CREE LIGHTING Cadiant Bedienungsanleitung

Cadiant Dynamic Skylight Quick Start Guide

Last Modified on 01/24/2022 9:08 am EST

INTRODUCTION

Use these instructions to set up:

A single or multiple Cadiant™ Dynamic Skylights

Other new SmartCast fixtures (CR Series troffers, etc.) in the same space to be associated with the

Cadiant™ fixtures

The SmartCast Wireless Gateway and SmartCast Touchscreen used to control the fixtures

PREPARATIONS

Should you have existing SmartCast fixtures, please ensure that you have installed the latest software update

before proceeding.

At this point, the following devices should be installed

and powered on:

Cadiant™ Dynamic Skylight - one or multiple

SmartCast Touchscreen

SmartCast Wireless Gateway with WiFi (SWG-WiFi)

Other SmartCast luminaires to be grouped

(optional)

SmartCast Wall Controller (dimmer) (optional)

Also required: SmartCast Configuration Tool

Locate the SWG-WiFi before beginningLocate the SWG-WiFi before beginning

commissioning.commissioning. You’ll need a line of sight to the device

® ®

commissioning.commissioning. You’ll need a line of sight to the device

to properly commission it with the Configuration Tool. The

SWG-WiFi may be attached to the ceiling grid, installed

above the ceiling, or wall-mounted.

Locate the SSID number and password for theLocate the SSID number and password for the

SmartCastSmartCast Wireless Gateway. Wireless Gateway. Please ensure

the installer records the SSID and password from the

sticker on the back of the device prior to installation.

(Note: if the SSID and password were not recorded at

the time of installation you will need to capture that

information from the back of the device before

continuing.)

(Note: if this label is not present on the SmartCast

Wireless Gateway, use the information on the

Manufacturer's label. The alphanumeric code below the

bar code is the MAC address of the SmartCast Wireless

Gateway. Remove the colons and make all letters

lowercase to convert the MAC address to the unit

password.)

Device StatusDevice Status

When you begin, make sure:

Lights are ONON and not set up or commissioned.

Touchscreen tablet is ONON, reading "Welcome - Get"Welcome - Get

Started"Started"

SmartCast® Wireless Gateway is on. Center LED is

blue and flashing in a two-blink pattern.

STEP 1: SET UP THE SMARTCAST NETWORK

®®

POWER ON POWER ON the Configuration Tool.

Wait for the Configuration Tool to read:

The display will indicate that the Configuration Tool is

ready to begin OneButton™ Setup.

Press OK OK to begin commissioning the SmartCast

network.

However, if the Configuration Tool finds existing

networks, the display will read:

Use the Configuration tool direction arrows to highlight

Set Up New Set Up New and click OKOK. Even if new networks are

found, we recommend using the Set Up New Set Up New feature.

The display will instruct you to place the Configuration

Tool down on a level surface while conducting OneButton

Setup.

During OneButton Setup, the luminaires and dimmers are

performing the following functions to automatically

commission themselves.

1. Formation of a secure wireless network

2. Sensor Self-calibration for daylight harvesting

3. Learning about the spaces in which they are installed

4. Automatic grouping of the devices based on where

they are installed

This process ranges from a few minutes up to one hour

depending on the number of devices being set up. Please

do not proceed until the device states that OneButton™ is

complete.

Once the Configuration Tool display indicates that

OneButton™ Setup is complete, press OKOK to confirm.

The luminaires and dimmers in the lighting network are

set up and functional. Dimmers will control the luminaires

they're grouped with. Luminaires will share motion

information and daylight harvesting. The SmartCast

Wireless Gateway and SmartCast Touchscreen will not be

fully set up yet.

To ensure the optimal installation, the luminaires and

dimmers should be configured in the final desired zones

and configurations.

If your project requires multiple control zones, use the

Configuration Tool to set them up at this point. It is best to

have these assigned prior to adding the SmartCast®

Wireless Gateway to the network.

Configure all zones and fixtures settings before

proceeding.

Please refer to the SmartCast Wireless Deployment

Guide for more information.

STEP 2: SET UP THE SMARTCAST WIRELESS GATEWAY

On the Main Menu of the Configuration Tool, use

the arrow keys to select Advanced Advanced and press the OKOK

button.

2 2

On the Advanced menu, use the arrow keys to select

Add GatewayAdd Gateway, then press the OKOK button.

3 3

The display will ask you to select the device to add.

Use the arrow keys to select Gateway with WiFi Gateway with WiFi and

press the OKOK button.

4 4

The Configuration Tool display will read:

Follow the instructions on the Configuration Tool

screen.

5 5

Point the Configuration Tool at the SmartCast

Wireless Gateway until the flashing blue LED becomes

a steady green.

The Configuration Tool will shine a green flashlight

beam in the direction it is pointed to aid in targeting the

SWG-WiFi.

(This may take up to 10 seconds.)

6 6

At this point, the Configuration Tool display will

indicate that the SWG has been added to the network.

Press the OKOK button.

The SmartCast

Wireless Gateway with WiFi has

now been added to the network.

STEP 3: SET UP THE SMARTCAST TOUCHSCREEN

The Touchscreen display should read:

The Touchscreen display will change to the

screen on the right.

The Touchscreen display will show available

SmartCast Wireless Gateways with WiFi. Find the

matching SSID per the label on the back of the

SmartCast Wireless Gateway with WiFi (recorded in

previous steps) and tap the corresponding SSID in

the list. In this example, we are using

SmartCast_SWG_a4c2.

The Touchscreen will ask you to enter the

SmartCast Wireless Gateway password using an

onscreen keyboard.

Use the password from the label and press

Connect.Connect.

The Touchscreen display will return to the

Connect to GatewayConnect to Gateway screen.

6 6

The Touchscreen display will ask you to choose

you time zone.

Select the desired time zone. The selection will

then appear above the Continue Continue button.

If the selection is correct, press Continue.Continue.

Next, the SmartCast Touchscreen will display a

look like:

For Username, enter admin admin (lowercase).

For Password, enter the same password used in

Step 4 of this section. This is the password found

on the label on the backside of the SWG. Once the

password has been typed, press "Done""Done" on the

keypad.

Then press "Submit"."Submit".

You will then be asked to choose a 6-digit

admin PIN.admin PIN.

(Record your admin PIN in a secure location.

You will use it to change settings in the future.)

1010

You'll be asked to re-enter the admin PIN admin PIN to

confirm it.

1111

The SmartCast Touchscreen will then display

all the lighting spaces in the lighting network

available to the SmartCast Wireless Gateway you

have logged into.

It will ask you to select those lighting spaces you

want to control with the Touchscreen. (You can

change these spaces in the Advanced menu.) ToTo

identify the fixtures in spaces you want toidentify the fixtures in spaces you want to

controlcontrol, press and hold the button, and then look for

flashing fixtures.

A long press on a lighting space will identify it by

flashing / dimming the lights associated with that

group. The button will change color when pressed

correctly.

A short press highlights the lighting space and

includes it as a space to be controlled by the

Touchscreen.

1212

Once you have selected all the lighting spaces

to be controlled by the Touchscreen, press

ContinueContinue. In our example, Space 1 and Space 4 are

selected.

1313

Next, you'll be asked to name the Touchscreen

using an onscreen keyboard. This is the name that

will appear on the Touchscreen's default (displayed

when a user has not been interacting with the

Dieses Handbuch passt für folgende Modelle

Andere CREE LIGHTING Beleuchtungsausrüstung Handbücher

CREE LIGHTING

CREE LIGHTING FLEX Series Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING DOT Series Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING CONNECTED MAX Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING SmartCast Touchscreen Control Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING ZR Series Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING SmartCast Kurzanleitung

CREE LIGHTING

CREE LIGHTING Noctura Series Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING RUL-B Series Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING VG Series Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING CONNECTED MAX Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING OSQ Series Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING SMK-CR14 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING THE EDGE ARE-EDG-DA Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING Stylus Series Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING L1-12 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING FLX Series Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING ZR Series Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING XSP Series Montageanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung

LCG

LCG Thunder 400 Bedienungsanleitung