Crestron CNXMIDI Bedienungsanleitung

CRESTRON

Operations Guide - DOC. 8128 Contents •• i

Contents

CNX MIDI Interface Expansion Card: CNXMIDI 0

Description 0

Functional Description 0

Physical Description 0

Leading Specifications 0

Setup 0

Installation 0

Preparation for Use 0

Programming with SIMPL Windows 0

How the Program Works 0

How to Create the Program 0

Problem Solving 0

Troubleshooting 0

Further Inquiries 0

Return and Warranty Policies 0

Merchandise Returns / Repair Service 0

CRESTRON Limited Warranty 0

CRESTRON

Operations Guide - DOC. 8128 CNX MIDI Interface Expansion Card: CNXMIDI •• 1

CNX MIDI Interface Expansion

Card: CNXMIDI

Description

Functional Description

The CNXMIDI, a MIDI Interface Expansion Card provides MIDI IN, OUT, and

THRU interface. Use with devices such as mixers and lighting equipment.

Physical Description

The CNXMIDI, shown below, is a circuit board fastened to an aluminum faceplate.

The card is manufactured to easily fit into an unoccupied slot in a Crestron CNX

Generation Control System.

CNXMIDI Faceplate

5.000 in

(127.00 mm)

CNXMIDI MIDI INTERFACE

0.980 in

(24.89 mm)

THRU

OUT

The faceplate contains three female 5-pin DIN connectors. These are standard MIDI

connectors. Silk screening is applied to the faceplate; jacks are labeled THRU, IN,

and OUT from left to right, as shown above.

CRESTRON

2•• CNX MIDI Interface Expansion Card: CNXMIDI Operations Guide - DOC. 8128

Leading Specifications

The table below provides a summary of leading specifications for the CNXMIDI.

Dimensions and weight are approximations rounded to the nearest hundredth unit.

Leading Specifications of the CNXMIDI

DETAILS

Connectors (3) 5-pin DIN connectors

Power Requirements 24VDC, network power; 4 Watts

SIMPL™ Windows® Version 1.21.03 or later

CNX Operating System Version 5.01.29x or later

CNX Monitor Version 2.05x or later

Dimensions:

Height 0.98 in (24.9 mm)

Width 5.00 in (127 mm)

Depth 6.58 in (167.1 mm)

SPECIFICATIONS

As of the date of manufacture, the unit has been tested and found to comply with

specifications for CE marking.

Setup

Installation

Items required to install the CNXMIDI are already attached to the unit. The only

tools required are a Phillips tip screwdriver and a grounding strap. Follow the

assembly procedure below.

CAUTION: The CNXMIDI contains electrostatic sensitive devices (ESD); observe

precautions for handling ESDs to avoid damaging the card.

NOTE: If installing the CNXMIDI into a CNMSX-AV, it is assumed that the

CNXCAGE has been installed.

1. Disconnect power from the CNMSX.

2. Use the Phillips tip screwdriver and remove two screws and blank

faceplate from the control system.

3. Align the CNXMIDI with the card guides in the open slot and slide

the expansion card into position.

4. Firmly press both ends of the CNXMIDI faceplate to seat the

expansion card into the control system connector.

5. Tighten the thumb screws to secure the CNXMIDI to the control

system.

6. Reapply power to the CNMSX.

CRESTRON

Operations Guide - DOC. 8128 CNX MIDI Interface Expansion Card: CNXMIDI •• 3

Preparation for Use

The three female connectors on the CNXMIDI accept standard MIDI male cables.

Refer to the pinout table below if the connecting cable is to be made.

Standard MIDI 5-Pin Male DIN Pinout

MIDI IN

MIDI

OUT & MIDI THRU

ASSIGNMENT

1No Connection 1No Connection

2No Connection 2Ground

3No Connection 3No Connection

4Current Source 4Current Sink

5Current Sink 5Current Source

1 3

4 5

Programming with SIMPL Windows

SIMPL (Symbol Intensive Master Programming Language) is an easy-to-use

programming language that is completely integrated and compatible with all

Crestron system hardware. The objects that are used in SIMPL are called symbols.

SIMPL Windows offers drag and drop functionality in a familiar Windows®

environment.

SIMPL Windows is Crestron Electronics' software for programming Crestron

control systems. It provides a well-designed graphical environment with a number

of workspaces (i.e., windows) in which a programmer can select, configure,

program, test, and monitor a Crestron control system.

The next two subsections describe a sample SIMPL Windows program that utilizes

the CNXMIDI. The first subsection details how the sample program works with a

textual description and block diagram. The second subsection provides a broad

description of how to actually create the SIMPL Windows program.

NOTE: The following description assumes that the reader is familiar with SIMPL

Windows. If not, please refer to the extensive help information provided with the

software.

NOTE: There is no need to recreate the sample SIMPL Windows program. A copy

of this program is available from Crestron’s ControlCD (Version 5.1 or later).

Search for the CNXMIDI.SMW project in the SIMPL Windows Example Base.

CRESTRON

4•• CNX MIDI Interface Expansion Card: CNXMIDI Operations Guide - DOC. 8128

How the Program Works

A basic CNXMIDI SIMPL program is shown in block diagram form below. For this

example, the CNXMIDI occupies slot #1 of a CNMSX-PRO. This example plays

three notes on a MIDI keyboard. A note is turned on for 0.05s and then there is

silence for 0.05s before the next note is played. The sequence is triggered when a

certain note is received from the keyboard, and stopped at the end of the sequence.

Block Diagram of CNXMIDI

CRESTRON

Operations Guide - DOC. 8128 CNX MIDI Interface Expansion Card: CNXMIDI •• 5

How to Create the Program

Configuration Manager

Use the Configuration Manager workspace in SIMPL Windows to select and

configure all the devices that need to be included into the system. For this example,

add a CNXMIDI to slot #1 of the control system, shown below.

NOTE: SIMPL Windows v1.21.03 or later is required to program the CNMSX-AV

or PRO with a CNXMIDI card. If using an earlier version of SIMPL Windows,

Crestron recommends a SIMPL Windows and operation system upgrade. The latest

version can be obtained from the Software Downloads page of Crestron’s website

(www.crestron.com). New users are required to register in order to obtain access to

the FTP site.

Graphical System View of CNXMIDI in SIMPL Windows’ Configuration Manager

Programming Manager

Use the Programming Manager workspace in SIMPL Windows to select symbols

and assign their respective signals. Expand the Network Module folder and expand

the CNXMIDI. Double click on the ST-LT/MIDI serial driver to view it in detail

view (alternatively CTRL+D), as shown on the next page.

CRESTRON

6•• CNX MIDI Interface Expansion Card: CNXMIDI Operations Guide - DOC. 8128

Graphical Detail View of ST-LT/MIDI in SIMPL Windows’ Programming Manager

Expand the Logic folder to display the logic symbols used in this program. They

include Oscillator, Set Reset Latch, and Ring Counter symbols. Some logic symbols

are shown in optional sub system folders. Assign the signals as shown.

Graphical Detail View of Oscillator in SIMPL Windows’ Programming Manager

Graphical Detail View of Ring Counter in SIMPL Windows’ Programming Manager

Graphical Detail View of Set/Reset Latch in SIMPL Windows’ Programming Manager

Inhaltsverzeichnis

Andere Crestron Computerhardware Handbücher

Crestron

Crestron 3 Series Bedienungsanleitung

Crestron

Crestron ST-CP Bedienungsanleitung

Crestron

Crestron CNXENET+ Anleitung zur Verwendung

Crestron

Crestron CNX-PAD8 Bedienungsanleitung

Crestron

Crestron CNX-BIPAD8 Bedienungsanleitung

Crestron

Crestron CNXVTC-3 Bedienungsanleitung

Crestron

Crestron CP2 Bedienungsanleitung

Crestron

Crestron CNXAO-8 Bedienungsanleitung

Crestron

Crestron UPX-OS4GB-MSO-2007 Bedienungsanleitung

Crestron

Crestron UPX-2 Bedienungsanleitung

Crestron

Crestron CNXIO-16 Bedienungsanleitung

Crestron

Crestron CNX-PAD8A Bedienungsanleitung

Crestron

Crestron UPX-2 Bedienungsanleitung

Crestron

Crestron 4 Series Bedienungsanleitung

Crestron

Crestron DIN Rail Control Processor DIN-AP2 Anleitung zur Verwendung

Crestron

Crestron PC4-R Bedienungsanleitung

Crestron

Crestron DVPHD Bedienungsanleitung

Crestron

Crestron DIN-AP3 Original Betriebsanleitung

Crestron

Crestron CNXCOM-2 Bedienungsanleitung

Crestron

Crestron DIN-AP3MEX Original Betriebsanleitung

Crestron

Crestron UPX-2 Bedienungsanleitung

Crestron

Crestron C2VEQ-4 Anleitung zur Verwendung

Crestron

Crestron DigitalMedia DMC-VID4 Bedienungsanleitung

Crestron

Crestron DSP-860 Maßzeichnung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung