on the bottom haft (See

Fig.8).

2. Insert I/4-20 x 3/4 truss head screw through right

front hole of catcher; install 1/4 nut on screw and

leave loose (See Fig. 8).

3. Insert a 1/4-20 x 3/4 screw through left front hole

of catcher; install !/4 nut on screw and leave loose.

4. Tighten screws installed in steps2 &3. Use a medium

phillips screwdriver to tighten the screws while

holding] the Iocknuts with adjustable or 7/16"

wrench.

5. Install six more 1/4-20 x 3/4 screws, proceeding

around the catcher; leave Iocknuts loose.

6. Use a medium phl_fips s_ewdriver to tighten the re-

maining screws while holding the Iocknuts with ad-

justable or 7/16'" wrench.

NOTE: Check all screws and nuts to be sure they are tight.

FIG, 7

CATCHER TOP

1/4-20 x 3/4"

TRUSS HEAD

SCREW

CATCHER BOTTOM

START HERE

1 4 20 KEPS NUTS

FIG. 8

HOWTOSET-UPYOURMOWER(¢ONT'I))

TOATTACFIGRASSCATCHER

1. Lift rear door.

2. Holding the catcher by the handle, place catcher

frame onto hinge bracket (Fig. 9).

3. Release rear door.

4. When grass catcher is removed from the mower, the

rear door closes for safety.

NOTE: YOUR REAR BAGGER MOWER IS NOT A

MULCHING MOWER. DO NOT OPERATE YOUR

MOWER WITHOUT AN APPROVED GRASS CA T.

CHER OR OPTIONAL CLIPPING DEFLECTOR IN

PLACE.

NEVER ATTEMPT TO OPERATE THE MOWER WITH

THE DOOR REMOVED OR PROPPED OPEN.

TOEMPTYGRASSCATCH[R

1. Lift grass catcher, by grasping the handle on top of

grass catcher and on the rear of catcher (See Fig. 10).

2. To empty the grass clippings, shake the catcher, with

the open end aver or inta suitable container for

disposal (See Fig. t0).

BEFORESTARTINGENGINE

i. Remove engine oil cap with dipstick and fill to the

"FULL" line on the dipstick, using about 1 pint of

Sears 30W all or equivalent. SAE 30W oil can also

be used(See Fig. 11). DO NOT useSAE lOW40 oil.

The total oil capacity of your engine is 21 oz. Fill only

to the "FULL'" line on the dipstick. DO NO Tover fill. The

first fill on a new engine useabout Ipint. Check oil Jevel

and add as required to bring to proper level.

2. Pour oil slowly, DO NOT over fill.

NOTE: On anew engine some oil may be left in the

engine, as each engine is run for operational checks

before shipping.

3. AFTER THE FIRST TWO (2) HOURS OF MOWING

CHANGE THE OIL. See "To Change Oil" section

under maintenance.

Use only all with automotive classifications SF, SE, SD

or SC markings on oil container.

_c:ll_e g:Experience indicates that alcohol blended fuels

asohoi or using ethanol or methanol) can attract

moisture whichleads to separation and formation of acids

duri'ng storage. Addi'c gas can damage the fuel system

of an engine while in storage.

To ovoid engine problems, the fuel systemshould be emp-

tied before storage for 30 days or longer. Dram the gas

tank, start the engine and let # run until the fuel linesand

carburetor are empty. Use fre.shfuel next season. See

Storage Insh_uctions for additional information.

Never use engine or carburetor cleaner products in the

fuel tank or permanent damage may occur.

JNGE BRACKET

DOOR OPEN

FiG 9

FIG. 10

GASOLINE FILLER CAP

OIL FILLERPLUG

FIG. 11

4. Fill thegasoline tank with about one (I) quart offresh,

clean unleaded automotive gasoline. Regular leaded

gasohne can also be used (See Fig. 11).

DO NOT use old or stale gasoline which has been kept

from one season to another; starting problems can result.

BE SURE YOUR GASOLINE CAN IS CLEAN AND J

FREE OF RUST AND DIRT.

REPLACE YOUR CAN IF IT HAS STARTED TO RUST.

HOWTOUSEYOURMOWER

iMPORTANT

ENGINE¢OHTROL

CAUTION: THE BLADE TURNS WHEN THE ENGINE

15 RUNNING.

YOUR MOWER tS EQUIPPED WITH AN OPERA TOR

ZONE ENGINE CONTROL WHICH REQUIRES THE

OPERATOR TO BE POSITIONED BEHIND THE

MOWER HANDLE TO START AND OPERATE THE

MOWER.

THE CONTROL BAR MUST BE DEPRESSED TO THE

HANDLE TO 5TART AND RUN THE ENGINE, RELEAS-

ING THE CONTROL BAR WILL STOP THE ENGINE.

AN INTERNAL ENGINE BRAKE ASSISTS THE BLADE

IN STOPPING QUICKL Y.

WHEN THE OPERATOR LEAVES THE NORMAL

MOWING POSITION TO REMOVE THE GRASS CAT-

CHER, CHANGE THE CUTTING HEIGHT, PICK UP

5TICK5 OR OTHER OBJECT5 IN THE MOWING PATH,

THE ENGINE WILL AUTOMATICALLY STOP WHEN

THE CONTROL BAR IS RELEASED.

CAUTION; FEDERAL REGULATIONS REQUIRE THE

ENGINE CONTROL INSTALLED ON THIS MOWER IN

ORDER TO MINIMIZE THE RISK OF BLADE CONTACT

INJUR Y. DO NOT UNDER ANY CIRCUM5TANCE A T-

TEMPT TO DEFEAT THE FUNCTION OF THE

OPERATOR CONTROL.

ENGINECONTROL

The engine speed is controlled by a lever (red knob)

located on right side of engine, It has '_HIGH'" and

"LOW"positions. "'HIGH" position isfor starting engine,

heavy cutting and better grass bagging. "LOW" posi-

tion is for light cutting, trimming and fuel economy (See

Fig. 12).

TO STARTENGINE

THE CONTROL BAR MU5T BE DEPRE55ED TO THE

HANDLE TO 5TART AND RUN THE ENGINE.

NOTE: The carburetor has a fixed fuel mixture and has

a primer to assist starting.

I. Check oil level; check gasoline tank for _]asoline; and

make sure spark plug wire is attachea,

2. Push lever forward to "HIGH"position (See Fig. 12).

3. When starting a cold engine, push the primer five (5)

times before pulling starter rope. Use firm pushes

when pushing primer, wait several seconds between

each push (See Fig. 12).

4. Repeat step 3 above as required.

NO TE: In cooler weather the need to repeat priming pro-

cedures may be necessary, when weather is warmer over

priming may result in flooding.

If you do flood engine wait a few minutes before

repeating priming procedures.

It is not necessary to use t_rner to start warm engine,

5. Position yourself as shown in Fig. 15.

6. Pull on starter handle quickly.

7. DO NOT allow starter rope to snap back.

8, To stop the engine, release the control bar (See Fig.

14).

FIG. 12

CONTROL BAR

;INE

CONTROL

TO ENGAGE

DRIVE CONTROL.

FIG, 13

CONTROL

RELEASED

ENGINE STOP

FIG. 14

FIG, 15

CONTROL

OR_VE CONTRO

DISENGAGED

CONTROL

DEPRESSED jSTART. RUN

HOWTOUSEYOURMOWER((ONT'D)

IF ENGINEDOESNOTSTART

1. Check blade -remove spark plug wire when checking

blade. If blade is loose, see "BLADE AND BLADE

FLANGE CARE" of manual for instructionson tighten-

ing blade.

2. Check air filter - replace ff dogged. ,See "Air Filter"

section.

3. Check spark plug . if dirty, clean or replace.

4. Observe that lower end of the engine control cable

is actuating the lever mounted on the engine.

5. Engine may be flooded -wait afew minutes and

repeat starting procedure.

NOTE: If then your engine will not start, contact your

nearest Sears Service Department for help.

ZONE/ENGINECONTROL

Your mower is equipped with a zone/engine control at-

tached and requires no adjustments (See Fig. 13).

DRIVE CONTROL

The power-propelling forward motion is controlled by

pulling the control bar down to handle and pushing the

drive control lever forward until it clicks,then release the

lever (See Fig. 13).

Forward motion wil! stop when the controlbar isreleased.

To stop forward motion without stopping the engine,

release the control bar slightly untilthe drive control

disengages. Depress control bar to handle to continue

mowing without self-propelling.

To turn corners, you may prefer to keep the drive control

engaged, and push down on the handle, lifting the front

wheels off the ground and turning mower.

POWER-PROPELLEDDRIVE

1. Yourpower-propelled drive isaccomplishedby a belt

drive from the engine crankshaft to a Worm gear case.

2. The drive belt is sprlng.loaded at the gear case to

maintain proper belt tension. Keep the area around

the gear case clear of trash by removing drive cover

and deanlng (See Fig. 16 and 17).

3. The gear case is lubricated with multi.purpose

automotive grease. DO NOT USE ANY OTHER type

grease or oil in the gear case. See "GEAR CASE'"

under "Maintenance".

4. Check your mower, each time you mow, to be sure

that the front wheels turn freely. If wheels DO NOT

turnfreely, remove any trash which may have gotten

into the wheel, pinion, or bearing areas.

5. If at any time, the drive belt isreplaced, useonly fac-

tory specified belt to get longer life and maximum

performance.

MOWINGTIPS

I. Under certain conditions it may be necessary to raise

the height of cut to keep from overloading the engine

and leaving dumps of grass clippings.

FIG. 16

FIG. 17

BLOCK OF WOOD

FIG. 18

CRANKSHAFT &

BLADE FLANGE

DETAIL

_RANKSHAFT

SLOT

LADE NUT

BLADE WASHERS

TAB _ADE

BLADE FLANGE

FIG. 19

Andere Craftsman Rasenmäher Handbücher

Craftsman

Craftsman 917.387850 Bedienungsanleitung

Craftsman

Craftsman 917.378412 Bedienungsanleitung

Craftsman

Craftsman 247.37638 Bedienungsanleitung

Craftsman

Craftsman 917.388730 Bedienungsanleitung

Craftsman

Craftsman 917.27664 Bedienungsanleitung

Craftsman

Craftsman No. 172.796570 Bedienungsanleitung

Craftsman

Craftsman 917.271851 Bedienungsanleitung

Craftsman

Craftsman EZ3 917.270813 Bedienungsanleitung

Craftsman

Craftsman 917.271052 Bedienungsanleitung

Craftsman

Craftsman R100 Series Bedienungsanleitung

Craftsman

Craftsman 917.27690 Bedienungsanleitung

Craftsman

Craftsman 38105 Bedienungsanleitung

Craftsman

Craftsman 917.272431 Bedienungsanleitung

Craftsman

Craftsman 247.378970 Bedienungsanleitung

Craftsman

Craftsman 944.600191 Bedienungsanleitung

Craftsman

Craftsman 917.272265 Bedienungsanleitung

Craftsman

Craftsman 917.28008 Bedienungsanleitung

Craftsman

Craftsman 917.275754 Bedienungsanleitung

Craftsman

Craftsman 917.389382 Bedienungsanleitung

Craftsman

Craftsman EZ3 917.377630 Bedienungsanleitung

Craftsman

Craftsman 917.271060 Bedienungsanleitung

Craftsman

Craftsman 917.255441 Bedienungsanleitung

Craftsman

Craftsman 917.276101 Bedienungsanleitung

Craftsman

Craftsman 247.375900 Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Toro

Toro Groundsmaster 3505-D Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

AIRFORCE

AIRFORCE F-15 Gen 3 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Toro

Toro 74806 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung