Crestron 3 Series Bedienungsanleitung

The Crestron® CP3 and CP3N are compact, rack-mountable 3-Series®

automated control processors with numerous integrated control ports.

Featuring the 3-Series control engine, the CP3 and CP3N unify the

disparate technologies in residential, commercial, and government

buildings so that they can communicate and work together intelligently.

The CP3N also supports the Crestron Control Subnet, which is an isolated

gigabit Ethernet network dedicated exclusively to Crestron devices.

NOTE: The CP3 and CP3N are functionally similar. For simplicity within

this guide, the term "control system" is used to refer to both unless

otherwise noted.

In the Box

1 CP3 or CP3N, 3-Series Control System

Additional Items

2 Bracket, Rack Ear, 1U (2032122)

2 Connector, 3-Pin (2003575)

1 Connector, 4-Pin (2003576)

1 Connector, 5-Pin (2003577)

4 Connector, 8-Pin (2003580)

1 Connector, 9-Pin (2003581)

4 Foot, 0.5 in. x 0.5 in. x 0.23 in., Adhesive (2002389)

1 Cable, Power, 5 ft 10 in. (1.78 m) (2042043)

1 Power Pack, 24 VDC, 2.5 A, 100-240 VAC (2045873)

Install the Device

The control system can be mounted into a rack or placed on a flat

surface.

Mount into a Rack

The control system occupies 1U of rack space. Use the three screws from

the front part of each side panel, and a #1 Phillips screwdriver to attach

the two included rack ears to the device, as shown in the following

illustration. Then mount the control system into the rack using four

mounting screws (not included).

Rack Mounting Safety Precautions

Elevated Operating Ambient Temperature: If installed in a closed or

multi-unit rack assembly, the operating ambient temperature of the rack

environment may be greater than room ambient temperature. Therefore,

consideration should be given to installing the equipment in an

CP3 and CP3N QuickStart

3-Series Control System® Automated Processors

environment compatible with the maximum ambient temperature (Tma)

specified by the manufacturer.

Reduced Airflow: Installation of the equipment in a rack should be such

that the amount of airflow required for safe operation of the equipment

is not compromised.

Mechanical Loading: Mounting of the equipment in the rack should be

such that a hazardous condition is not achieved due to uneven mechanical

Circuit Overloading: Consideration should be given to the connection of

the equipment to the supply circuit and the effect that overloading of the

circuits might have on overcurrent protection and supply wiring.

Appropriate consideration of equipment nameplate ratings should be

used when addressing this concern.

Reliable Earthing: Reliable earthing of rack-mounted equipment should be

maintained. Particular attention should be given to supply connections

other than direct connections to the branch circuit (e.g., use of power

strips).

Place on a Flat Surface

Attach the included feet near the corners on the underside of the control

system before placing it onto a flat surface or stacking it with other

equipment.

CP3 and CP3N QuickStart

3-Series Control System® Automated Processors

Connect the Device

Connect the control system as called out in the following illustration.

Connect power last.

When connecting the control system:

lUse Crestron power supplies for Crestron equipment.

lThe control system can be powered with the included 24 VDC power

pack or via Cresnet® network power via the NET 4-pin terminal block

port.

lConnect the chassis ground lug to a known earth ground (for example,

building steel) to ensure the control system is properly grounded.

CP3 and CP3N QuickStart

3-Series Control System® Automated Processors

COM 1 Connections

Port RS-232 RS-4221RS-485

GGND GND GND2

TX TX (from CP3/CP3N) TX- (from CP3/CP3N) TX-/RX-

RX RX (to CP3/CP3N) RX+ (to CP3/CP3N) Not used

RTS RTS (from CP3/CP3N) RTS+ (from CP3/CP3N) TX+/RX+

CTS CTS (to CP3/CP3N) CTS- (to CP3/CP3N) Not used

1. RS-422 transmit and receive are balanced signals that require two lines plus a ground

in each direction. RXD+ and TXD+ should idle high (going low at start of data

transmission). RXD- and TXD- should idle low (going high at the start of data

transmission). If necessary, RXD+/RXD- and TXD+/TXD- may be swapped to maintain

correct signal levels.

2. A ground terminal connection is recommended but not required.

Connect the Control Subnet

(CP3N Only)

The CP3N has a dedicated Control Subnet used for communication

between the control system and Crestron Ethernet devices without

interference from other traffic on the network.

NOTE: Do not connect the CONTROL SUBNET port to the LAN. The

CONTROL SUBNET port must only be connected to Crestron

Ethernet devices.

For more information on using the Control Subnet, refer to the 3-Series

Control System Reference Guide (Doc. 7150) at

www.crestron.com/manuals.

CP3 and CP3N QuickStart

3-Series Control System® Automated Processors

Configure the Device

The control system can be configured using Crestron Toolbox™ software

and the included web-based configuration utility.

To configure the control system:

1. Use the Device Discovery tool in Crestron Toolbox to discover the

control system and its IP address on the network.

2. Use Crestron Toolbox to set the time zone. For more information refer

to the Crestron Toolbox help file.

3. Use a web browser to navigate to http://xxx.xxx.xxx.xxx/setup, where

xxx.xxx.xxx.xxx is the IP address of the control system. The 3-Series

splash page is displayed.

4. Click Setup. The main Setup page is displayed.

The Setup page displays the IP address, hostname, and MAC address of

the control system, as well as a key that is used to register the control

system with the MyCrestron service.

The Setup page also provides access to various setup and programming

pages.

lClick one of the setup selections to configure the applicable device

settings.

lClick the back button on any page to return to the previous page.

CP3 and CP3N QuickStart

3-Series Control System® Automated Processors

Pair the Device with Apple® HomeKit®

Technology

The control system can be paired with an Apple® HomeKit® system, to

enable a TSR-310 handheld touch screen remote to control Apple TV®

devices via a control system program.

NOTES:

lThe control system, the Apple TV device(s), the TSR-310, and the

iOS® device used for setup must all be connected to the same

network.

lThe 3-Series control system must be registered to a MyCrestron

account prior to pairing it with Apple HomeKit. To register the

device, visit https://portal.my.crestron.com, select Add Device

from the Devices tab, and then follow the provided instructions.

lThe 3-Series control system must be connected to the Internet and

must have DNS (Domain Name System) enabled.

To enable the Apple HomeKit functionality on the control system:

1. Open Crestron Toolbox and establish a connection to the control

system.

2. Enable SSL by using the SSL Management function or by issuing the

ssl command in the Text Console tool. for more information refer to

the embedded Crestron Toolbox help files and the 3-Series Control

System Reference Guide (Doc. 7150) at www.crestron.com/manuals.

3. Navigate to the control system Setup page as described in Configure

the Device.

4. Click Apple HomeKit. The Apple HomeKit page is displayed.

5. Click Enable to enable the HomeKit feature on the control system.

6. Click OK to reboot the control system after a reboot confirmation

message is displayed.

7. Return to the main Setup page. A unique eight-digit code is now shown

in the HK Setup Code field.

8. Record the unique eight-digit HomeKit code that is shown next to HK

Setup Code.

For further programming and pairing instructions, refer to the Pairing a

3-Series Control System with Apple HomeKit Technology Programming

Guide (Doc. 8495) at www.crestron.com/manuals.

CP3 and CP3N QuickStart

3-Series Control System® Automated Processors

Connect to Crestron XiO Cloud

Service (Optional)

The Crestron XiO Cloud™ service allows supported Crestron devices

across an enterprise to be managed and configured from one central and

secure location in the cloud. Supported devices are preconfigured to

connect to the service. Use of the service requires a registered Crestron

XiO Cloud account.

NOTE: The device can be disconnected from the service using the

Cloud Services tab in Crestron Toolbox™ software (Functions > Device

Info > Cloud Services). For details, refer to the Crestron Toolbox help

file.

To connect the device to the Crestron XiO Cloud service:

1. Record the MAC address and serial number labeled on the shipping box

or rear panel of the device. The MAC address and serial number are

required in order to add the device to the Crestron XiO Cloud

environment.

2. Do either of the following:

lFor existing accounts, navigate to https://portal.crestron.io.

lFor new accounts, register at www.crestron.com/xiocloud.

3. Claim the device to the service as described in the Crestron XiO Cloud

User Guide (Doc. 8214) at www.crestron.com/manuals.

Visit the Product Page

Scan the QR code to visit the product page.

CP3

www.crestron.com/model/6504877

CP3N

www.crestron.com/model/6505417

CP3 and CP3N QuickStart

3-Series Control System® Automated Processors

Additional Information

Original Instructions

The U.S. English version of this document is the original instructions.

All other languages are a translation of the original instructions.

Crestron product development software is licensed to Crestron dealers and Crestron

Service Providers (CSPs) under a limited nonexclusive, nontransferable Software

Development Tools License Agreement. Crestron product operating system software is

licensed to Crestron dealers, CSPs, and end-users under a separate End-User License

Agreement. Both of these Agreements can be found on the Crestron website at

www.crestron.com/legal/software_license_agreement.

The product warranty can be found at www.crestron.com/warranty.

The specific patents that cover Crestron products are listed at

www.crestron.com/legal/patents.

Certain Crestron products contain open source software. For specific information, visit

www.crestron.com/opensource.

Crestron, the Crestron logo, .3-Series, 3-Series Control System, Cresnet, Crestron

Toolbox, and Crestron XiO Cloud are either trademarks or registered trademarks of

Crestron Electronics, Inc. in the United States and/or other countries. Apple, Apple TV,

and HomeKit are either trademarks or registered trademarks of Apple, Inc. in the

United States and/or other countries. IOS is either a trademark or registered

trademark of Cisco Systems, Inc. in the United States and/or other countries. Other

trademarks, registered trademarks, and trade names may be used in this document

to refer to either the entities claiming the marks and names or their products. Crestron

disclaims any proprietary interest in the marks and names of others. Crestron is not

responsible for errors in typography or photography.

Doc. 7714E

05/08/20

CP3 and CP3N QuickStart

3-Series Control System® Automated Processors

Andere Handbücher für 3 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Crestron Computerhardware Handbücher

Crestron

Crestron DigitalMedia DMC-VID4 Bedienungsanleitung

Crestron

Crestron CNXENET+ Anleitung zur Verwendung

Crestron

Crestron C2IR-8 Anleitung zur Verwendung

Crestron

Crestron CNXMIDI Bedienungsanleitung

Crestron

Crestron C2N-IO Bedienungsanleitung

Crestron

Crestron DigitalMedia DMC-CPU3 Bedienungsanleitung

Crestron

Crestron DSP-860 Maßzeichnung

Crestron

Crestron UPX-OS4GB-MSO-2007 Bedienungsanleitung

Crestron

Crestron DIN-AP3 Original Betriebsanleitung

Crestron

Crestron CP4-R Bedienungsanleitung

Crestron

Crestron 4 Series Bedienungsanleitung

Crestron

Crestron DIN Rail Control Processor DIN-AP2 Anleitung zur Verwendung

Crestron

Crestron CNX-PAD8 Bedienungsanleitung

Crestron

Crestron TPS-GA-TPI Bedienungsanleitung

Crestron

Crestron ST-CP Bedienungsanleitung

Crestron

Crestron CP2 Bedienungsanleitung

Crestron

Crestron CNXCPU Anleitung zur Verwendung

Crestron

Crestron DIN-AP3MEX Original Betriebsanleitung

Crestron

Crestron C2VEQ-4 Bedienungsanleitung

Crestron

Crestron CNXCOM-2 Bedienungsanleitung

Crestron

Crestron UPX-2 Bedienungsanleitung

Crestron

Crestron DGE-100 Bedienungsanleitung

Crestron

Crestron UPX-2 Bedienungsanleitung

Crestron

Crestron 3 Series Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung