Crestron TPS-4500IMW Bedienungsanleitung

Crestron TPS-4500IMW

Wall-Mounted Interface Module

Operations Guide

This document was prepared and written by the Technical Documentation department at:

Crestron Electronics, Inc.

15 Volvo Drive

Rockleigh, NJ 07647

1-888-CRESTRON

Crestron TPS-4500IMW Wall-Mounted Interface Module

Contents

Wall-Mounted Interface Module: TPS-4500IMW 1

Description.................................................................................................................................1

Functional Description ................................................................................................1

Physical Description....................................................................................................1

I/O Ports ......................................................................................................................1

Leading Specifications...............................................................................................................4

Setup ..........................................................................................................................................4

Network Wiring...........................................................................................................4

Hardware Hookup .......................................................................................................5

Problem Solving ........................................................................................................................9

Troubleshooting........................................................................................................... 9

Further Inquiries .......................................................................................................... 9

Future Updates ..........................................................................................................10

Return and Warranty Policies ..................................................................................................11

Merchandise Returns / Repair Service ...................................................................... 11

CRESTRON Limited Warranty.................................................................................11

Operations Guide - DOC. 5913 Contents •i

Crestron TPS-4500IMW Wall-Mounted Interface Module

Wall-Mounted Interface Module:

TPS-4500IMW

Description

Functional Description

The TPS-4500IMW is designed specifically to serve as an optional

interface module for the Crestron TPS-4500 tilt touchpanels. The module

provides a clean, 1-gang mountable interface for direct connection to the

touchpanel. The TPS-4500IMW creatively hides most of the connections

behind the wall. A visible RJ45 connector can be camouflaged with a

decora wallplate (not supplied) so that the unit blends into any setting.

Physical Description

The TPS-4500IMW, shown on the next page, is an option (can be

purchased separately). The unit mounts into a 1-gang electrical box

(recommended 2.5" depth). The back of the unit is silk-screened and

provides a network and video input connectors. Once installed, there is

only one RJ45 connector visible, which provides connection to the

touchpanel (cable, CA15859, supplied with touchpanel).

I/O Ports

There are four I/O ports available on the TPS-4500IMW. Details of each

are provided as bulleted items on page 3.

Operations Guide - DOC. 5913 Wall-Mounted Interface Module: TPS-4500IMW •1

Wall-Mounted Interface Module Crestron TPS-4500IMW

Physical Views of the TPS-4500IMW

(Front with Insert Plate, Side, and Back)

2.505 in

(6.363 cm)

CRESTRON

TPS-4500IMW

NET

75 Ohm

INPUT +

INPUT -

GROUND

1.485 in

(3.772 cm)

COMP

4.273 in

(10.853 cm)

Y24

2 •Wall-Mounted Interface Module: TPS-4500IMW Operations Guide - DOC. 5913

Crestron TPS-4500IMW Wall-Mounted Interface Module

• COMP Y and C – These two (four-pin) ports on the back of

the unit provide connection for a video source. The unit can

accept either a single signal over one wire (composite video or

COMP) or two separate signals: one for brightness (luminance

or Y), and the other for color (chrominance or C). The port is

made active with the purchase and installation of the TPS-VID,

composite and S-video input TV video card, into the

touchpanel. Consult the latest revision of the TPS-VID

Operations & Installation Guide (Doc. 5869) for details.

NOTE: Except for differential input (balanced) video signal, the two

(four-pin) video connectors with jumpers should be installed at all times.

Refer to "Hardware Hookup" on page 5 for jumper details.

• NET – This four-pin connector is used to connect to other

four-wire devices in the Cresnet system. If making network

connections to Cresnet peripherals, refer to "Network Wiring"

on page 4 for details.

• NET/VIDEO – This 10-position RJ45 mates with the

TPS-4500 touchpanel and has a dual purpose. Refer to the

descriptions and pinout table that follow this paragraph.

1. This port provides network and power connection to the

touchpanel.

2. This port also makes available composite or S-video input for

TV video card (with the purchase and installation of the

TPS-VID). Consult the latest revision of the TPS-VID

Operations & Installation Guide (Doc. 5869) for details.

NET/VIDEO Pinouts

PIN # DESIGNATION DESCRIPTION

1 +24V Power (Network)

2 GND Ground (Network)

3 C+ Chrominance (Positive)

4 C- Chrominance (Negative)

5 Y Data (Network)

6 Z Data (Network)

7 Y+ Luminance (Positive)/Composite

8 Y- Luminance (Negative)/Composite

9 GND Ground (Network)

10 +24V Power (Network)

Operations Guide - DOC. 5913 Wall-Mounted Interface Module: TPS-4500IMW •3

Wall-Mounted Interface Module Crestron TPS-4500IMW

Leading Specifications

The table below provides a summary of leading specifications for the

TPS-4500IMW. Dimensions and weight are rounded to the nearest

hundredth unit.

Leading Specifications for the TPS-4500IMW

SPECIFICATION DETAILS

Video Input Impedance 75 Ohms (with jumper)

100 Ohms (without jumper)

Dimensions Height: 4.27 in (10.85 cm)

Width: 2.51 in (6.36 cm)

Depth: 1.49 in (3.77 cm)

Weight 0.32 lb (0.14 kg)

As of the date of manufacture, the TPS-4500IMW has been tested and

found to comply with specifications for CE marking.

Setup

Network Wiring

NOTE: When making wire connections, refer to the latest revision of

the Cresnet Network Interconnect Drawing (Doc. 5411). The document

can be obtained from the Downloads page (CABLES and MANUAL

Libraries) of the Crestron website (www. crestron.com). Search for the

CRESNET.PDF files.

When calculating the wire gauge for a particular network run, the length

of the run and the power factor of each network unit to be connected

must be taken into consideration. If network units are to be daisy-chained

on the run, the load factor of each network unit to be daisy-chained must

be added together to determine the load factor of the entire chain. The

length of the run in feet and the load factor of the run should be used in

the following resistance equation to calculate the value on the right side

of the equation.

4 •Wall-Mounted Interface Module: TPS-4500IMW Operations Guide - DOC. 5913

Crestron TPS-4500IMW Wall-Mounted Interface Module

Resistance Equation

R = Resistance (refer to following table).

L = Length of run (or chain) in feet.

LF = Load factor of entire run (or chain).

R < L x LF

40,000 Where:

The required wire gauge should be chosen such that the resistance value

is less than the value calculated in the resistance equation. Refer to the

table after this paragraph.

Wire Gauge Values

RESISTANCE (R) WIRE GAUGE

416

618

10 20

15 22

13 24 (Doubled-CAT 5)

NOTE: All network wiring must consist of two twisted-pairs. One

twisted pair is the +24V conductor and the GND conductor and the other

twisted pair is the Y conductor and the Z conductor.

NOTE: When daisy chaining network units, always twist the ends of the

incoming wire and outgoing wire which share a pin on the network

connector. After twisting the ends, tin the twisted connection with solder.

Apply solder only to the ends of the twisted wires. Avoid tinning too far

up or the tinned end becomes brittle and breaks. After tinning the twisted

ends, insert the tinned connection into the network connector and tighten

the retaining screw. Repeat the procedure for the other three network

conductors.

Hardware Hookup

Connections to the Back of the TPS-4500IMW

The TPS-4500IMW serves as an optional interface between the

touchpanel and the Cresnet system. Refer to the illustration after this

paragraph for proper connections; apply power last. When making

network connections to the CNX Generation control system or Cresnet

peripherals, refer to "Network Wiring" on page 4 for details. It is not

necessary to make connections to a video source unless the TPS-VID has

Operations Guide - DOC. 5913 Wall-Mounted Interface Module: TPS-4500IMW •5

Wall-Mounted Interface Module Crestron TPS-4500IMW

been installed into the touchpanel and a video window object resides on a

page within the uploaded VisionTools™ Pro-e project.

Hardware Hookup Connections to the Back of the TPS-4500IMW

CRESTRON

TPS-4500IMW

CONNECT

TO CNX

GENERATION

CONTROL

SYSTEM

OR CRESNET

PERIPHERALS

CONNECT

TO VIDEO

SOURCE*

INPUT +

24 Y

NET

INPUT -

GROUND

COMP

75 Ohm

* CONNECTION TO A VIDEO SOURCE IS ONLY

NECESSARY IF THE TPS-VID EXPANSION

CARD IS INSTALLED INTO THE TOUCHPANEL.

POSSIBLE CONNECTION OPTIONS ARE:

- NO CONNECTION

- UNBALANCED VIDEO

(USING COAXIAL CABLE)

- BALANCED VIDEO

(USING TWISTED PAIR CABLE)

DEPENDING ON THE OPTION, THE TWO

JUMPERS ON THE NTSC/PAL VIDEO

FOUR-PIN CONNECTOR REMAIN

ATTACHED (AS SHOWN) OR ARE

REMOVED.

CONNECT

TO VIDEO

SOURCE*

NOTE: If there is no video source, do not make connections to either

NTSC/PAL video connector. However, leave connector and jumpers

attached to the NTSC/PAL video four-pin connector on the TPS-

4500IMW.

NOTE: Video balance is determined by external connections. Refer to

the two diagrams that follow this note.

Unbalanced Using Coaxial Cable

CONNECT TO

COMP Y FOR

COMPOSITE

VIDEO OR

LUMINANCE

COMPONENT

OF S-VIDEO.

CRESTRON

TPS-4500IMW

COMP

GROUND

INPUT +

INPUT -

75 Ohm

CONNECT

TO C FOR

CHROMINANCE

COMPONENT

OF S-VIDEO.

JUMPERS REMAIN

IN PLACE.

INPUT IMPEDANCE

EQUALS 75 OHMS.

6 •Wall-Mounted Interface Module: TPS-4500IMW Operations Guide - DOC. 5913

Inhaltsverzeichnis

Andere Crestron Touchscreen Handbücher

Crestron

Crestron C2N-FT-TPS4 Bedienungsanleitung

Crestron

Crestron TPMC-4XG Bedienungsanleitung

Crestron

Crestron STX-1600C Bedienungsanleitung

Crestron

Crestron Isys TPMC-4SM Original Betriebsanleitung

Crestron

Crestron CT-1600 Kurzanleitung

Crestron

Crestron CT-3000 Bedienungsanleitung

Crestron

Crestron TSW-70 Series Bedienungsanleitung

Crestron

Crestron TSW-732 Betriebsanleitung

Crestron

Crestron TS-70 Series Bedienungsanleitung

Crestron

Crestron TPMC-4SMD-FD Original Betriebsanleitung

Crestron

Crestron CT-1600 Anleitung zur Verwendung

Crestron

Crestron MTX-3 Bedienungsanleitung

Crestron

Crestron TSW-730 Bedienungsanleitung

Crestron

Crestron TSW-560 Betriebsanleitung

Crestron

Crestron STX-1550CW Bedienungsanleitung

Crestron

Crestron STX-1700C Bedienungsanleitung

Crestron

Crestron TSW-560 Betriebsanleitung

Crestron

Crestron FlipTop FT-TS600 Anleitung zur Verwendung

Crestron

Crestron TPS-1700 Bedienungsanleitung

Crestron

Crestron Isys TPS-12L Bedienungsanleitung

Crestron

Crestron TSW-570PR Series Bedienungsanleitung

Crestron

Crestron MT-500C Bedienungsanleitung

Crestron

Crestron STX-1550C Bedienungsanleitung

Crestron

Crestron TPMC-3X Series Bedienungsanleitung

Beliebte Touchscreen Handbücher anderer Marken

FlowLine

FlowLine Data loop Bedienungsanleitung

ALPEX

ALPEX AEx-8 P Series Bedienungsanleitung

Ltech

Ltech E5S Bedienungsanleitung

Harman

Harman AMX MODERO S MSD-701-L2 Bedienungsanleitung

Acnodes

Acnodes PC 1150 Bedienungsanleitung

AIS

AIS IP10IA99 series Bedienungsanleitung

IBASE Technology

IBASE Technology ASTUT-152-RE1S Bedienungsanleitung

YASKAWA

YASKAWA TP 610C Bedienungsanleitung

B&R

B&R Power Panel C Series Bedienungsanleitung

Beijer Electronics

Beijer Electronics X2 control Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT321W-521 Bedienungsanleitung

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Bedienungsanleitung

Qomo

Qomo QIT1386 Bedienungsanleitung

DFI

DFI KS104-CD Bedienungsanleitung

AMX

AMX AXP-PPC Leitfaden

Sartorius

Sartorius X3 PR 5410 Bedienungsanleitung

AMX

AMX Modero X Series Bedienungsanleitung

Advantech

Advantech TPC-30 Series Bedienungsanleitung