Crestron DM-NVX-E20-2G Bedienungsanleitung

The Crestron DM-NVX-E20-2G is a 2-gang wallplate network AV

encoder that transmits up to 4K60 4:2:0 video over standard Gigabit

Ethernet to a DM NVX® decoder. The DM-NVX-E20-2G provides HDMI®

and analog audio inputs and copper LAN connectivity with PoE (Power

over Ethernet) support.

The DM-NVX-E20-2G is available in two models: DM-NVX-E20-2G-B-T

(black textured) and DM-NVX-E20-2G-W-T (white textured).

In the Box

1 DM-NVX-E20-2G-B-T or DM-NVX-E20-2G-W-T

Additional Item

4 Screw, 6-32 x 1 inch, Truss Head, Combo (2054883)

Install the Device

The DM-NVX-E20-2G is designed for installation into a 2-gang electrical

box (not included) in a wall, floor, or ceiling. A minimum mounting depth

of 2 inches (51 mm) is required.

NOTE: Before installing the DM-NVX-E20-2G, verify that the

required wiring has been fed through the electrical box.

Connecting the Rear of the Device

Connect the rear of the device as required for the application.

NOTES:

lThe Ethernet port must be connected to a 1000BASE-T Ethernet

switch in order to stream network video.

lThe DM-NVX-E20-2G can be powered via the Ethernet port,

which is a PoE powered device (PD) port. In order for the device

to receive PoE, the Ethernet port must be connected to a PoE

power sourcing equipment (PSE) port of an Ethernet switch.

Wiring that is connected to a PoE PSE port is designed for

intrabuilding use only.

Alternatively, the DM-NVX-E20-2G can be powered by a 24 VDC

power pack (PW-2407WUL, sold separately).

Connections to Rear of DM-NVX-E20-2G

DM-NVX-E20-2G QuickStart

DM NVX® 4K60 4:2:0 Network AV Encoder, Wall Plate

Installing into an Electrical Box

To install the device into an electrical box (not included):

1. Using a Phillips screwdriver (not included), attach the DM-NVX-E20-

2G to the electrical box using the four included #6-32 x 1-inch combo

truss head screws.

2. Attach an FP-G2-DM Series decorator style faceplate (black FP-G2-

DM-B-T or white FP-G2-DM-W-T, sold separately) to the front of the

DM-NVX-E20-2G.

NOTE: An FP-G2-DM Series faceplate is required. Faceplates

other than the FP-G2-DM Series are incompatible with the DM-

NVX-E20-2G.

Installation into Electrical Box

DM-NVX-E20-2G QuickStart

DM NVX® 4K60 4:2:0 Network AV Encoder, Wall Plate

Connecting the Front of the Device

Connect the front of the device as required for the application. Upgrade the Firmware

Before using the device, upgrade the firmware. The latest firmware can

be downloaded from the DM-NVX-E20-2G-B-T or DM-NVX-E20-2G-W-

Tproduct page on the Crestron website (www.crestron.com).

Configure the Device

Configure the device using the web interface. To access the web

interface, open a web browser and then go to the IP address of the

device.

NOTE: By default, the IP address of a DM NVX device is assigned by

a DHCP server on the network. If a DHCP server does not exist on

the network, the IP address defaults to a link-local address in the

169.254.xxx.xxx range (refer to RFC 3927 for detailed information

about link-local addressing). To find the IP address of the DM NVX

device, use the Device Discovery tool in the Crestron Toolbox™

software.

If no account has been created, create an account by entering a user

name and password and confirming the password. After an account is

created, sign in to the web interface by entering the user name and

password.

DM-NVX-E20-2G QuickStart

DM NVX® 4K60 4:2:0 Network AV Encoder, Wall Plate

Connect to the Cloud

The XiOCloud®service allows supported devices across an enterprise to

be managed and configured from one central and secure location in the

cloud. Supported Crestron® devices are configured to connect to the

service out of the box.

Use of the service requires a registered XiOCloud account. To register

for an XiOCloud account, refer to

www.crestron.com/Support/Tools/Licensing-Registration/XiO-Cloud-

Registration-Room-Licenses.

1. Record the MAC address and serial number that are labeled on the

shipping box or the device. The MAC address and serial number are

required in order to add the device to the XiOCloud service.

NOTE:If the device has multiple MAC addresses, use the MAC

address that is providing the primary connection back to the

network. For most devices, the Ethernet MAC address should

be used. However, if your device is connecting to the network

over a different protocol (such as Wi-Fi® communications),

use the MAC address for that protocol instead.

2. Log in to your XiOCloud account at portal.crestron.io.

3. Claim the device to the XiOCloud service as described in the

XiOCloudUserGuide.

Select the device from the cloud interface to view its status and

settings. The device may now also be managed and assigned to a group

or room. For more information, refer to the XiOCloudUserGuide.

NOTE:For XiOCloud accounts with room-based licenses, the device

must be added to a licensed room before its status and settings can

be viewed.

Observe the LED Indicators

Refer to the following table for information about the LED indicators on

the device.

LED Indicator Color Meaning

PWR Amber Power is being applied to the

device. Thedevice is booting.

Green Power is being applied to the

device. Thedevice is

operational.

SETUP Red The SETUP button is pressed.

Ethernet Green An Ethernet link is

established.

Flashing amber Data activity is occurring on

the Ethernet link.

HDMI IN Green An HDMI signal is detected at

the HDMI input.

DM-NVX-E20-2G QuickStart

DM NVX® 4K60 4:2:0 Network AV Encoder, Wall Plate

Visit the Product Page

Scan the QR code to visit the product page.

DM-NVX-E20-2G-B-T

www.crestron.com/model/6511650

DM-NVX-E20-2G-W-T

www.crestron.com/model/6511651

Additional Information

Original Instructions

The U.S. English version of this document is the original instructions.

All other languages are a translation of the original instructions.

Regulatory Model: M202028005

Crestron product development software is licensed to Crestron dealers and Crestron

Service Providers (CSPs) under a limited nonexclusive, nontransferable Software

Development Tools License Agreement. Crestron product operating system software is

licensed to Crestron dealers, CSPs, and end-users under a separate End-User License

Agreement. Both of these Agreements can be found on the Crestron website at

www.crestron.com/legal/software_license_agreement.

The product warranty can be found at www.crestron.com/warranty.

The specific patents that cover Crestron products are listed at

www.crestron.com/legal/patents.

Certain Crestron products contain open source software. For specific information, visit

www.crestron.com/opensource.

Crestron, the Crestron logo, Crestron Toolbox, DM NVX, and XiO Cloud are either

trademarks or registered trademarks of Crestron Electronics, Inc. in the United States

and/or other countries. HDMI and the HDMI logo are either trademarks or registered

trademarks of HDMI Licensing LLC in the United States and/or other countries. Wi-Fi is

either a trademark or registered trademark of Wi-Fi Alliance in the United States and/or

other countries. Other trademarks, registered trademarks, and trade names may be used

in this document to refer to either the entities claiming the marks and names or their

products. Crestron disclaims any proprietary interest in the marks and names of others.

Crestron is not responsible for errors in typography or photography.

Doc. 9160A

03/13/23

DM-NVX-E20-2G QuickStart

DM NVX® 4K60 4:2:0 Network AV Encoder, Wall Plate

Inhaltsverzeichnis

Andere Crestron Medienkonverter Handbücher

Crestron

Crestron DM-NVX-352 Bedienungsanleitung

Crestron

Crestron DigitalMedia DM-NVX-350 Bedienungsanleitung

Crestron

Crestron DM-RMC-SCALER-C Bedienungsanleitung

Crestron

Crestron RCA Analog Video Input Card w/Analog Audio... Bedienungsanleitung

Crestron

Crestron DM-NVX-360 Bedienungsanleitung

Crestron

Crestron CNRJ11 Bedienungsanleitung

Crestron

Crestron DigitalMedia DM-NVX-350 Bedienungsanleitung

Crestron

Crestron DM-NVX-D80-IOAV Bedienungsanleitung

Crestron

Crestron DM-NVX-E20 Bedienungsanleitung

Crestron

Crestron DM-NVX-D30 Bedienungsanleitung

Crestron

Crestron DM-NVX-E760 Bedienungsanleitung

Crestron

Crestron DM-NVX-E30 Bedienungsanleitung

Crestron

Crestron HD-SCALER-HD-E Betriebsanleitung

Crestron

Crestron DigitalMedia DM-NVX-350 Maßzeichnung

Crestron

Crestron HD-SCALER Anleitung zur Verwendung

Crestron

Crestron DM-NVX-E20-2G-B-T Bedienungsanleitung

Crestron

Crestron HD-CONV-USB-300 Bedienungsanleitung

Crestron

Crestron DigitalMedia DM-NVX-351 Bedienungsanleitung

Crestron

Crestron DM-NVX-D80-IOAV Bedienungsanleitung

Crestron

Crestron DVPHD Bedienungsanleitung

Crestron

Crestron DM-NVX-D200 Bedienungsanleitung

Crestron

Crestron DM NVX Series Bedienungsanleitung

Crestron

Crestron HD-WP-4K-401-C Betriebsanleitung

Crestron

Crestron UC-BRKT-200-S-Z-ASSY Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung