CREE LIGHTING SmartCast Kurzanleitung

SmartCast Wireless Deployment Guide

Last Modified on 08/03/2021 3:53 pm EDT

WELCOME TO CREE SMARTCASTWELCOME TO CREE SMARTCAST TECHNOLOGY TECHNOLOGY

For years, bringing smart control to the lighting environment meant two sets of wires: one for power, one for

control. That's two trips up the ladder, two wiring diagrams and two times the complexity. Even with newer

wireless control technologies, installers still have to contend with extra equipment and complicated

commissioning procedures.

Cree SmartCast Technology delivers essential lighting control without the extra design, installation and setup

time typical of traditional lighting control systems. With SmartCast Technology, installers simply wire the

fixtures for power and commission the entire system with the touch of one button.

This guide will take you through the deployment of SmartCast Technology. You'll see how easy it is to design,

install, and commission a code-compliant lighting system with OneButton™ Setup and SmartCast Technology.

WHAT IS CREE SMARTCASTWHAT IS CREE SMARTCAST TECHNOLOGY? TECHNOLOGY?

Instead of wires, SmartCast Technology uses a network of wireless radio signals (IEEE 802.15.4) to link

fixtures, sensors and controls into a connected and responsive lighting system,. Sensors are built directly into

the fixtures, and whole system comes to life and connects itself together with one touch of the SmartCast

Technology commissioning tool.

SmartCastSmartCast Technology features: Technology features:

Integrated SensorsIntegrated Sensors

SmartCast Technology products

incorporate integrated ambient light

and motion sensors to achieve

energy savings. Embedded sensors

in each luminaire eliminate the need

for up-front sensor layout design and

allow for reliable detection of

occupants and ambient light.

OneButton™ SetupOneButton™ Setup

SmartCast Technology luminaire

and dimmers automatically create

intelligent groupings with OneButton

Setup. The result is smart lighting

that meets existing and emerging

building codes and installs and sets

up easier than comparable lighting

controls systems

SmartCast Technology luminaires

and controls required minimal

®®

Wireless CommunicationWireless Communication

and controls required minimal

additional labor to install compared

to non-dimming solutions. In new

construction and upgrade

applications, installers can rely on a

secure wireless communication

between luminaires and dimmers

eliminating the need for control

wiring.

ONEBUTTON™ SETUPONEBUTTON™ SETUP

Once the SmartCast Technology luminaires and switches are installed and wired for power, the OneButton™

Setup process is started using the Configuration Tool. OneButton™ Setup establishes a network for all devices

within range. A network can comprise up to 250 individual devices (luminaires, switches, plug load controllers,

and 0-10V controllers). Because the network is wireless, in can include devices in different rooms, floors and

building within range.

After forming the network, OneButton™ Setup automatically organizes individual devices into groups based on

the layout of the space. For instance, the devices in a conference room are controlled as a group separately

from the devices in the corridor outside, which form their own group. Yet, both groups are part of the same

SmartCast Technology network.

Like any wired lighting control environment, some lighting groups are controlled manually by dimmers and

switches, and others are controlled automatically by motion sensors. In a SmartCast Technology Installation,

these are called "switch groups" and "occupancy groups," which OneButton™ Setup creates automatically.

PLANNING ONEBUTTON™ SETUPPLANNING ONEBUTTON™ SETUP

Before you begin OneButton™ Setup, it's important to plan how the networks will be deployed. When planningBefore you begin OneButton™ Setup, it's important to plan how the networks will be deployed. When planning

SmartCastSmartCast Technology networks, be sure to consider the use of the spaces and what devices will be grouped Technology networks, be sure to consider the use of the spaces and what devices will be grouped

together. Devices in different networks cannot be grouped together.together. Devices in different networks cannot be grouped together.

Make sure all SmartCast Technology devices are installed and powered according to the installation

instructions. All devices should be receiving constant, unswitched AC power. All prior occupancy sensors and

traditional dimmers/switches should be bypassed and/or removed.

Note:Note: SmartCast Technology may be used with relay panels or contactors, but it is strongly recommended that

these systems be bypassed. SmartCast Technology setup, operation and maintenance operate more reliably

when all devices are on unswitched power. In-wall motion sensors switches must be removed or bypassed.

When a device is ready for OneButton™ Setup, it will show a 2-blink sequence on the status LED. During

OneButton™ Setup, the status LEDs will transition through various modes until devices are placed into their

normal operating mode (1-blink). On luminaires, the status LED will automatically blink. On switches, the LED will

blink when a button is pressed. For details on the location of the status LED, refer to the installation instructions

for the device.

®®

Figure A: Device Blink PatternsFigure A: Device Blink Patterns

Status LED IndicatorStatus LED Indicator Operating ModeOperating Mode

1 Blink1 Blink Set up and in normal operation

2 Blinks2 Blinks Ready for OneButton Setup

3 Blinks3 Blinks OneButton Setup in process

4 Blinks4 Blinks Select mode

5 Blinks, Solid or Off5 Blinks, Solid or Off Error - contact Cree Customer Service

MULTIPLE NETWORKSMULTIPLE NETWORKS

When you form a network with OneButton™ Setup, all devices that are powered on, in range and not in an existing

network are added to the new network. After joining a network, they will not be added to networks formed by

subsequent OneButton™ Setups.

If you are setting up more than one SmartCastIf you are setting up more than one SmartCast Technology network, each network must be set up one at a Technology network, each network must be set up one at a

time. time.

This network-by-network deployment can be performed in two ways: Install the first network, commission

the first network, then install the second network, commission the second network, etc. Or, you can install all

fixtures for all networks, and use circuit breakers to power and set up one network at a time.

PERFORMANCE CONSIDERATIONSPERFORMANCE CONSIDERATIONS

Network size and group size: Network size and group size:

While SmartCast Technology is designed for networks with up to 250 devices and

groups with up to 100 devices, you can achieve the optimal balance of speed, responsiveness and network size

when networks comprise 100 to 125 devices. To help you decide how many networks to set up for your project,

consider the guidelines in

Figure BFigure B

Physical network constraints: Physical network constraints:

SmartCast Technology networks are similar to other wireless networks such as

WiFi networks; distance and obstructions between devices can decrease speed and responsiveness. SmartCast

Technology does a great job automatically determining lighting groups and light levels, but you can make sure

you're getting the most out of the system when you plan ahead and take physical constraints, like walls and

open space into consideration. For guidance on planning for physical obstructions, consider the guidelines in

Figure C.Figure C.

Figure B: Network Size GuidelinesFigure B: Network Size Guidelines Figure C: Physical Constraint GuidelinesFigure C: Physical Constraint Guidelines

Large (Over 150)Large (Over 150) DistanceDistance

Pros:Pros:

When several devices are located within 30 ft. of each

other, they can be considered tightly grouped. Large

distances between devices or groups of devices affect

available communication paths and signal strength and

should be broken into multiple networks with each cluster

as a network.

Fewer networks to commission

Faster network selection from Configuration

Tool

Cons:Cons:

Configuration Tool takes longer to reconnect

to existing network(s)

Longer response times to settings or group

IInternal Wallsnternal Walls

Depending on their material, internal walls can attenuate

or weaken wireless signals. Where possible, limit

®®

changes

More devices (and occupants) affected

during any change

networks to no more than three internal walls between

the Configuration Tool and any one device. Avoid

crossing any solid, all-metal walls within a network, and

keep the Configuration Tool centrally located in the space

during OneButton Setup

Medium (50-150)Medium (50-150)

Best balance between responsiveness,Best balance between responsiveness,

performance and Configuration Toolperformance and Configuration Tool

rediscoveryrediscovery

External WallsExternal Walls

External walls are typically more densely constructed

than internal walls and can attenuate wireless signals

more than internal walls. Limit network setup to within

external walls. If network boundaries could cross external

walls, it is advised to create multiple networks. Keep the

Configuration Tool centrally located in the space during

OneButton Setup.

Small (Under 50)Small (Under 50)

Pros:Pros: Internal Floor/CeilingInternal Floor/Ceiling

Fast network selection

Faster response times to settings or groups

changes

Fewer devices (and occupants) affected

during any change

External walls, floors and ceilings are often densely

constructed and can attenuate wireless signals. Further,

it may not be intuitive to those performing maintenance

that a network spans multiple floors. If network

boundaries could cross floors, it is advised to create

multiple networks and limit each network to a single

floor.

Cons:Cons:

More steps required to set up a large space

May cause network selection from the

Configuration Tool to be slow

May not be feasible for large open areas with

many devices

Figure B: Network Size GuidelinesFigure B: Network Size Guidelines Figure C: Physical Constraint GuidelinesFigure C: Physical Constraint Guidelines

PERFORMING ONEBUTTON™ SETUPPERFORMING ONEBUTTON™ SETUP

Start by counting the devices (fixtures and switches) to be included in the network. Ensure they are powered on;

fixtures should be at full brightness and switches should flash their LED twice when a button is pressed. Stand

in the center of the planned network, power on the SmartCast Technology Configuration Tool and allow it to

search for existing networks. Only one Configuration Tool should be operated at a time.

If no existing networks are found, press "OK""OK" to start OneButton™ Setup. If any existing networks are discovered,

the Configuration Tool will present the option to Edit ExistingEdit Existing or Set Up NewSet Up New. To add new devices to an existing

network, select Edit ExistinEdit Existingg. To set up a new network and with new devices, select Set Up NewSet Up New. Press "OK""OK" on

the Configuration Tool to begin OneButton Setup™.

As fixtures are identified and added to the new SmartCast Technology network, they will dim down. The status

LED on all devices in the system (fixtures and switches) will begin showing a 3-blink sequence.

As OneButton™ Setup adds fixtures and switches to the network, compare the number of devices found and

reported on the Configuration Tool with the number of devices you previously continued.

During daylight harvesting calibration, all fixtures that are part of the network will turn off. The Configuration

Tool will indicate when the lights are supposed to be off. Any fixtures that stay at full brightness for the whole

OneButton™ Setup process are not part of the newly created network. OneButton™ Setup will continue with all

available devices. After the Configuration Tool indicates that OneButton™ Setup is complete, the troubleshooting

actions that follow in

Figure DFigure D

can be attempted.

Figure D:Figure D:

If devices are missing from the new network, or if too many joined, you can correct the issue as follows:If devices are missing from the new network, or if too many joined, you can correct the issue as follows:

Problem: All devices were not foundProblem: All devices were not found

SymptomSymptom Potential CausePotential Cause SolutionSolution

Status LED is blinking

two times. Device(s) missed the join process.

Connect Configuration Tool to the

existing network, if not already

connected. Perform Add New Devices

from the Advanced menu.

Status LED is blinking

three or four times.

Device(s) needs to be reset.

Device did not complete OneButton Setup.

Connect Configuration Tool to the

existing network, if not already

connected. Use Reset Device from the

Advanced menu to reset the device. If the

devices cannot be reset using the

Configuration Tool, follow the manual

reset procedure on the installation sheet.

If possible, cycle power after manual

reset. After reset, confirm Status LED is

blinking twice. Connect Configuration

Tool to the existing network, if not already

connected. Perform Add New Devices

from the Advanced menu. If problem

continues, cycle power and try again.

Problem: Too many devices were foundProblem: Too many devices were found

Unintended device

was found during

OneButton Setup

More devices than expected were

powered and ins range with their Status

LED blinking twice.

Connect Configuration Tool to the

existing network, if not already

connected. Use Reset Device from the

Advanced menu to reset the extra

device(s) on the network.

Problem: SmartCastProblem: SmartCast Technology Configuration Tool cannot discover all network devices; "found x of y Technology Configuration Tool cannot discover all network devices; "found x of y

®®

devices."devices."

Rediscover Devices

won't find missing

device(s).

Configuration Tool needs to be centrally

located.

Device is non-responsive.

Relocate to center of network and choose

"Rediscover Devices."

Look for non-powered devices.

Note:Note: Choosing "Go to Main Menu" should only be selected as a last resort. If a device is in-network, was simply

not discovered and this option was selected, Add Device can assign duplicate addresses. This can lead to

unpredictable system behavior.

Problem: SmartCastProblem: SmartCast Technology Configuration Tool displays a warning that it cannot discover all network Technology Configuration Tool displays a warning that it cannot discover all network

devices.devices.

Discover Network

Devices reports

missing devices.

Configuration Tool is not located such

that it can communicate with all devices.

Missing device is not responding.

Move Configuration Tool so it is centrally

located within devices on the network.

Select "Rediscover Devices."

Verify missing device has power. If the

missing device is a luminaire, verify that

the SmartCast Technology Control

Module is powered and its Status LED

illuminates.

Note:Note: If the Configuration Tool reports missing devices, "Go to Main Menu" should only be selected after

attempting to correct the issue using the above methods. If the device is communicating in the network but not

discovered by the Configuration Tool, continuing to the Main Menu may allow for duplicate device addresses

which may cause unpredictable system behavior.

VERIFYING ONEBUTTON™ SETUPVERIFYING ONEBUTTON™ SETUP

At the conclusion of OneButton™ Setup, spaces should be tested for proper grouping and operation. To perform

verification of the new SmartCast Technology installation, follow these steps:

Confirm proper grouping:Confirm proper grouping:

GroupGroup

TypeType DefinitionDefinition CheckCheck TipsTips

SwitchSwitch

A group of fixtures that

are controlled by one or

more switches.

With the system in normal mode

(Configuration Tool off or on

main menu), use the

on/off/raise/lower paddles on

wall switch to determine if all

desired fixtures are controlled.

If the fixtures are being dimmed

due to daylight harvesting, they

may not be able to be raised, but

will be able to be turned off and

on.

®®

OccupancyOccupancy

A group of fixtures that

act together in response

to motion events within

the group.

Connect the Configuration Tool

to the network, if not already

connected. Navigate to Device

Settings Occupancy and select

Set Occupied Level. The

Configuration Tool will prompt

you to select a group after which

fixtures in the group will turn off.

Select the Back button once

group is confirmed.

Don't advance past the screen

indicating a group was selected

until the group has been verified.

Depending on the setting

selected, fixtures may change

levels.

Adjust grouping if necessary. Making changes to the switch group will not affect the occupancy group, and vice-Adjust grouping if necessary. Making changes to the switch group will not affect the occupancy group, and vice-

versa.versa.

GroupGroup

OperationOperation BehaviorBehavior SettingsSettings

CreateCreate Select each device to assign to a group. Previous

grouping will be overridden. Assign defaults.

Add DeviceAdd Device

Select an existing group and add selected devices to

that group. Device to add must be part of the network

the Configuration Tool is connected to.

New device inherits settings from

group.

MMergeerge Select one or more groups to combine into a single

group. Assign defaults.

UngroupUngroup

Select an occupancy group to dissolve; each fixture

becomes its own group. This operation only applies to

occupancy groups.

Maintain existing settings.

Adjusting default settings, if necessary:Adjusting default settings, if necessary:

SmartCast Technology groups share a collection of settings that define their behavior. Each of these settings

has a default value but can be changed.

SettingSetting DefaultDefault ModificationModification

Control ModeControl Mode

Dimmer in group - Manual On,

Auto Off

Device Settings

→

Occupancy

→

Set Mode

No Dimmer in group - Auto On,

Auto Off

Occupied LevelOccupied Level 100% Device Settings

→

Occupancy

→

Set Occupied Level

UnoccupiedUnoccupied

LevelLevel 0% Device Settings

→

Occupancy

→

Set Unoccupied

Level

OccupancyOccupancy

SensitivitySensitivity HIGH Device Settings

→

Occupancy

→

Set Sensitivity

OccupancyOccupancy

TimeoutTimeout 20 minutes Device Settings

→

Occupancy

→

Set Timeout

MinimumMinimum

Daylighting LevelDaylighting Level 5% Device Settings

→

Daylighting

→

Set Min Level

Verify occupancy sensors.Verify occupancy sensors.

To test that each sensor is functioning properly, select "Test Occupancy" mode from the Configuration Tool.

You will be prompted to select the occupancy group you want to test, at which point the group will enter a test

mode where each fixture within the group acts only on its own motion sensor and is assigned a 30-second

timeout. While the fixtures remain in this mode, you will verify that each fixture times out after approximately 30

seconds on no motion, remains off for a brief period of time (e.g., 30 seconds to 1 minute of no motion), and

then turns on again due to motion events detected by the fixture.

Once all occupancy sensors in the group have been verified, select "OK" "OK" on the Configuration Tool. If you identify

a problematic fixture (e.g., it won't time out or triggers falsely), you can adjust sensitivity for the group using the

Configuration Tool, under Device Settings

→

Occupancy

→

Set Sensitivity.

Inhaltsverzeichnis

Andere CREE LIGHTING Beleuchtungsausrüstung Handbücher

CREE LIGHTING

CREE LIGHTING SmartCast Touchscreen Control Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING VG Series Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING FLX Series Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING THE EDGE ARE-EDG-DA Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING Noctura Series Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING Cadiant Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING ZR Series Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING XSP Series Montageanleitung

CREE LIGHTING

CREE LIGHTING RUL-B Series Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING OSQ Series Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING ZR Series Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING CONNECTED MAX Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING FLEX Series Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING SMK-CR14 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING Stylus Series Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING L1-12 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING DOT Series Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING CONNECTED MAX Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung