CTC Union SDTU-01/ET10 Bedienungsanleitung

Revision: 2.1a

User's Manual

September 13, 2000

Revision Number:2.1a SDSL Modem

1. Overview........................................................ 1

2. Features......................................................... 1

3. Packaging....................................................... 1

4. Appearance.................................................... 2

5. Hardware Installation...................................... 3

6. Management................................................... 4

7. Default values................................................. 5

8. Software Upgrade........................................... 6

Appendix A. Console Setup..................................... 7

Appendix B. Command Line Interface...................... 8

Appendix C. Specifications.................................... 43

Hardware Specifications.................................... 43

Software Specifications..................................... 44

September 13, 2000

Revision Number:2.1a SDSL Modem

FIGURE 1 FRONT PANEL ......................................................... 2

FIGURE 2 REAR PANEL ........................................................... 2

FIGURE 3 HARDWARE INSTALLATION ........................................ 3

FIGURE 4: COMMAND TREE...................................................... 9

Manual

Revision Date Notes

V2.0 May 25, 2000 Software: V2.11B-H30.02-F45.108

lOriginal revision

V2.0a June 05,2000 Software:2.50B-H30.02-F45.111

V2.01 July 06, 2000 Software: 2.16R-H20.02-F45.111

V2.1 July 24, 2000 Software: 2.17R-H20.02-F45.111

V2.1a Sept. 13, 2000 Software: 2.15RX-H13.3002-F45.121

1. Overview

The SDTU-01/ET10 is an SDSL modem supporting ATM bridging

and routing, also 4 10BaseT Ethernet ports at the DTE side. The

SDSL front end provides symmetrical data rates from 144Kbps up to

2320Kbps with programmable rate at 8Kbps step. The SDTU-

01/ET10 can be configured to inter-operate with SDSL DSLAM or to

fit the Point-to-Point data transmission application by flexible CO/RT

configurations.

2. Features

üHigh Speed Symmetrical Data Transmission on Single Twisted

Copper Pair Wire

ü2B1Q Line Coding

üSymmetrical Multi-rate data transmission from 144Kbps up to

2320Kbps

üRFC 1483 Bridging over ATM over SDSL

üIPoA and PPPoA Routing over ATM over SDSL

ü4 x 10BaseT Ethernet Ports for PC/LAN

üHigh quality, simple operation, low power consumption

üCompatible and interoperable with major Central Office side SDSL

DSLAM or Multi-service Access System

üLocal OAM&P through command line interface via RS-232

Craft port

üLocal Telnet through the Ethernet interface

üRemote Telnet through SDSL interface

3. Packaging

This package consists of the following items:

4The SDTU-01/ET10 unit

4AC Adapter

4. Appearance

Front Panel

Figure 1: Front Panel

Rear Panel

Figure 2: Rear Panel

RJ11, SDSL inlet

RJ45*4, for connection to LAN or PC

Power Jack, for connection to an AC-DC power adapter, 12VDC, 1A

DB9, serial port for connection to ASCII data terminal

Green LED*4, On while corresponding Ethernet port is

connected. Blink while transmitting or receiving packets

Red LED, on when Ethernet

collision occur

WAN Status: Blinks while training with DSLAM and On

when SDSL link is ready

Power: On when the power supply is properly connected.

Activity: Blinks while transmitting or receiving packets over one of Ethernet

ports

LINK Status:On when one of Ethernet ports is properly connected to a

LAN or PC

Alarm:Blinks while booting up, and On when there is

an error, continuous “On” indicates internal error

5. Hardware Installation

1.Connect the SDSL cable, as (1) indicated in Figure 3, to the

LINE port of RJ-11 socket.

2.Use a RJ-45 cable, as (2) indicated in Figure 3, to connect

the SDTU-01/ET10 to the LAN or a PC with Ethernet adapter

installed.

Note: Be sure to use RJ45 crossover cable while

connecting to a hub.

3.Plug in the AC adapter to the AC power socket, then

connect the DC jack, as (3) indicated in Figure 3, to the DC

inlet of the SDTU-01/ET10.

4.Use a 9-pin RS232 cable as (4) indicated in Figure 3, to

connect the Console Port to a serial port of a terminal such

as PC with data terminal emulation software (Hyper

Terminal) installed, in order for local management.

Figure 3: Hardware Installations

(1)

(2)

)

(4)

SDSL outlet

Management Terminal

6. Management

SDTU-01/ET10 supports simple, flexible and easy-to-operate

methods for management purpose. The SDTU-01/ET10 can be

managed via the following paths, refer to Appendix B for

detailed information.

üConsole port – use the RS232 cable for connecting SDTU-

01/ET10 to an console terminal or an PC running terminal

emulation program, such as Hyper Terminal, see Appendix A

for proper console setup.

üLocal Ethernet Port – connect the Ethernet port to your local

area network or to a PC directly, “Telnet” SDTU-01/ET10 from

any workstation in the LAN. The default local Ethernet IP

address is “192.168.2.1”.

üSDSL port from remote site – while SDSL connection is in

service, you may remotely “Telnet” SDTU-01/ET10 from a

workstation networking to the CO equipment, the default

Remote Ethernet IP address is “192.168.1.1”.

Note: As operating SDSL modem requires technical know-how and

experience. It is recommended to manage SDTU-01/ET10 by

qualified technical staffs only. Therefore a password authentication

is applied when you enter the command line interface, consult your

service provider for obtaining the appropriate password.

7. Default values

SDTU-01/ET10 is pre-configured with the following parameters; user

may also re-load the default parameters by selecting Default from the

main menu.

LAN and VC setting WAN and SDSL

Ethernet (local) IP: 0.0.0.0 Side select: CPE (RT) side

Subnet mask: 0.0.0.0 Auto Rate: disable

Protocol: RFC1483, bridge Mode Rate select: 2320K

VPI/VCI: 8/35 Sign/Magnitude Bit Sequence:

normal

Class level (QoS): UBR Data Bit Polarity: Normal

PCR (Peak cell rate): 640 Scrambling: enable

Spanning tree: disable Idle-cell-sending: enable

Packet control: IP and PPPoE

DHCP setting:

Max-lease-time: 86400 seconds

8. Software Upgrade

You may easily upgrade the SDTU-01/ET10 embedded software

by obtaining the compressed upgrade kit from the service

provider then following the steps:

üExtract the ZIP file for updated firmware

üConnect SDTU-01/ET10 via the local Ethernet port or remote

SDSL link, make sure the SDTU-01/ET10 Ethernet IP address

and your terminal are properly configured so you can

successfully “ping” SDTU-01/ET10. The default local and remote

IP addresses are 192.168.2.1 and 192.168.1.1, respectively.

üUnder DOS prompt, execute command “xupgrade <IP

address of SDTU-01/ET10>”, for instance “xupgrade

192.168.1.1”.

üThis upgrading process might last as long as 60 seconds.

üThen reboot SDTU-01/ET10 with new software.

NOTE: Strictly maintain stable power to SDTU-01/ET10 while

upgrading software, if power failed during the upgrading

process, contents in the memory could be destroyed

and the system will hang. In such case you must call the

dealer or system integrator to repair.

Inhaltsverzeichnis

Andere CTC Union Netzwerk-Router Handbücher

CTC Union

CTC Union ICR-4103 Series Bedienungsanleitung

CTC Union

CTC Union ET100A Bedienungsanleitung

CTC Union

CTC Union Skywave Bedienungsanleitung

CTC Union

CTC Union ET100/NRZ Bedienungsanleitung

CTC Union

CTC Union MSW-4424C Series Bedienungsanleitung

CTC Union

CTC Union ICR-4103 Series Bedienungsanleitung

CTC Union

CTC Union atu-r130 Bedienungsanleitung

CTC Union

CTC Union ICR-W401 Bedienungsanleitung

CTC Union

CTC Union GSW-3420FM Bedienungsanleitung

CTC Union

CTC Union EOe-1 Bedienungsanleitung

CTC Union

CTC Union GSW-3208M Bedienungsanleitung

CTC Union

CTC Union VDTU2R140 Bedienungsanleitung

CTC Union

CTC Union GW-732FW Bedienungsanleitung

CTC Union

CTC Union FRM220-MSW404 Bedienungsanleitung

CTC Union

CTC Union FRM220A-1002ES Bedienungsanleitung

CTC Union

CTC Union FSW3208M Bedienungsanleitung

CTC Union

CTC Union SHDTU03-ET10R Bedienungsanleitung

CTC Union

CTC Union GW-632FW Bedienungsanleitung

CTC Union

CTC Union SHDSL Bedienungsanleitung

CTC Union

CTC Union ET100/G64 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung