Crestron CT-1000 Bedienungsanleitung

Crestron Series 1000

Wall-Mounted Touchpanel

Operations Guide

This document was prepared and written by the Technical Documentation department at:

Crestron Electronics, Inc.

15 Volvo Drive

Rockleigh, NJ 07647

1-888-CRESTRON

All brand names, product names and trademarks are the property of their respective owners.

Crestron CT-1000 & LC-1000 Touchpanels

Operations Guide – DOC. 5813B Contents •i

Contents

Series 1000 Wall-Mounted Touchpanels 1

Introduction ...............................................................................................................................1

Model Differences.......................................................................................................2

Specifications ..............................................................................................................2

Physical Description....................................................................................................3

Industry Compliance ...................................................................................................5

Setup ..........................................................................................................................................5

Network Wiring........................................................................................................... 5

Identity Code ............................................................................................................... 6

Configuring the Touchpanel........................................................................................6

Hardware Hookup ..................................................................................................... 10

Recommended Cleaning............................................................................................14

Programming Software............................................................................................................14

Programming with the Crestron AppBuilder............................................................. 15

Programming with SIMPL Windows ........................................................................ 15

Programming with VisionToolsPro-e..................................................................... 19

“Quick” Pushbuttons ................................................................................................. 23

Reserved Join Numbers............................................................................................. 23

Uploading and Upgrading........................................................................................................ 24

Communication Settings ...........................................................................................25

Uploading a SIMPL Windows Program.................................................................... 27

Uploading a VT Pro-e Project ................................................................................... 28

Firmware Upgrade..................................................................................................... 30

Problem Solving ...................................................................................................................... 32

Troubleshooting......................................................................................................... 32

Further Inquiries ........................................................................................................ 33

Future Updates .......................................................................................................... 33

Appendix: Early Production Units........................................................................................... 34

Software License Agreement................................................................................................... 37

Return and Warranty Policies .................................................................................................. 39

Merchandise Returns / Repair Service ...................................................................... 39

CRESTRON Limited Warranty.................................................................................39

Crestron CT-1000 & LC-1000 Touchpanels

Operations Guide – DOC. 5813B Series 1000 Wall-Mounted Touchpanels •1

Series 1000 Wall-Mounted

Touchpanels

Introduction

The Series 1000 compact wall-mounted touchpanels are 3.8-inch (9.7 cm) passive

matrix touchscreen control panels. There are two Series 1000 models available:

either grayscale or color. Model selection is based on application requirements. Refer

to “Model Differences” on page 2 for a more detailed description of each.

The purpose of a Series 1000 unit is to provide a single, compact touchpanel that

ends the age of walls cluttered with switches, control panels, thermostats, etc. These

wall-mounted panels can be fully customized for any control environment – graphic

icons and programmable “quick” pushbuttons let users easily select and control any

function.

Exclusive Crestrontechnology delivers added features: a crisp, clear, display that

automatically adjusts itself to changing lighting condition, dimming and brightening

as needed; storage and playback of WAV sound files adds a whole new dimension to

control; 10 “quick” pushbuttons flank the LCD display for frequently used

commands.

Functional Summary

* Custom-engraved keys can be obtained by using the Crestron Engraver software. Version 2.0.0.6 or later

is available from the Downloads | Software Updates section of the Crestron website (www.crestron.com).

•

Compact, stylish and affordable

• Touch sensitive 3.8-inch diagonal color or grayscale display

• 10 “quick” pushbuttons are ideal for frequently used commands

• Decorator-style faceplate is available with designer finishes and

custom-engraved keys*

• Exclusive Crestron “light-sensing” display adapts to any lighting

condition

• Supports color bitmap files and Windowsfonts

• Stores and plays back WAV sound files

• Easy drywall or back box mounting system

• Twisted pair, Cresnetor CAT5 wiring scheme allows daisy-chaining

of panels; never needs termination

Touchpanels Crestron CT-1000 & LC-1000

2 •Series 1000 Wall-Mounted Touchpanels Operations Guide – DOC. 5813B

Model Differences

There are two Series 1000 models available and selection depends whether grayscale

or color touchscreen is required. Grayscale panels are referred to as the LC-1000 and

color panels are known as CT-1000. Other differences between the two models are

listed in the table after this paragraph.

Series 1000 Touchpanel Model Differences

FEATURE LC-1000 CT-1000

Display Type Four Shades of Grayscale 4,096 Colors

Screen Illumination White LED Backlight Fluorescent Backlight

Power Requirements 3 W, 24 VDC, 125 mA 6 W, 24 VDC, 250 mA

Light Sensor Inversion and/or Backlight Dimming Backlight Dimming

Specifications

The table below and on the next page provides a summary of specifications for the

Series 1000 touchpanel.

Specifications for Series 1000 Touchpanel

SPECIFICATION DETAILS

Power Requirements 3 Watts (24 VDC @ 125 mA) - LC-1000 only

6 Watts (24 VDC @ 250 mA) - CT-1000 only

Default NET ID 3

Default Timeout 10 minutes

Signal Join Maximums 999 digital, 255 analog, 127 serial

Control System Update Files1,2,3

2-Series Control System Version C2-2004.CUZ or later

CEN/CN-TVAV Version 5.10.13V.UPZ or later

CNMSX-AV/PRO Version 5.07.05X.UPZ or later

CNRACKX/-DP Version 5.07.06W.UPZ or later

ST-CP Version 4.00.49S.UPZ or later

Acceptable File Extensions4

SIMPL Windows

.smw projectname .smw (source file)

.spz projectname .spz (compiled file for 2-Series)

.bin projectname .bin (compiled file for CNX generation)

.csz projectname .csz

(compiled file for CNX generation with SIMPL+)

VT Pro-e

.vtp projectname .vtp (source file)

.hex projectname .hex (compiled file)

Firmware

.csf FWxxxxxx.csf (panel firmware)

Audio Capacity Approximately 90 seconds of total time5

Audio Output 0.5 Watts

Memory 768 Kbyte flash memory

available for user project and WAV files6

Visible Touchscreen Dimensions 3.8" (9.6 cm) diagonal

Crestron CT-1000 & LC-1000 Touchpanels

Operations Guide – DOC. 5813B Series 1000 Wall-Mounted Touchpanels •3

Leading Specifications for Series 1000 Touchpanel (Continued)

SPECIFICATION DETAILS

Screen Viewing Angles:

LC-1000 Y Dir. (X=0o): +50o(from top), -30o(from bottom)

X Dir. (Y=10o): +40o(from right), -40o(from left)

CT-1000 Y Dir. (X=0o): +50o(from top), -50o(from bottom)

X Dir. (Y=0o): +50o(from right), -50o(from left)

Touchscreen Resolution 240 x 320 pixels

Touchscreen Display Passive Matrix Grayscale LCD (LC-1000 only)

Passive Matrix Color LCD (CT-1000 only)

Touchscreen Illumination White LED Backlit (LC-1000 only)

Backlit Fluorescent (CT-1000 only)

Touchscreen Composition Analog Resistive Membrane

Operating Temperature 50° to 113°F (10° to 45°C)

Humidity 10% to 90% RH (non-condensing)

Dimensions & Weight Height: 4.77 in (12.10 cm)

Width: 4.86 in (12.34 cm)

Depth: 1.59 in (4.04 cm) - with faceplate

Weight: 0.54 lb (0.25 kg)

1 The latest versions can be obtained from the Downloads | Software Updates section of the Crestron

website (www.crestron.com). Refer to NOTE after last footnote.

2 Crestron 2-Series control systems include the AV2, CP2, CP2E, MP2, MP2E, PAC2, PRO2, and

RACK2.

3 CNX update files are required for either CNMSX-AV/Pro or CNRACKX/-DP. Filenames for CNX

update files have a UPZ extension and ST-CP files are in one EXE or zipped UPZ file. To avoid

program problems, make certain you are using the update file with the correct suffix letter (e.g., S,

V, W, X).

4 Extension requires a prefix specific to the touchpanel type. In DETAILS, projectname represents the

assigned project name, and xxxxxx represents a version number.

5 The exact audio capacity is influenced by the complexity of the control screens and the sampling of

the WAV files. A specific WAV file format is required: PCM, 8KHz, mono, 8 bit.

6 Use VT Pro-e to check program size prior to upload to avoid storage capacity problems.

NOTE: Crestron software and any files on the website are for Authorized Crestron

dealers only. New users may be required to register to obtain access to certain areas

of the site (including the FTP site).

Physical Description

The 3.8-inch (9.7 cm) touch sensitive viewing screen is located on the front of the

Series 1000 touchpanel. The electronic hardware is housed in a high impact, molded

plastic enclosure, shown after this paragraph. A 4-pin network port is located at the

rear of the unit. A speaker is also located on the back of the unit to project sound

from the stored WAV audio files.

Touchpanels Crestron CT-1000 & LC-1000

4 •Series 1000 Wall-Mounted Touchpanels Operations Guide – DOC. 5813B

Series 1000 Touchpanel

Physical Views and Dimensions of a Series 1000 Touchpanel (CT-1000 Shown)

SIDE VIEWFRONT VIEW

4.765 in

(12.103 cm)

4.860 in

(12.344 cm)

REAR VIEW

1.365 in

(3.467 cm)

1.590 in

(4.039 cm)

ZAxxxxx

C000000

ELECTRONICS, INC.

ROCKLEIGH, NJ 07647

U.S.A.

CT-1000

4.145 in

(10.528 cm)

0.292 in

(0.742 cm)

TYP. 0.350 in

(0.889 cm)

TYP.

3.945 in

(10.020 cm)

4.043 in

(10.269 cm)

The Series 1000 touchpanel has 10 engravable hard buttons (real buttons, not

simulated hard buttons that press on the touchpanel membrane), that allow easy

access to the most common functions such as lights, volume, drapes, and screen

controls with the added benefits of touchpanel flexibility incorporated right into one

panel. Refer to the Engraving Software package, version 2.0.0.6 (available from the

Downloads | Software Updates section of the Crestron website (www.crestron.com).

A photosensor on the front panel permits the exclusive light-sensing display to

switch from daytime super bright to evening soft glow.

Crestron CT-1000 & LC-1000 Touchpanels

Operations Guide – DOC. 5813B Series 1000 Wall-Mounted Touchpanels •5

Industry Compliance

As of the date of manufacture, this unit has been tested and found to comply with

specifications for CE marking and standards per EMC and Radio Communications

Compliance Labeling (N11785).

NOTE: These devices comply with part 15 of the FCC rules. Operation is subject to

the following two conditions: (1) these devices may not cause harmful interference,

and (2) these devices must accept any interference received, including interference

that may cause undesired operation.

Setup

Network Wiring

NOTE: When installing network wiring, refer to the latest revision of the wiring

diagram(s) appropriate for your specific system configuration, available from the

Downloads | Product Manuals | Software and Wiring Diagrams section of the

Crestron website (www. crestron.com).

When calculating the wire gauge for a particular Cresnet run, the length of the run

and the power factor of each network unit to be connected must be taken into

consideration. If Cresnet units are to be daisy-chained on the run, the power factor of

each unit to be daisy-chained must be added together to determine the power factor

of the entire chain. The length of the run in feet and the power factor of the run

should be used in the following resistance equation to calculate the value on the right

side of the equation.

Resistance Equation

R = Resistance (refer to table below).

L = Length of run (or chain) in feet.

PF = Power factor of entire run (or chain).

R < L x PF

40,000 Where:

The required wire gauge should be chosen such that the resistance value is less than

the value calculated in the resistance equation. Refer to the table after this paragraph.

Wire Gauge Values

RESISTANCE (R) WIRE GAUGE

416

618

10 20

15 22

13 Doubled CAT5

8.7 Tripled CAT5

NOTE: All Cresnet wiring must consist of two twisted-pairs. One twisted pair is the

+24V conductor and the GND conductor and the other twisted pair is the Y

conductor and the Z conductor.

Touchpanels Crestron CT-1000 & LC-1000

6 •Series 1000 Wall-Mounted Touchpanels Operations Guide – DOC. 5813B

NOTE: When daisy-chaining Cresnet units, strip the ends of the wires carefully to

avoid nicking the conductors. Twist together the ends of the wires that share a pin on

the network connector, and tin the twisted connection. Apply solder only to the ends

of the twisted wires. Avoid tinning too far up the wires or the end becomes brittle.

Insert the tinned connection into the Cresnet connector and tighten the retaining

screw. Repeat the procedure for the other three conductors.

NOTE: For larger networks (i.e., greater than 28 network devices), it may be

necessary to add a Cresnet Hub/Repeater (CNXHUB) to maintain signal quality

throughout the network. Also, for networks with lengthy cable runs, it may be

desirable to add a hub/repeater after only 20 network devices.

Identity Code

Every equipment and user interface within the Cresnet system requires a unique

Cresnet identity code (NET ID). These codes are a two-digit hexadecimal number

from 03 to FE. Refer to “Interface Menu” on page 9 for instructions on setting the

unit's NET ID. The NET ID of the unit must match the NET ID specified in the

SIMPL Windows program. Refer to “Setting the Net ID in Device Settings” on page

17 for details of the SIMPL Windows procedure.

Configuring the Touchpanel

NOTE: The only connection required to configure the touchpanel is power. Refer to

“Hardware Hookup” on page 10 for details.

Main Menu

To configure the unit, it may be necessary to access a series of setup screens prior to

viewing run-time screens that are loaded into the touchpanel for normal operation.

The Main Menu for configuring the touchpanel appears when a finger is held

(approx. 5 seconds) to the touchscreen as power is applied. Remove your finger

when the message "SETUP MODE" appears on the touchscreen. Holding a finger to

the touchscreen for five seconds after the "SETUP MODE" message is displayed

sets the brightness to high and the contrast to a default level.

NOTE: “SETUP MODE” may also be entered by sending the respective command

from the Functions pull-down of the Crestron Viewport.

Upon entering SETUP MODE, the Main Menu, shown to the left, displays four

buttons: SAVE SETUP AND RUN PROGRAM, DIAGNOSTICS, TOUCH

SCREEN CALIBRATION, and SETUP.

The SAVE SETUP AND RUN PROGRAM button verifies that all of the setup

information has been saved to EEPROM and displays the main page that has been

programmed into your system. The remaining buttons on the Main Menu open other

menus, which are discussed in subsequent paragraphs.

Andere Handbücher für CT-1000

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Crestron Touchscreen Handbücher

Crestron

Crestron TST-602 Betriebsanleitung

Crestron

Crestron TPS-FPAR6000L Bedienungsanleitung

Crestron

Crestron Wallmount Touchpanel Bedienungsanleitung

Crestron

Crestron TS-1542 Betriebsanleitung

Crestron

Crestron 3200 Series Bedienungsanleitung

Crestron

Crestron Isys TPS-6000 Bedienungsanleitung

Crestron

Crestron TST-600 Bedienungsanleitung

Crestron

Crestron TSS-470E Bedienungsanleitung

Crestron

Crestron Isys TPS-3100L Bedienungsanleitung

Crestron

Crestron Isys TPS-6L Anleitung zur Verwendung

Crestron

Crestron TSW-570 Bedienungsanleitung

Crestron

Crestron TST-902 Bedienungsanleitung

Crestron

Crestron TPMC-9 Bedienungsanleitung

Crestron

Crestron TSS-770 Bedienungsanleitung

Crestron

Crestron MiniTouch MT-1000C Bedienungsanleitung

Crestron

Crestron MT-500C Bedienungsanleitung

Crestron

Crestron Isys TPS Series Bedienungsanleitung

Crestron

Crestron TPMC-3X Series Bedienungsanleitung

Crestron

Crestron TSW-570 Bedienungsanleitung

Crestron

Crestron ST-1700CIR Bedienungsanleitung

Crestron

Crestron TST-902 Maßzeichnung

Crestron

Crestron Isys TPS-4000L Bedienungsanleitung

Crestron

Crestron TSD-2220 Maßzeichnung

Crestron

Crestron Isys TPS-3000 Bedienungsanleitung

Beliebte Touchscreen Handbücher anderer Marken

FlowLine

FlowLine Data loop Bedienungsanleitung

ALPEX

ALPEX AEx-8 P Series Bedienungsanleitung

Ltech

Ltech E5S Bedienungsanleitung

Harman

Harman AMX MODERO S MSD-701-L2 Bedienungsanleitung

Acnodes

Acnodes PC 1150 Bedienungsanleitung

AIS

AIS IP10IA99 series Bedienungsanleitung

IBASE Technology

IBASE Technology ASTUT-152-RE1S Bedienungsanleitung

YASKAWA

YASKAWA TP 610C Bedienungsanleitung

B&R

B&R Power Panel C Series Bedienungsanleitung

Beijer Electronics

Beijer Electronics X2 control Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT321W-521 Bedienungsanleitung

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Bedienungsanleitung

Qomo

Qomo QIT1386 Bedienungsanleitung

DFI

DFI KS104-CD Bedienungsanleitung

AMX

AMX AXP-PPC Leitfaden

Sartorius

Sartorius X3 PR 5410 Bedienungsanleitung

AMX

AMX Modero X Series Bedienungsanleitung

Advantech

Advantech TPC-30 Series Bedienungsanleitung