Craftsman 82140 Bedienungsanleitung

Owner's Manual

JCRAFTSMAN I

Digital MultiMeter

Model No. 82140

and

Voltage Detector

Model No. 82174

CAUTION: Read, understand and

follow Safety Rules and Operating

Instructions in this manual before

using this product.

• Safety

• Operation

• Maintenance

• EspaSol

©Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

www.craftsman.com 070606

II:_ :] ! :[o] |o[o] _/ / :1_/_

Warranty

Safety Instructions

Safety Symbols

Control and Jacks

Symbols and Annunciators

Specifications

Battery Installation

Operating Instructions

DC Voltage Measurements

AC Voltage Measurements

DC Current Measurements

Resistance Measurements

Continuity Check

Diode Test

Battery Test

Maintenance

Replacing Batteries

Replacing Fuses

Troubleshooting

Service and Parts

Model 82174 instructions

Page

ONEYEARFULLWARRANTYONCRAFTSMANMANUALRANGING

MULTIMETER

IfthisCRAFTSMANManualRangingMultiMeterfailstogivecomplete

satisfactionwithinoneyearfromthedateofpurchase,RETURNITTO

THENEARESTSEARSSTOREOROTHERCRAFTSMANOUTLETIN

THEUNITEDSTATES,andSearswillreplaceit,freeofcharge.

IfthisCRAFTSMANManualRangingMultiMeterisusedforcommercial

orrentalpurposes,thiswarrantyappliesfor90daysfromthedateof

purchase.

Thiswarrantygivesyouspecificlegalrights,andyoumayalsohave

otherrightswhichvaryfromstatetostate

Sears,RoebuckandCo.,Dept.817WA,HoffmanEstates,IL60179

For Customer Assistance Call 9am-5 PM (EST)

Monday through Friday 1-888-326-1006

WARNING: USE EXTREME CAUTION IN THE USE OF THIS DEVICE.

Improper use of this device can result in injury or death. Follow all

safeguards suggested in this manual. In addition to the normal safety

precautions used in working with electrical circuits. DO NOT service this

device if you are not qualified to do so.

Thismeterhasbeendesignedforsafeuse,butmustbeoperatedwith

caution.Theruleslistedbelowmustbecarefullyfollowedforsafeoperation.

1. NEVERapplyvoltageorcurrenttothemeterthatexceedsthe

specifiedmaximum: InputLimits

Function MaximumInput

VAC 600VDC/AC

VDCorVAC 600VDC/AC,200Vrmson200mVrange

mADC 200mA250Vfastactingfuse

ADC 10A250Vfastactingfuse(30secondsmax

every15 minutes)

Resistance, Continuity 250Vrms for 15sec max

2. USE EXTREME CAUTION when working with high voltages.

3. DO NOT measure voltage if the voltage on the "COM" input jack

exceeds 500V above earth ground.

4. NEVER connect the meter leads across a voltage source while the

function switch is in the current, resistance, or diode mode. Doing so

can damage the meter.

5. ALWAYS discharge filter capacitors in power supplies and disconnect

the power when making resistance or diode tests.

6. ALWAYS turn off the power and disconnect the test leads before

opening the doors to replace the fuse or batteries.

7. NEVER operate the meter unless the back cover and the battery and

fuse doors are in place and fastened securely.

.-"9'_"__I:IIIk'dl,,"]k'd_"+I:[o]n_

IwARN'NGI

I CAUTIONI

[-MAX

500V

This symbol adjacent to another symbol, terminal or

operating device indicates that the operator must refer

to an explanation in the Operating Instructions to avoid

personal injury or damage to the meter.

This WARNING symbol indicates a potentially

hazardous situation, which if not avoided, could result

in death or serious injury.

This CAUTION symbol indicates a potentially

hazardous situation, which if not avoided, may result

damage to the product.

This symbol advises the user that the terminal(s) so

marked must not be connected to a circuit point at

which the voltage with respect to earth ground

exceeds (in this case) 500 VAC or VDC.

This symbol adjacent to one or more terminals

identifies them as being associated with ranges that

may, in normal use, be subjected to particularly

hazardous voltages. For maximum safety, the meter

and its test leads should not be handled when these

terminals are energized.

This symbol indicates that a device is protected

throughout by double insulation or reinforced insulation.

o_o]_IIII_,To]L',]F:I _Ie]LnlT:T_[_:

1. LCD Display

2. Function switch

3. COM jack

4. 10A jack

5. Positive jack

Note: Tilt stand, fuse and battery

compartment are on rear of unit.

H=O __ k, | __ k, k, k, __ O_

•))) Continuity

"_ Diode test

micro (amps)

m milli ( volts, amps)

k kilo (ohms)

£_ ohms

VDC volts direct current

VAC volts alternating current

ADC amps direct current

BAT Battery test

Function

DCVoltage

(VDC)

ACVoltage

(VAC)

DCCurrent

(ADC)

Resistance

BatteryTest

Range

200mV

2000mV

20V

200V

600V

200V

600V

2000#A

20mA

200mA

10A

200£2

2000£2

20k£!

200k£!

2000k£!

1.5V

Resolution

0.1mY

1mV

0.01V

0.1V

1#A

10pA

100pA

10mA

0.1£2

1£2

0.01k£!

0.1k£!

1k£!

10mV

Accuracy

+(0.5% reading + 2 digits)

+(1.2% reading + 10 digits

(50/60Hz)

+(1.0% reading + 2 digits)

+(1.2% reading + 2 digits)

+(2.0% reading + 2 digits)

+(0.8% reading + 2 digits)

+(1.0% reading + 2 digits)

NOTE: Accuracy specifications consist of two elements:

• (% reading) - This is the accuracy of the measurement circuit.

• (+ digits) - This is the accuracy of the analog to digital converter.

NOTE: Accuracy is stated at 65°F to 83°F (18°C to 28°C) and less than

75% RH.

Diode Test

Continuity Check

Battery Test current

Input Impedance

ACV Bandwidth

DCA voltage drop

Display

Overrange indication

Polarity

Measurement Rate

Low Battery Indication

Battery

Fuses

Operating Temperature

Storage Temperature

Operating Humidity

Storage Humidity

Operating Altitude

Weight

Size

Safety

Test current of 1mA maximum, open circuit

voltage 2.8V DC typical

Audible signal will sound if the resistance is

less than approximately 30£2

9V (6mA); 1.5V (100mA)

>IM_

45Hz to 450Hz

200mV

3 ½ digit, 2000 count LCD, 0.5" digits

"1" is displayed

Automatic (no indication for positive polarity);

Minus (-) sign for negative polarity.

2 times per second, nominal

"BAT" is displayed if battery voltage drops

below operating voltage

one 9 volt (NEDA 1604) battery

mA, pA ranges; 0.2A/250V fast blow

A range; 10A/250V fast blow

41°F to 104°F (5°C to 40°C)

-4°F to 140°F (-20°C to 60°C)

Max 80% up to 87°F (31°C) decreasing linearly

to 50% at 104°F (40°C)

<80%

7000ft. (2000) meters maximum.

9.17 oz. (260g).

4.78" x 2.38" x 1.57" (121.5mm x 60.6mm x

40mm)

For indoor use and in accordance with

Overvoltage Category II, Pollution Degree 2.

Category II includes local level, appliance,

portable equipment, etc., with transient

overvoltages less than Overvoltage Category Ill.

iWARNING: To avoid electric shock, disconnect the test leads from any I

source of voltage before removing the battery door. I

Disconnect the test leads from the meter.

Remove the protective rubber holster (if installed).--_._

Open the battery door by loosening the screw using a

Phillips head screwdriver.

Insert the battery into battery holder, observing the

correct polarity.

Put the battery door back in place. Secure with the

screw.

iWARNING: To avoid electric shock, do not operate the meter until the Ibattery door is in place and fastened securely. I

NOTE: If your meter does not work properly, check the fuses and batteries

to make sure that they are still good and that they are properly inserted.

e]".,l=1t.,f-I III_JellI__."11IIt.|l[_l i [e]__

JWARNING: Risk of electrocution. High-voltage circuits, both AC and DC, Jare very dangerous and should be measured with great care. I

1. ALWAYS turn the function switch to the OFF position when the meter is

not in use.

2. If "OL" appears in the display during a measurement, the value exceeds

the range you have selected. Change to a higher range.

NOTE: On some low AC and DC voltage ranges, with the test leads not

connected to a device, the display may show a random, changing reading.

This is normal and is caused by the high-input sensitivity. The reading will

stabilize and give a proper measurement when connected to a circuit.

DC VOLTAGE MEASUREMENTS

J AUTION: Do not measure DC voltages if a motor on the circuit is

being switched ON or OFF. Large voltage surges may occur that can

damage the meter.

1. Set the function switch to the highest V DC _---

position

2. Insert the black test lead banana plug into the _ I

negative (COM) jack. •................

Insert the red test lead banana plug into the _')i,

positive (V) jack.

3. Touch the black test probe tip to the negative side _/i

of the circuit. /_j _t'_/.

Touch the red test probe tip to the positive side of .......

the circuit.

4. Read the voltage in the display. Reset the

function switch to successively lower V DC

positions to obtain a higher resolution reading.

The display will indicate the proper decimal point and value. If the

polarity is reversed, the display will show (-) minus before the value.

Andere Handbücher für 82140

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Craftsman Messgerät Handbücher

Craftsman

Craftsman 320.48298 Bedienungsanleitung

Craftsman

Craftsman 320.29939 Bedienungsanleitung

Craftsman

Craftsman CMHT77621 Bedienungsanleitung

Craftsman

Craftsman 82369 Bedienungsanleitung

Craftsman

Craftsman 320 Series Bedienungsanleitung

Craftsman

Craftsman 73756 Bedienungsanleitung

Craftsman

Craftsman CMHT77639 Bedienungsanleitung

Craftsman

Craftsman 82140 Bedienungsanleitung

Craftsman

Craftsman 320.48277 Bedienungsanleitung

Craftsman

Craftsman 25466 Bedienungsanleitung

Craftsman

Craftsman CMHT77637 Bedienungsanleitung

Craftsman

Craftsman 161.210400 Bedienungsanleitung

Craftsman

Craftsman 19741 Bedienungsanleitung

Craftsman

Craftsman CMHT77638 Bedienungsanleitung

Craftsman

Craftsman 82028 Bedienungsanleitung

Craftsman

Craftsman 82017 Bedienungsanleitung

Craftsman

Craftsman CMHT77620 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung