CrimeStopper CS-5601 Bedienungsanleitung

CS-5601

4 WINDOW CONTROL MODULE

INSTALLATION & OPERATING INSTRUCTIONS

INTRODUCTION:

CONGRATULATIONS on your choice of a 4 Window Control Module by Crimestopper Security Products Inc.

This booklet contains the information necessary for installing, and operating your system. If any questions

arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech Support number

below.

*IMPORTANT INFORMATION:

This system does not affect the operation of the factory power window switches. This is an ADD-ON

module to an Alarm, Remote Start, or Keyless Entry system. It is designed for medium to high current

window motors. It can roll 4 windows UP or DOWN, or 2 windows UP and DOWN. Each window circuit

activates in sequence, oneat a time. This minimizes the current draw on the vehicle battery.

This installation book is designed for the installer or individual with an existing understanding of automotive

electrical systems, along with the ability to test and connect wires for proper operation. To ease installation,

we suggest that you READ THIS MANUAL before beginning your installation. The information contained in

this manual is provided as a GENERAL GUIDLINE and it may differ from your vehicle! If you are not confident

with performing the installation steps as required by this system, we suggest seeking professional installation.

TECH SUPPORT

Mon-Fri 8:00 AM-4:30 PM Pacific Time

(800) 998-6880

REV -9/3/2004

TABLE OF CONTENTS

•Pre-Installation & Component Mounting………………..…….……………………………………………2-3

•Wiring …………..………………………………………………………………………………………….…….3-4

•4 Windows UP.…..………………………………………….……………….………..……………….…..……..5

•2 Windows UP and DOWN..………………….…………………………………………………………………6

•Vehicles with Normally Open Power windows……………..………….……………………………………7

•Testing and Adjusting Window Shut Off Current…………………..………………………………………8

PRE-INSTALLATION CONSIDERATIONS

To ease installation, we suggest that you READ THIS MANUAL before beginning your installation.

BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR

BAGS, ABS BRAKES, ENGINE / BODY COMPUTER AND BATTERY).

PLAN OUT YOUR INSTALLATION and determine most suitable locations for all components to be placed.

These components include: the module itself, valet/program button and possible relays. Allow enough wire to

create a service loop with strain relief, should servicing be required.

DAMAGE resulting from incorrect installation or failure to follow guidelines stated in this book will not be

covered under warranty and subject to repair or replacement charges.

USE A VOLT/OHM METER to test and locate all connections. Test Lights can damage a vehicle’s computer

systems.

ADDITIONAL PARTS, extra relays (Part #CS-402A) for converting normally open or normally powered

window switches to normally grounded.

DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED with brake, and gas pedals, steering

column, or any other moving parts in the vehicle.

REMOVE MAIN SYSTEM FUSE (S)before jump starting the vehicle or charging the vehicles battery.

COMPONENT MOUNTING

CONTROL MODULE: Locate the module under dash as high as possible, away from moving parts. Driver’s

Side usually provides an easy location for the majority of the wiring connections.

WARNING: Module isn’t water proof. Don’t Install CS-5601 Module inside vehicle door.

If the module gets water damaged, the vehicle windows could stop working.

WIRING

8Position Connector Plug –Small Wires

1 -GRAY: Negative roll trigger for Circuit #1 and #2.

Circuit #1and #2are controlled by LOOP 1-USE ONLY ONE.

2 -GRAY/WHITE: Positive roll trigger for Circuit #1 and #2.

3 -BLACK: SYSTEM CHASSIS GROUND:This wire must be connected to chassis metal of vehicle.

Scrape away any paint or dirt from the connection point to ensure a good connection.

4 -GREEN: (-) 300 milliamps Negative output though out operation of any 4 circuits

5 -YELLOW: (+) 300 milliamps Positive output through out operation of any 4 circuits

6 -BLUE: Negative roll trigger forCircuit #3 and #4.

Circuit #3and #4are controlled by LOOP 2 -USE ONLY ONE.

7 -BLUE/RED:Positive roll trigger for Circuit #3 and #4.

8 -PINK: Connect to an ignition wire that shows +12 Volts when the key in both “On” and “Start” positions.

This wire prevents the module from activating the windows while driving the vehicle.

WIRING

2 JUMPER LOOPS

LOOP 1: Circuit #1 and #2

•CUT:Constant or Latched (starter kill), Triggerfor window circuit #1 and #2.

•CONNECTED: Momentary Pulse (2nd channel), Trigger for window circuit #1 and #2.

LOOP 2:Circuit #3 and #4

•CUT:Constant or Latched (starter kill), Triggerfor window circuit #3 and #4.

•CONNECTED: Momentary Pulse (2nd channel), Trigger for window circuit #3 and #4.

9 Position Connector Plug –Large Wires

1 -RED WIRE: (+) 12 Volt Power Source (30 amp fuse) Connect to +12 Volt source with supplied fuse &

holder. Recommended location for this connection is at a main power distribution terminal or the vehicle

battery positive terminal.

2 -BLACK WIRE: (+) Switch side of window circuit #1. Normally Closed in reference to “BLACK” wire.

Circuit #1

3 -BLACK/WHITE WIRE: (+)12 volt output tomotor side of window circuit #1.

4 -GRAY WIRE: Switch side of window circuit #2. Normally Closed in reference to “GRAY/WIRE” wire.

Circuit #2

5 -GRAY/WHITE WIRE: (+)12 volt output tomotor side of window circuit #2.

6 -BROWN: Switch side of window circuit #3. Normally Closed in reference to “BROWN/WIRE” wire.

Circuit #3

7 -BROWN/WHITE: (+)12 volt output tomotor side of window circuit #3

8 -BLUE WIRE: Switch side of window circuit #4. Normally Closed in reference to “BLUE/WIRE” wire.

Circuit #4

9 -BLUE/WHITE WIRE: (+)12 volt output to motor side of window circuit #4

Left

Front

Circuit #1

Righ

t Front

Circuit #2

Left R

ear

Circuit #3

Right Rear

Circuit #4

Circuit #1 and #2 is used to roll widows up.

Circuit #3 and #4 is used to roll windows down.

rcuit #2

Circuit #1

Circuit #3

Circuit #4

This diagram is used on vehicles with window circuits that:

1. Switch ground to roll the windows up or down.

2. Switch both power and ground to roll the windows up or down.

3. Have a One Touch window switch to roll up or down or Express Down Toll Booth.

Circuit #1

**NOTE**

See page3

for 8 Pin

Plug Wiring

ADJSUSTING WINDOW SHUT OFF CURRENT

VR-2: WindowCircuit #3 and #4 VR-1: WindowCircuit #1 and #2

Turn clockwise to increase High Current shut off limit.

•Min = 10 Amps

•Max = 30 Amps

www.crimestopper.com

[email protected]

Phone (800) 998-6880

FAX (805) 581-9500

5601

Rear Access Door

ONLINE TECHNICAL SUPPORT

www.crimestopper.com/techweb03.html

Inhaltsverzeichnis

Andere CrimeStopper Autozubehör Handbücher

CrimeStopper

CrimeStopper PARK-PMCU Bedienungsanleitung

CrimeStopper

CrimeStopper CS-5101 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-870OEM Handbuch

CrimeStopper

CrimeStopper SV-9000 Bedienungsanleitung

CrimeStopper

CrimeStopper SecurView SV-6911.IR Bedienungsanleitung

CrimeStopper

CrimeStopper CA-504.BRKT Bedienungsanleitung

CrimeStopper

CrimeStopper SV-6930.LM.IR Bedienungsanleitung

CrimeStopper

CrimeStopper CS-9601PI Handbuch

CrimeStopper

CrimeStopper MIR-ACT Bedienungsanleitung

CrimeStopper

CrimeStopper CS-840RKE Bedienungsanleitung

CrimeStopper

CrimeStopper SV-5110 Bedienungsanleitung

CrimeStopper

CrimeStopper Electroplate EP-3000 Bedienungsanleitung

CrimeStopper

CrimeStopper CM-3000 Millenium FX Bedienungsanleitung

CrimeStopper

CrimeStopper MIR-045 Bedienungsanleitung

CrimeStopper

CrimeStopper ST-252.2 Bedienungsanleitung

CrimeStopper

CrimeStopper SecurView SV-6713 Bedienungsanleitung

CrimeStopper

CrimeStopper SecurView SV-9045 Bedienungsanleitung

CrimeStopper

CrimeStopper BSD-200 Bedienungsanleitung

CrimeStopper

CrimeStopper ST-604.4 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-845.RKE.II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-9602PI Kurzanleitung

CrimeStopper

CrimeStopper CS-5502 Bedienungsanleitung

CrimeStopper

CrimeStopper SV-6920.LM Bedienungsanleitung

CrimeStopper

CrimeStopper SV-9145 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung