CYP PUV-2000TX Bedienungsanleitung
CH-1602TXR & CH-1602RXR
HDMI/Audio over CAT5e/6/7 Extender with 48V PoE
Operation Manual
Operation Manual
PUV-2000TX & PUV-2000RX
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of fi re,
electrical shock and injury to persons.
• To prevent fi re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
suffi cient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE (DD/MM/YY) SUMMARY OF CHANGE
VR0 21/08/15 Preliminary Release
CONTENTS
1. Introduction............................................ 1
2. Applications........................................... 1
3. Package Contents ................................ 1
4. System Requirements............................ 2
5. Features.................................................. 2
6. Operation Controls and Functions....... 3
6.1 Transmitter Front Panel ....................3
6.2 Transmitter Left and Right Panels ...4
6.3 Receiver Front Panel........................5
6.4 Receiver Left and Right Panels.......6
6.5 IR Cable Pin Assignments ................7
7. Connection Diagram ............................ 8
8. Specifi cations ........................................ 9
8.1 Technical Specifi cation...................9
8.2 CAT5e/6/7 Cable Specifi cation ...10
9. Acronyms ............................................. 10
1
1
1. INTRODUCTION
This HDMI and Audio over Single CAT5e/6/7 Transmitter and Receiver
set can send uncompressed audio/video along with controls and IP
over a single run of CAT5e/6/7 cable up to 100m. It has the added
benefi t of control through the built-in RS-232 and IR ports. With LAN
serving connection and external digital and analog audio capability
that gives users the convenience of additional audio connection. The
48V PoE design can power the Receiver (PD) from the Transmitter (PSE),
eliminating the need for a separate power supply for the Receiver.
Also, the ultra-thin mechanical designs allow fl exibility mounting
position saving more space and make presentation orderly and tidy.
2. APPLICATIONS
• 48V PoE from Transmitter (PSE) to Receiver (PD)
• Household entertainment extending and control
• Lecture room display and control
• Showroom display and control
• Meeting room presentation and control
• Classroom display and control
3. PACKAGE CONTENTS
• 1×HDMI/Audio over CAT5e/6/7 Transmitter
• 1×HDMI/Audio over CAT5e/6/7 Receiver
• 1×IR Blaster
• 1×IR Extender
• 1×48 V/0.83 A DC Power Adaptor
• 1×Power Cable
• 2×Rack Ears Sets
• 1×Operation Manual
2
2
4. SYSTEM REQUIREMENTS
Input source equipment such as DVD/Blu-ray player, host PC/Laptop
and HDMI equipped output display (TV or monitor) with amplifi er or
active speakers.
5. FEATURES
• Supports HDBaseT 2.0 specifi cation supporting over a single CAT6/7
cable up to 100m/328ft and CAT5e cable up to 90m/295ft
• HDMI (with 3D & 4K2K 60_YUV420 support), HDCP 2.2 and DVI
compatible
• HDBaseT 5Play™ convergence: High-Defi nition (HD) Video and
Audio, 100BaseT Ethernet, PoE and Control (Bidirectional IR/RS-232
pass-through)
• Supports pass-through of HD audio formats: LPCM 2/5.1/7.1CH,
Dolby Digital 2/5.1CH, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos
and DTS-HD Master Audio
• Supports optical sampling rate up to 48kHz
• Supports Ethernet network connection
• Supports external analog and digital audio transmission
• Supports RS-232 baud rate from 110~115200bps
3
3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Transmitter Front Panel
DC 48V POWER AUDIO IN IR IN2IR OUT1 UPDATERS-232 IN
TX RX
+−
LR
CAT5e/6/7 OUT
HDMI IN
OPT.
OUTLAN
ARC OUT
OFF ON
1 2 3 4 5 6
1
DC 48V and POWER LED: Plug the 48V DC power supply into the
unit and connect the adaptor to an AC outlet and the LED will
illuminate.
2
AUDIO IN L/R: Connect with audio source equipment such as PC
or CD player for audio signal sending to Receiver’s AUDIO OUT L/R.
3
IR IN 2: Connect to the supplied IR Extender cable for IR signal
reception. Ensure that remote being used is within the direct line-
of-sight of the IR Extender.
4
IR OUT 1: Connect to the supplied IR Blaster Cable for IR signal
transmission. Place the IR Blaster in direct line-of-sight of the
equipment to be controlled.
5
RS-232 IN TX/RX: Connect to a PC or Laptop with 3-pin Relay cable
for the transmission of RS-232 commands. For receiving command
from Receiver side, the TX and Rx pin must be reversed.
6
UPDATE: This is reserved for fi rmware update use only. Switch
this deep switch to left for fi rmware update use, under normal
operation, leave the switch on right. Update procedure may be
done from the same RS-232 port for both Transmitter and Receiver.
4
4
6.2 Transmitter Left and Right Panels
HDMI IN
OPT.
OUTLAN
ARC OUT
OFF ON
CAT5e/6/7 OUT
12 3 4 5
Left Right
1
CAT5e/6/7 OUT: Connect to the Receiver unit with a single
CAT5e/6/7 cable for transmission of all data signals. Under proper
connection the green LED will illuminate to indicate PoE activated.
The yellow LED will illuminate to indicate successful connection
between Transmitter and Receiver, when it blink irregularly it
represent the link error or when not illuminate it means no link with
Receiver.
2
LAN: Connect to an internet or network connection. The yellow LED
will illuminate to represent the link with Receiver is steady, when
it blink irregularly it represent the link error or when not illuminate
it means no link with Receiver. The green LED will illuminate to
represent the Ethernet speed is with 100Mbit/s.
3
OPT. OUT: Connect to speaker for audio signal output from
Receiver’s OPTICAL IN.
4
ARC OUT OFF/ON SWITCH: Switch this dip switch to allows ARC
(Audio Return Channel) function to be activate or not. Switch to
OFF to disable ARC function. Switch to ON allows Receiver’s HDMI
output audio to be routed back and output to both HDMI IN and
Optical OUT on the Transmitter side.
Note: When ARC switch to ON, depending on the connected
devices of the HDMI OUT & Optical in, the ARC input/output
transmission distance may be varied. It is suggested to use cable
within 2 meters long to ensure the best audio quality.
5
HDMI IN: Connect to HDMI source equipment such as a DVD or
Blu-ray player.
5
5
6.3 Receiver Front Panel
OPT.
IN
POWER AUDIO OUTIR IN1IR OUT2 UPDATERS-232 OUT
TX RXLR
CAT5e/6/7 IN
HDMI OUTLAN
OPT.
IN
ARC
IN
1 2 3 4 5 6
1
POWER LED: This LED will illuminate when device is connected with
power supply.
2
AUDIO OUT L/R: Connect to speaker with RCA input for audio
signal output.
3
IR IN 1: Connect to the supplied IR Extender cable for IR signal
reception. Ensure that remote being used is within the direct line-
of-sight of the IR Extender.
4
IR OUT 2: Connect to the supplied IR Blaster cable for IR signal
transmission. Place the IR Blaster in direct line-of-sight of the
equipment to be controlled.
5
RS-232 OUT TX/RX: Connect to the device that is to be controlled
via 3-pin Relay cable by RS-232 commands. For sending command
to Transmitter side, the TX and Rx pin must be reversed.
6
UPDATE: This is reserved for fi rmware update use only. Switch
this deep switch to left for fi rmware update use, under normal
operation, leave the switch on right. Update procedure may be
done from the same RS-232 port for both Transmitter and Receiver.
6
6
6.4 Receiver Left and Right Panels
OPT.
IN HDMI OUTLAN
OPT.
IN
ARC
IN
CAT5e/6/7 IN
12 3 4 5
Left Right
1
CAT5e/6/7 IN: Connect to the Transmitter unit with a single
CAT5e/6/7 cable for transmission of all data signals. The yellow LED
will illuminate to represent the link from Receiver is steady, when
it blink irregularly it represent the link error or when not illuminate
it means no link with Receiver. The green LED will illuminate to
represent the PoE function active.
2
LAN: Connect to a PC or Laptop to the internet or network
connection. The yellow LED will illuminate to represent the link with
Transmitter is steady, when it blink irregularly it represent the link
error or when not illuminate it means no link with Receiver. The
green LED will illuminate to represent the Ethernet speed is with
100Mbit/s.
3
OPT. IN: Connect to audio source equipment such as DVD or Blu-
ray player for audio signal sending to Transmitter’s OPTICAL OUT.
4
ARC IN or OPT. IN SWITCH: Switch this switch to select ARC channel.
Switch to ARC in to use HDMI OUT’s audio or switch to Optical IN to
use Optical 1’s audio.
Note: Depending on the connected devices of the HDMI OUT &
Optical in, the ARC input/output transmission distance may be
varied. It is suggested to use cable within 2 meters long to ensure
the best audio quality.
5
HDMI OUT: Connect to a HDMI equipped TV/monitor for display of
the HDMI input source signal.
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere CYP Extender Handbücher
CYP
CYP CH-1106TX & RX Bedienungsanleitung
CYP
CYP PU-106 Bedienungsanleitung
CYP
CYP CIR-03 Bedienungsanleitung
CYP
CYP PUV-1620A-RX Bedienungsanleitung
CYP
CYP CH-506TX Bedienungsanleitung
CYP
CYP Suprex SPX-7400 Series Bedienungsanleitung
CYP
CYP PU-506-KIT Bedienungsanleitung
CYP
CYP PU-1107-KIT Bedienungsanleitung
CYP
CYP IP-7000TXWP Bedienungsanleitung
CYP
CYP PU-1107-KIT Bedienungsanleitung
CYP
CYP CH-1107EX Bedienungsanleitung
CYP
CYP PU-USB-AL Bedienungsanleitung
CYP
CYP CH-501TX Bedienungsanleitung
CYP
CYP CH-1601TXRX Bedienungsanleitung
CYP
CYP IR-EXT3 Bedienungsanleitung
CYP
CYP CPLUS-VHHE Bedienungsanleitung
CYP
CYP PU-607BDWP-TX Bedienungsanleitung
CYP
CYP PUV-1250PL-TX Bedienungsanleitung
CYP
CYP SDV-FTX Bedienungsanleitung
CYP
CYP CH-U350TX Bedienungsanleitung
