Curtis Kubota M62 TLB Betriebsanleitung

1 of 37

INSTALLATION & OWNER’S MANUAL

Kubota M62 TLB Cab

p/n: 1KTLBM62

M62 Cab Shown

Available Options:

1. Rear Closeout Panel for Operation When Backhoe is Removed (P/N: 1KTLBM62RP)

2. Optional Rear Hydraulics Closeout panel for tractors with optional rear remote hydraulics installed (P/N: 1KTLBM62HYD)

3. Front or rear round LED Work Lights (fits both L47 and M62) (P/N: 1KTLBLEDWL) (not shown)

(*=Not including accessories)

Rev. E, 02/01/2018

p/n: IM-1KTLBM62

The contents of this envelope are the property of the owner. Leave with the owner when installation is complete.

Approximate Installation Time *

Experienced Dealer Technician – 6-8 Hours

Average Dealer Technician – 8-10 Hours

Do-It-Yourself – 10-14 Hours

Approximate Product Specifications

Fits Under the Factory Roof

Weight: M62: 586 lbs.

Cab Width: M62: 61-1/2” (3-1/2” wider than right fender)

2 of 37

TABLE OF CONTENTS

TABLE OF CONTENTS 2

INTRODUCTION 3

SAFETY INFORMATION 3-4

GENERAL INFORMATION 5

INSTALLATION 6-23

OPERATION 24-31

TROUBLESHOOTING 32

SERVICE PARTS BREAKDOWN 33-36

TORQUE CHART 37

3 of 37

INTRODUCTION

California Proposition 65

WARNING

Engine exhaust, some of its constituents,

certain vehicle components and fluids,

contain or emit chemicals known to the

State of California to cause cancer and birth

defects or other reproductive harm.

Curtis cabs feature an assembly of parts designed for your vehicle which require adjustment and

alignment of components to accommodate vehicle variations and provide proper weather protection.

For accurate installation, proper operation, and years of satisfaction, please read and understand the

installation and owner’s manual fully prior to installing the cab.

From all of us at Curtis, we thank you for choosing our product.

WARNING:

 Read and understand this entire manual and any other publications for the equipment being

operated.

 This cab enclosure adds additional weight to the base vehicle. Deduct the accessory’s total

weight (see front cover) from the vehicle’s rated capacity including operator. Never operate

the vehicle outside of its rated weight capacity.

 Use proper personal protective equipment during all phases of installation, removal and

operation.

 Ensure that the surrounding area is clear and that personnel are positioned away from the

area where engagement and disengagement of attachments will occur.

 Always shut off engine when leaving the operator’s area to perform any portion of the listed

procedures.

 Exposure to Carbon Monoxide can cause illness, serious injury or death.

Never operate vehicle if suspicious of Carbon Monoxide. Inspect exhaust system for leaks

monthly. Leaks can result from loose connections, corrosion, cracks or other damage to the

exhaust manifold. If leaks are found, repair or replace exhaust system. Do not use vehicle

until repair or replacement is complete.

Serious injury or death:

 This cab enclosure does not provide protection from rollover or other accidents.

 This cab enclosure does not provide protection from flying objects including golf balls.

 This cab enclosure does not provide protection from lightning. When lightning threatens,

take cover and do not operate vehicle.

SAFETY INFORMATION

4 of 37

IMPORTANT: Keep all decals clean and legible. Replace all missing, illegible, or damaged decals.

IMPORTANT: Decal placement locations shown are approximate; decals should not be placed in a location where

the operator’s field of view is impeded, and should not cover any portion of other decals installed in the same vi-

cinity.

INSTALLING OR REPLACING DECALS: Thoroughly clean the area where decal is to be placed using mild soap

and water. Allow the surface to fully dry. Remove the backing from the decal, exposing the adhesive surface. Ap-

ply the decal to the recommended position shown in the diagram below and smooth out any bubbles.

 1) WARNING: CRUSH POINT (9DL-196)

DECALS AND PLACEMENT

5 of 37

Check and tighten all hardware after 20 hours of operation. Periodically inspect and tighten hardware for

the remainder of the unit’s service life. Keep the enclosure components clean in order to prevent dust

and dirt from forming an unattractive film. The life of your cab components depend upon following these

care procedures:

1. NEVER USE AN ABRASIVE DETERGENT / VEHICLE CLEANER OR A WIRE BRISTLED BRUSH.

Do not use any CITRUS BASED CLEANERS such as orange or lemon.

2. Clean the enclosure surfaces thoroughly with warm soapy water and a COTTON cloth or chamois.

Be sure to use mild soap, specifically a dish liquid or equivalent. Clean in a light circular motion for

best results.

3. Remove grease and oil with mineral spirits and a COTTON cloth or chamois.

CARE & MAINTENANCE

All installation procedures listed within this manual are generally representative of the machine

model for which the manual is written. Your machine may be configured differently (e.g. SP1 vs. SP2,

etc.), but the outline for the procedure should still be followed. For further support for any issues not

covered within the pages of this manual, please contact Curtis Industries.

TOOLS REQUIRED:

Standard and Metric Wrenches

Standard and Metric Sockets

Torque Wrench

Allen Wrenches (T-Handle Recommended)

Razor Knife

Needle Nose Pliers

Grease

Measuring Tape

Silicone (black or clear)

Scissors

Snips

Electrical Tape

Drill

11/32” Drill Bit

Metal Cutting Saw (sawsall or cutoff wheel)

Teflon Tape

GENERAL INFORMATION

6 of 37

STEP 1: Vehicle Prep

1.1 Remove and save the Slow Moving Vehicle (SMV) sign

and bracket (see Figure 1.1).

1.2 Unplug and remove the round directionals from the rear

of the vehicle (see Figure 1.2).

1.3 Unplug and remove the optional work lights and brackets

(if installed) from the ROPS at the rear of the vehicle (see

Figure 1.3).

1.4 Remove and retain the front floor mat (see Figure 1.4).

Upon reinstallation at a later step, the floor mat will need

to be trimmed to fit around the cowl and several

alignment knobs will need to be removed.

1.5 Remove the rear backhoe floor panel from the hinge pins

and cut in line with the edge as shown in Figure 1.5. Use

a paint marker to cover the cut edge and re-install.

INSTALLATION

Figure 1.1: SMV Sign And Bracket

Figure 1.3: Remove Optional Rear Work Lights

Figure 1.4: Remove the Front Floor Mat

Front Floor Mat Figure 1.2: Remove Round Directionals

Figure 1.5: Trim Rear Floor Panel

Continue Edge

Through Panel

7 of 37

STEP 1: Vehicle Prep Cont.

1.6 Remove the battery cover and save for re-use.

1.7 Remove the hydraulics cover that is located on the

right side of the tractor beneath the floorboard and

set aside for re-use. This will make for easier

access to the floorboard fasteners.

INSTALLATION

Figure 1.6: Remove Battery Cover

Battery Cover

8 of 37

STEP 2: Cowl Assembly

2.1 Slide cowl over vehicle dash board (see Figure 2.1).

2.2 Fasten the bottom cowl flanges to the vehicle floor board

(see Figure 2.2). Repeat on opposite side. Leave bolts

loose.

Hardware Used QTY

5/16-18 x 3/4 Hex Head Flanged Cap Screw 2

5/16-18 Flanged Nylon Lock Nut 2

STEP 3: Windshield Support

3.1 Assemble the rear view mirror to the windshield support

(see Figure 3.1).

Hardware Used QTY

#10-32 x 1/2 Pan Head Machine Screw 2

#10-32 Flanged Nylon Lock Nut 2

3.2 Remove and retain the rear M12 nut, lock washer, and flat

washer from the upper front ROPS, just under the canopy

(see Figure 3.2, canopy hidden for clarity). Push the end of

the bolt flush with the OEM side frame bracket, but do not

remove. Repeat for the other side.

3.3 With assistance, place the windshield support against the

ROPS per Figure 3.2 and align the hole in the bracket on

each side to the M12 ROPS bolt. Push the bolt through the

bracket and secure with the flat washer, lock washer, and

M12 nut removed in step 3.2. Leave loose.

Figure 2.1: Slide On Cowl

Figure 2.2: Fasten Cowl to Floor Board

Figure 3.1: Assemble Mirror to Windshield Support Figure 3.2: Fasten Windshield Support

INSTALLATION

9 of 37

STEP 4: Rear Panel

Note: If installing this cab on a tractor with optional rear remote

hydraulics installed, Curtis kit 1KTLBM62HYD must be

installed. Refer to Step 1 in the installation manual for the kit

before installing the following rear panel otherwise there will be

an interference.

4.1 Remove and retain the outer most M12 nut, lock washer,

and flat washer from the upper front ROPS, just under the

canopy (see Figure 4.1). Push the end of the bolt flush

with the OEM side frame bracket, but do not remove.

Repeat for the other side.

4.2 With assistance, place the rear panel against the ROPS

per Figure 4.1 and push the M12 ROPS bolts through the

holes in the rear panel. Secure with the flat washer, lock

washer, and M12 nut removed in step 4.1. Leave loose.

4.3 Remove the bulb rubber trim on the right side of the rear

panel to expose the u-shaped slot.

4.4 Slice the supplied rubber grommet and install around the

vehicle wire harness

4.5 Install the grommet into the slot and re-install the bulb

rubber trim from step 4.3. The grommet will deform when

the rubber is re-installed.

STEP 5: Left Side Frame

5.1 Set a ROPS clamp in place on the left side ROPS tube

with the larger flange towards the front as shown in Figure

5.1.

5.2 Disconnect the gas shock at the top of the door and

remove the door with assistance by unlatching at the front

via the outer handle button or inside lever, and lift the door

off the hinge pins. Remove the rear window by opening the

latch, squeezing the buttons to release the latch and lifting

the window off the hinge pins.

CAUTION: Be wary of the brass washer at each hinge pin.

For best results, remove the washers and set them aside

until the windows and doors are re-installed later.

Figure 4.1: Fasten Rear Panel

INSTALLATION

Figure 4.3: Install Grommet on Harness

Grommet

Bulb Rubber

Figure 5.1: ROPS Clamp Set In Place

ROPS Clamp

10 of 37

Figure 5.3: Side Frame to W/S Support Bolts

3/4” Long Screws

Flanged Nuts

Figure 5.4: Upper Rear Mount

STEP 5: Left Side Frame Cont.

5.3 With assistance, set the left side frame up under the roof

and onto the floor board and fasten the side frame to the

windshield support (see Figure 5.3). Use the top hole on

the front part of the windshield support, as the lower hole

will be used with the windshield itself. Leave hardware

loose.

Hardware Used QTY

5/16-18 x 3/4 Hex Head Flanged Cap Screw 2

5/16-18 Flanged Nylon Lock Nut 2

5.4 Install left upper rear mount (see Figure 5.4.Frame and

rear panel are hidden). Leave hardware loose.

Hardware Used QTY

5/16-18 x 3/4 Hex Head Flanged Cap Screw 2

INSTALLATION

Inhaltsverzeichnis

Andere Curtis Landwirtschaftliche Geräte Handbücher

Curtis

Curtis Kubota L47 TLB Cab Betriebsanleitung

Beliebte Landwirtschaftliche Geräte Handbücher anderer Marken

GSi

GSi PNEG-2314 Bedienungsanleitung

Checchi & Magli

Checchi & Magli TEXDRIVE Bedienungsanleitung

Amazone

Amazone Cenius 4003-2TX Bedienungsanleitung

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Bedienungsanleitung

Cima

Cima BLITZ Bedienungs- und Wartungsanleitung

Amazone

Amazone CombiDisc 3000 Montageanleitung

HE-VA

HE-VA Disc-Roller XL Contour Bedienungsanleitung

AGT

AGT AGT-SSFM Bedienungsanleitung

Milestone

Milestone 72-84 Bedienungsanleitung

KUHN

KUHN Hector 3000 Bedienungsanleitung

Krone

Krone X-Disc 6200 Bedienungsanleitung

Eliet

Eliet DZC450 Bedienungsanleitung

Taarup

Taarup BIO+ B4000 Bedienungsanleitung

Garland

Garland SHAKER 310 DPG Bedienungsanleitung

stable comfort

stable comfort StableWall System Bedienungsanleitung

Raven

Raven AccuBoom Bedienungsanleitung

International

International 710 Bedienungsanleitung

Ashland

Ashland HDW-3217-14 Bedienungsanleitung