CRE Technology PM-PROGRESS Leitfaden

MULTIFUNCTION POWER

METER

Technical Documentation

PM-PROGRESS

Part Number:

PMP

CRE Technology

130, Allée Victor Naudin

Zone des Templier

Sophia-Antipolis

06410 Biot

FRANCE

Phone: +33 (0)4 92 38 86 82

Fax: +33 (0)4 92 38 86 83

Website: www.cretechnology.com

Email: info@cretechnology.com

NOTE

Read this entire manual and all other publications pertaining to the work to be performed

before installing, operating, or servicing this equipment. Apply all plant and safety

instructions and precautions. Failure to follow instructions can cause personal injury and/or

property damage.

Motors, turbines and any other type of generator must be equipped with protections

(overspeed, high temperature, low pressure…) depending on the power plant.

Any changes of the normal use of the equipment can cause human and material damage.

For further information, please contact your CRE Technology distributor or the After-Sales Service Team.

All CRE Technology products are delivered with one year warranty, and if necessary we will be happy to come

on site for product commissioning or troubleshooting. The company also provide specific trainings on our

products and softwares.

Technical support: +33 (0)4 92 38 86 86 (office hours: 8.30AM-12AM / 2PM-6PM GMT+1).

Email: support@cretechnology.com

SKYPE: support-cretechnology.com

INFORMATION

You can download the most up-to-date version of this documentation and different

other documentations relating to CRE Technology products on our Web site

http://www.cretechnology.com.

CRE Technology believes that all information provided herein is correct and reliable and reserves the right to

update at any time. CRE Technology does not assume any responsibility for its use.

Technical documentation history

Date

Version

Comments

2011

Initial version.

Dec. 2015

Added details about internal current connection.

Typos.

Documentations available on CRE Technology Web site:

pmp-sales-documentation.pdf

pmp-technical-documentation.pdf

pmp-documentation-commerciale.pdf

Table content

1INSTALLATION AND OPERATING INSTRUCTION....................................................................................................... 1

1.1 MEASUREMENT ................................................................................................................................................... 1

1.2 SETTING UP......................................................................................................................................................... 1

1.3 SETUP MENU STRUCTURE ....................................................................................................................................... 2

1.4 MENU OPTION SELECTION ...................................................................................................................................... 3

1.5 INSTALLATION...................................................................................................................................................... 4

1.5.1 Single phase, two wire ................................................................................................................................. 4

1.5.2 Three phase, three wire ............................................................................................................................... 5

1.5.3 Three phase, four wire ................................................................................................................................. 5

1.5.4 Cut-out details............................................................................................................................................. 6

1.5.5 Wiring ......................................................................................................................................................... 6

2PM-PROGRESS MODBUS PROTOCOL IMPLEMENTATION......................................................................................... 8

2.1 MODBUS PROTOCOL OVERVIEW ............................................................................................................................... 8

2.2 INPUT REGISTERS .................................................................................................................................................. 9

2.2.1 PM-progress input registers......................................................................................................................... 9

2.3 MODBUS PROTOCOL HOLDING REGISTERS AND DIGITAL METER SET UP ............................................................................ 11

2.3.1 PM-progress MODBUS Protocol Holding Register Parameters .................................................................... 11

3R5485 GENERAL INFORMATION ............................................................................................................................ 14

3.1 HALF DUPLEX .................................................................................................................................................... 14

3.2 CONNECTING THE INSTRUMENTS ............................................................................................................................ 14

3.3 AAND BTERMINALS ........................................................................................................................................... 15

3.4 TROUBLESHOOTING ............................................................................................................................................ 16

4MAINTENANCE AND SAFETY REQUIREMENT ......................................................................................................... 17

4.1 MAINTENANCE .................................................................................................................................................. 17

4.2 SAFETY ............................................................................................................................................................ 17

4.3 EMC INSTALLATION REQUIREMENT......................................................................................................................... 17

5CRE TECHNOLOGY ................................................................................................................................................. 18

Figures

Figure 1 - Single phase, two wire....................................................................................................................................... 4

Figure 2 - Three phase, three wire..................................................................................................................................... 5

Figure 3 - Three phase, four wire....................................................................................................................................... 5

Figure 4 –Case dimensions and Cut-out details................................................................................................................. 6

Figure 5 –Modbus via RS485 network overview.............................................................................................................. 15

Figure 6 –Recommended wiring..................................................................................................................................... 15

Figure 7 –A and B terminal............................................................................................................................................. 15

Figure 9 –Access to CRE Technology............................................................................................................................... 18

Figure 10 - CRE Technology distributors .......................................................................................................................... 19

Tables

Table 1 - Measurement..................................................................................................................................................... 1

Table 2 - PM-Progress input registers.............................................................................................................................. 10

Table 3 –PM-progress modbus protocol holding register parameters ............................................................................. 12

Table 4 –R5485 General Information.............................................................................................................................. 14

PMP 9 0020 B EN –Technical documentation

Chapter : Installation and operating instruction

1Installation and operating instruction

PM-Progress is designed for accurate measurement and display of all major electrical and power quality

parameters, in single-phase two wire, and three-phase three and four-wire system configurations.

This manual provides all the necessary instructions to safely install and operate the instrument. For more

information please contact your distributor.

1.1

Measurement

In measurement mode, the buttons control the displayed measurement as follows:

Used to select the Voltage and Frequency

display screens.

In set-up mode this is the “Back” button.

Used to select the Current display screens.

In set-up mode this is the “Up” button.

Used to select the Power and Power Factor

display screens.

In set-up mode this is the “Down” button.

Used to select the Energy display screens.

In set-up mode this is the “Enter” button.

Table 1 - Measurement

1.2

Setting up

Press and hold the two buttons and simultaneously for five seconds until the password

screen is displayed.

Press four times to enter the default password of “0000”.

PMP 9 0020 B EN –Technical documentation

Chapter : Installation and operating instruction

The system setup screen will be displayed on the screen. Press the button to scroll down the

menu until you see the CT primary setting screen.

Press the button to enter the CT primary setting screen. The first digit should start flashing.

Use and buttons to set the digit to the required level then press to confirm. Repeat

this process until all four digits have been set to the desired CT primary value. (e.g. 100A = 0100A,

1000A = 1000A).

The word “SET” should be displayed after the fourth digit has been entered to confirm that the

primary CT value has been set.

Press to return to the first level menu structure, to scroll up and down the structure to adjust

other parameters (if needed). If no other settings are required, press to exit set-up mode and

return to measurement mode.

1.3

Setup menu structure

Change password:

nnnn - 4-digit number –default ‘0000’

Supply systems:

3-phase (3 or 4-wire) or Single phase

CT:

Set maximum current that can be monitored according to CT in use. nnnn –4-digit number 0001 to 9999.

Demand Interval Time:

Selects demand time in minutes from 60/30/20/15/10/8/5/OFF.

PMP 9 0020 B EN –Technical documentation

Chapter : Installation and operating instruction

Reset:

Reset cumulative energy and Demand measurements to zero.

Communication parameters:

For RS485 interface (optional), Modbus protocol

Baud rate 2400/4800/9600/19200/38400

Parity none/odd/even

Stop bits 1 (1 or 2 if parity is none)

RS485 network address nnn –3-digit number 1 to 247

Order –Norm/Rev indicates if the Modbus word order is normal or reversed.

Johnson Controls (JC) N2 protocol

RS485 network address nnn –3-digit number 1 to 255.

Relay pulse outputs (optional):

OP1 kWh/kVArh (Active/reactive)

Import from output module 1

OP2 kWh/kVArh (Active/reactive)

Import from output module 2

Rate 0.1/1/10/100/1000 kWh or kVArh per pulse

Pulse width 200/100/60 ms.

Energy:

kilo/Mega

Test:

Phase sequence

Display on –all elements on to check display

Display toggle - Each element is turned on and off

SOFT:

Displays software version number.

1.4

Menu option selection

After entering the correct password, use and buttons to navigate up and down the first

level until the desired parameter is reached. Selection does not roll over from bottom to top of list

or vice versa.

PMP 9 0020 B EN –Technical documentation

Chapter : Installation and operating instruction

Press button to select the desired parameter and enter the second level menu structure.

If an item flashes, then it can be adjusted by and keys. If not, there may be a further layer,

e.g. Comms - Baud rate, before adjustment is possible. Press to select the lower layer.

Having selected an option from the current menu layer, press to confirm your selection. The

word SET will come on.

Once all the necessary selections have been made and the required settings entered, press to

return to the first level menu structure. The word SET will turn off and you can then use

and keys for further menu selection.

On completion of all settings, press repeatedly to exit set-up mode and return to measurement

mode.

1.5

Installation

1.5.1

Single phase, two wire

Figure 1 - Single phase, two wire

PMP 9 0020 B EN –Technical documentation

Chapter : Installation and operating instruction

1.5.2

Three phase, three wire

Negative current inputs are

internally connected together.

Figure 2 - Three phase, three wire

1.5.3

Three phase, four wire

Negative current inputs are

internally connected together.

Figure 3 - Three phase, four wire

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CRE Technology Messgerät Handbücher

CRE Technology

CRE Technology BSD 2.0 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung