CyberData VoIP V2 Bedienungsanleitung

Quick Start Guide 930459D

The IP Endpoint Company

1.0 Out-of-Box and Prior to Final Installation

1.1. Verify that you have received all of the parts listed on the Installation Quick

Reference placemat.

1.2. Download the current manual, otherwise known as an Operation Guide,

which is available on the Documentation page at the following website

address:

http://www.cyberdata.net/products/voip/digitalanalog/loudspeakerampv2/docs.html

Note You can also navigate to the Documentation page by going to

www.CyberData.net and following the steps that are indicated by

the following figures:

2.0 Select Power Source

Note For PoE powered, place DIP Switches 1and 4to OFF and place DIP Switch 3

to ON.

PoE Switch PoE Injector

Set PoE power type to Class 0 = 13W

CAT6 cable recommended—

for longer distances

Be sure you are using a non-PoE switch or port

Make sure port is not in trunk mode

Set port to full duplex/ 100mbps

Spanning Tree Protocol (STP) must be disabled or Portfast enabled

VoIP V2 Loudspeaker Amplifier

Quick Start Guide (AC-Powered)

Quick Start Guide 930459D

3.0 Power Test

3.1. Plug in the CyberData device and monitor the LED activity on the front of

the device. See the following figure:

3.2. The GREEN power and status LEDs and the YELLOW link LED come on

immediately. The activity LED illuminates GREEN for a 10Mb link or

YELLOW/GREEN for a 100MB when the network link to the Paging

Amplifier is established. The activity LED blinks to indicate network traffic.

After about 27 seconds, the GREEN status LED will blink twice to indicate

that the amplifier is fully booted.

If there is no DHCP server available on the network, it will try 12 times with a

three second delay between tries and eventually fall back to the

programmed static IP address (by default 10.10.10.10). This process will

take approximately 80 seconds.

3.3. When the device has completed the initialization process, press and hold

the RTFM switch for 3 seconds to announce the IP address.

This concludes the power test. Go to Section 4.0, "Connecting to a Network

in a Test Environment".

Activity LED (GREEN)

Link LED (GREEN/YELLOW)

Quick Start Guide 930459D

4.0 Connecting to a Network in a Test Environment

Note The following connections are usually needed for this procedure:

• Computer

• PoE switch or injector

• CyberData device

4.1. In a test environment, use a computer that is connected to the same switch

as a single CyberData device. Note the subnet of the test computer.

4.2. Use the CyberData Discovery Utility program to locate the device on the

network. You can download the Discovery Utility program from the following

website address:

http://www.cyberdata.net/support/voip/discovery.html

4.3. Wait for initialization to complete before using the Discovery Utility program

to scan for a device. The device will show the current IP address, MAC

address, and serial number.

4.4. Select the device.

4.5. Click Launch Browser. If the IP address is in a reachable subnet from the

computer that you are using to access the device, the Discovery Utility

program should be able to launch a browser window pointing to the device’s

IP address.

4.6. Log on to the web interface by using the default username (admin) and

password (admin) to configure the device.

4.7. Perform an audio test by pressing the Test Audio button that is located at

the bottom of the Device Configuration page. If the audio test message is

clearly audible, then your CyberData device is functioning properly.

4.8. The device is now ready to be set for your desired network configuration.

You may search the Compatible IP-PBX Servers index for available

sample VoIP phone system configurations and set up guides at the following

website address:

http://www.cyberdata.net/support/server/index.html

Quick Start Guide 930459D

5.0 Contacting CyberData VoIP Technical Support

Please visit our website and complete the Contact VoIP Tech Support form

available at the following website address:

http://www.cyberdata.net/support/contactsupportvoip.php

Note You can also navigate through menus to the Support form by going to

www.CyberData.net as shown in the following figure:

The Contact VoIP Tech Support form initiates a ticket which CyberData uses for

tracking. Most importantly, the Contact VoIP Tech Support form tells us which

PBX system and software version that you are using, the make and model of the

switch, and other essential troubleshooting information. Please also include as

much detail as possible in the Describe Problem section of the Support form.

Requests for Returned Materials Authorization (RMA) numbers require an active

VoIP Technical Support ticket number. A product will not be accepted for return

without an approved RMA number.

More information about warranty and RMA returns is available at the following

website address:

http://www.cyberdata.net/support/warranty/index.html

Andere Handbücher für VoIP V2

Inhaltsverzeichnis

Andere CyberData Verstärker Handbücher

CyberData

CyberData 11097 Bedienungsanleitung

CyberData

CyberData 010861 930106A Bedienungsanleitung

CyberData

CyberData 11097 Bedienungsanleitung

CyberData

CyberData Amplifier Bedienungsanleitung

CyberData

CyberData VoIP V2 Bedienungsanleitung

CyberData

CyberData 11096 Bedienungsanleitung

CyberData

CyberData 011579 Bedienungsanleitung

CyberData

CyberData InformaCast Enabled 011407 Bedienungsanleitung

CyberData

CyberData 11095 Bedienungsanleitung

CyberData

CyberData 10860 Bedienungsanleitung

CyberData

CyberData 011403 Bedienungsanleitung

CyberData

CyberData 011405 Handbuch

CyberData

CyberData 011403 Bedienungsanleitung

CyberData

CyberData 11095 Handbuch

CyberData

CyberData 011405 Bedienungsanleitung

CyberData

CyberData 011404 Bedienungsanleitung

CyberData

CyberData 011579 Bedienungsanleitung

CyberData

CyberData VoIP Loudspeaker Amplifier Part #010859 Bedienungsanleitung

CyberData

CyberData 011404 Handbuch

CyberData

CyberData Part #010861 Bedienungsanleitung

CyberData

CyberData 11061 Bedienungsanleitung

CyberData

CyberData 011403 Handbuch

CyberData

CyberData InformaCast Enabled 011406 Bedienungsanleitung

CyberData

CyberData 011085 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung