CYP PU-515PL-TX Bedienungsanleitung
PU-515PL-TX & RX
HDBaseT™ LITE Extender Set with PoE & 2-way IR
OPERATION MANUAL
3
DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. CYP (UK) Ltd assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be
contained in this document. CYP (UK) Ltd also makes no commitment to
update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer le, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express
written permission and consent from CYP (UK) Ltd.
© Copyright 2019 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated
4
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if
it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sucient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE SUMMARY OF CHANGE
v1.01 25/10/2013 First release
v1.02 22/08/2019 Updates to Specications
5
CONTENTS
1. Introduction...........................................6
2. Applications ...........................................6
3. Package Contents ..................................6
4. System Requirements ...........................6
5. Features..................................................7
6. Operation Controls and Functions .......8
6.1 Transmitter Front and Rear Panels....... 8
6.2 Receiver Front and Rear Panels ............ 9
6.3 D-Sub 9-Pin Denitions.........................10
6.4 IR Cable Pin Assignment .......................10
7. Connection Diagram .......................... 11
8. Specications...................................... 12
8.1 Technical Specication ..........................12
8.2 CAT5e/6/7 Cable Specication ...........13
9. Acronyms............................................. 14
6
1. INTRODUCTION
The HDBaseTTM HDMI over single CAT5e/6 with bi-directional IR, RS-232
& PoC Transmitter and Receiver set can make your home or oce set-up
more ecient and easy to use. Uncompressed video and audio can be
transmitted up to 70 metres at 1080p or 40 metres at 4K. with the PoC
function and added benet of controls through the built-in RS-232 and
IR ports. This family design of HDBaseT technology allows a full usage of
HDMI and controls over CAT5e/6/7.
2. APPLICATIONS
Domestic HDMI installations
University lecturing systems
Retail showroom systems
Conference presentation and control
3. PACKAGE CONTENTS
Transmitter Package
1×HDMI over Single CAT5e/6/7 Transmitter with PoC
1×IR Blaster
1×3.5 mm Mini-jack to RS-232 Female Cable
24 V/1.25 A DC Power Adaptor
Operation Manual
Receiver Package
1×HDMI over Single CAT5e/6/7 Receiver with PoC
1×IR Extender
1×3.5 mm Mini-jack to RS-232 Male Cable
Operation Manual
4. SYSTEM REQUIREMENTS
HDMI source equipment such as a DVD or Blu-ray player and HDMI
equipped display (TV or monitor). HDMI and CAT5e/5/7 connection
cables.
7
5. FEATURES
HDMI 1.x and DVI 1.0 compliant
HDCP compliant
Supports HDMI 3D and 4K x 2K features
Supports HDCP repeater and CEC bypass
Supports distance up to 70m/229ft at 1080p and 40m/131ft at 4K
through CAT5e/6/7 cable
HDMI input resolutions up to 4K@60Hz (YUV 4:2:0, 8-bit) or 4K@30Hz(
YUV 4:4:4, 8-bit)
Supports pass-through of audio formats including LPCM 2.0/5.1/7.1,
and Bitstream over HDMI
Supports HDBaseT Lite Technology
Installation friendly
Note
1. This system was tested with CAT-6E/23AWG cables, results may vary with
cables of a dierent specication.
2. The PoC function is designed for powering compatible receiver units
only—do not use with non-PoC receivers or receivers of another brand.
8
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Transmitter Front and Rear Panels
Power
Link
CAT 5e /6/7 Out
IR2 Extender
RS-232 In IR1 Blaster
HDMI In
Transmitter
1 2 3 4 5 6 7 8
1
RS232 In: Connect to a PC/laptop or RS-232 control device (with
supplied 3.5 mm mini-jack to D-sub 9-pin adaptor) for the transmission
of RS-232 commands.
2
IR2 Extender: Connect an IR extender cable for IR signal reception.
Ensure that remote control being used is within the direct line-of-
sight of the IR extender.
3
IR1 Blaster: Connect an IR blaster cable for IR signal transmission.
Place the IR blaster in direct line-of-sight of the equipment to be
controlled.
4
HDMI In: Connect to the HDMI source equipment such as a DVD or
Blu-ray player.
5
DC 24V: Connect the 24V DC power supply to the unit and plug the
adaptor into an AC outlet.
6
Link LED: The yellow LED will illuminate when both the input and
output CAT5e/6/7 signals are connected. The LED will blink when
there is an error with the transmission signal.
7
Power LED: This green LED will illuminate when the device is
connected to a power supply.
8
CAT5e/6 Out: Connect to the receiver unit with a single CAT5e/6/7
cable for transmission of all data signals.
9
6.2 Receiver Front and Rear Panels
Power
Link
CAT 5e /6/7 In
IR1 Extender
RS-232 Out IR2 Blaster
HDMI Out
Receiver
2 3 4 5 6 71
1
Power LED: This green LED will illuminate when the device is
connected to a power supply.
2
Link LED: This yellow LED will illuminate when both the input and
output CAT5e/6/7 signals are connected. The LED will blink when
there is an error with the transmission signal.
3
CAT5e/6 In: Connect to the transmitter unit with a Single CAT5e/6/7
cable for transmission of all data signals.
4
RS232 Out: Connect to the device that is to be controlled (with
the supplied 3.5mm mini-jack to D-sub 9-pin adaptor) by RS-232
commands
5
IR1 Extender: Connect an IR extender cable for IR signal reception.
Ensure that the remote being used is within the direct line-of-sight of
the IR extender.
6
IR2 Blaster: Connect an IR blaster cable for IR signal transmission.
Place the IR blaster in direct line of sight of the equipment to be
controlled.
7
HDMI Out: Connect to a HDMI equipped TV/monitor for display of the
HDMI input source signal.
10
6.3 D-Sub 9-Pin Denitions
PIN DEFINE TX/RX
1N/C
2TxD/RxD
3RxD/TxD
4N/C
5GND
6N/C
7N/C
8N/C
9N/C
6.4 IR Cable Pin Assignment
3
1
3
2
2
1Power 5V
IR Blaster Signal
NC
IR Signal
Power 5V
Ground
IR Extender
IR Blaster
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere CYP Extender Handbücher
CYP
CYP CH-506TX Bedienungsanleitung
CYP
CYP PUV-2000TX Bedienungsanleitung
CYP
CYP PU-514L-KIT Bedienungsanleitung
CYP
CYP PRO-3GSDIHDMI Bedienungsanleitung
CYP
CYP CH-513TXL Bedienungsanleitung
CYP
CYP PU-1106-KIT Bedienungsanleitung
CYP
CYP CH-110TX Bedienungsanleitung
CYP
CYP SDV-FTX Bedienungsanleitung
CYP
CYP CPLUS-VHHE Bedienungsanleitung
CYP
CYP PUV-2010TX Bedienungsanleitung
CYP
CYP CH-506TXPL Bedienungsanleitung
CYP
CYP PUV-1510RX Bedienungsanleitung
CYP
CYP CETH-4USB Bedienungsanleitung
CYP
CYP IP-6000TXRX Bedienungsanleitung
CYP
CYP PU-1107-KIT Bedienungsanleitung
CYP
CYP PU-513L-KIT Bedienungsanleitung
CYP
CYP PUV-1230PL-RX Bedienungsanleitung
CYP
CYP CH-514RXL Bedienungsanleitung
CYP
CYP PU-USB-KIT Bedienungsanleitung
CYP
CYP PU-506-KIT Bedienungsanleitung
