CYP CSC-5500 Bedienungsanleitung
DRAFT
CSC-5500
Multi Input Scaler
Operation Manual
Operation Manual
DRAFT
DRAFT
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2011 by Cypress Technology.
All Rights Reserved.
Version VR1.0 November 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
DRAFT
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE
RDV1 03/12/12 Preliminary Release
RDV2 08/04/13 RS-232 Command
DRAFT
CONTENTS
1. Introduction............................................ 1
2. Applications........................................... 1
3. Package Contents ................................ 1
4. System Requirements............................ 1
5. Features.................................................. 1
6. Operation Controls and Functions....... 2
6.1 Front Panel ........................................2
6.2 Rear Panel.........................................3
6.3 Remote Control................................4
6.4 RS-232 Protocols ...............................5
6.5 RS-232 Commands...........................6
6.6 OSD MENU.........................................8
7. Connection and Installation............... 11
8. Specications ...................................... 12
8.1 Support I/O Resolution...................13
DRAFT
1
1. INTRODUCTION
The Multi Input Scaler has CV, Component, PC, and HDMI inputs and
can scale the signal into HDMI, VGA with audio output ports. This high
performance multi input scaler supports HDMI output resolution up to
1080p /WUXGA and Analog Digital Conversion (ADC) & Digital Analog
Conversion (DAC) allowing a wide range of AV signal to be insert to a
high-Denition signal and displaying. Further, with OSD, remote, RS-232,
Telnet and on-panel controls that makes whole for this Digital Video
Scaler a friendly using device.
2. APPLICATIONS
• Lecture hall
• Meeting room
• Conference hall
3. PACKAGE CONTENTS
• Multi Input Scaler
• Remote Control (CR-122)
• D-Sub to RCA adaptor cable
• Power Adaptor
• Operation Manual
4. SYSTEM REQUIREMENTS
Input source equipments such as Blu-ray/DVD players or PC/NB,
output display and amplier or speakers.
5. FEATURES
• Supports multi AV inputs to HDMI or PC/HD outputs
• Supports EDID and HDCP
• Supports 3D de-interlace, noise reduction and 3D Comb lter
• Supports frame rate conversion
• Supports RS-232, Telnet & Controls
• Support output timing hot keys switching
• HDMI compatible with DVI
DRAFT
2
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
1 2
POWER CV COMP PC 1 PC 2 PC 3 HDMI 1 HDMI 2 HDMI 3MENU
XGA
ENTER
-
+
720P
3 4 5 6
1POWER & LED:
Press this button to switch ON or set the device to standby mode.
Once the device is connected with power supply the LED will
illuminate and the device will switch to ON automatically.
2IR:
This IR window receives only the IR signal from the remote control
included in the package.
3INPUT button and LEDs:
Press this button sequentially to switch in between the input sources
rotationally. LED will illuminate accordingly to the selected input
source.
4MENU:
Press this button to enter into the OSD menu.
5-/+:
Press these buttons to scrolled down and up in the OSD selection.
6ENTER:
Press this button to conrm the selection. Press this button together
with + button to switch output to XGA instantly or with - button to
switch output to 720p instantly.
DRAFT
3
6.2 Rear Panel
POWER
DC 5V
CONTROL
HDMI 2HDMI 1 PC/HD
RS232 COAX AUDIO
SERVICE
OUTPUT
HDMI 1 HDMI 2 HDMI 3 PC 1 PC 2 PC 3 Cr/Pr Cb/Pb
RL
YRLCV
AUDIO
INPUT
4 5 8
1 2 3 6 7
IR IN
1IR IN:
Plug in the IR extender cable for IR signal receiving from the
included remote control.
2SERVICE:
Reserved for factory use only.
3RS-232:
Connect with PC/NB and use RS-232 command to control the
device.
4OUTPUT:
HDMI 1 & 2: Connect to HDMI display or amplier for video or video
and audio display.
COAX: Connect to active speaker or amplier for audio output in
digital format.
When the input audio source signal is with bitstream format and
the audio source setting is at Auto, coaxial output will bypass the
input audio signal which may be 5.1CH or 7.1CH according to
audio input format.
AUDIO: Connect to active speaker or amplier for audio output in
stereo format.
PC/HD: Connect to monitor/display for video output display. For
HD output,use D-Sub 9pin to 3 RCA adaptor cable for output HD
timing from 480p~1080p.
5INPUT:
HDMI 1~3: Connect to HDMI source equipment such as Blu-ray/
DVD player for both video and audio signal sending.
PC 1~3: Connect with PC/NB source equipment for video signal
input with D-Sub 15pin cable.
L/R: Connect to source equipment’s L/R output corresponding
tothe input jack below with 3.5Ø phone jack for audio signal
DRAFT
4
sending.The priority audio input of HDMI is from HDMI, only when
HDMI input has no audio signal the L/R audio will be inserted
into.
YCbCr/HDPbPr + L/R: Connect to source equipment such as video/
DVD player for both video and audio signal sending.
CV + L/R: Connect to source equipment such as video/DVD player
for both video and audio signal sending.
5CONTROL:
This port is the link for Telnet or Web GUI controls, connect to an
active Ethernet link with an RJ45 terminated cable (for further
details, please refer to section.
6POWER:
Switch this power toggle to turn on and activate the device or to
turn off to shut it down.
7DC 5V:
Plug the power adaptor included in the package and connect it
to the AC wall outlet for power supply.
6.3 Remote Control
1POWER: Press this button to switch
ON or set the device to standby
mode. Once the device is
connected with power supply.
2HDMI1~3/PC1~3/CV/COMP: Press
these hot keys to switch input
source instantly.
3EXIT: Press this button to exit the
menu or the current selection under
OSD.
4MENU: Press this button to enter into
the OSD menu.
5 OK & ▲▼◄►: Press OK to conrm
the selection or press the arrow
buttons to scrolled in the OSD
selections.
6RESET: Press this button to set the
device back into the factory default
setting.
CR-122
POWER
PC1PC2 PC3
CV COMP
EXIT MENU
OK
RESET AUTO
ADJUST
3
6
1
4
7
5
8
2
HDMI2HDMI1 HDMI3
DRAFT
5
7AUTO ADJUST: Press this button when output image is not tting the
display's screen perfectly. The device will auto adjust the image to
full screen.
8 ◄►: Press right and left buttons to increase and decrese the
volume.
6.4 RS-232 Protocols
CSC-5500
►
◄
Remote Control
PIN Assignment PIN Assignment
1 NC 1 NC
2Tx 2Rx
3Rx 3Tx
4 NC 4 NC
5 GND 5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
Baud Rate: 19200bps
Data bit: 8 bits
Parity: None
Flow Control: None
Stop Bit: 1
Andere Handbücher für CSC-5500
2
Inhaltsverzeichnis
Andere CYP Medienkonverter Handbücher
CYP
CYP CP-290 Bedienungsanleitung
CYP
CYP CLUX-SDI2HCA Bedienungsanleitung
CYP
CYP DCT-3 Bedienungsanleitung
CYP
CYP CP-255I Bedienungsanleitung
CYP
CYP CP-1261D Bedienungsanleitung
CYP
CYP CLUX-SDI2DVIA Bedienungsanleitung
CYP
CYP AU-11DD Bedienungsanleitung
CYP
CYP AU-D160 Bedienungsanleitung
CYP
CYP CLUX-SDI2VS Bedienungsanleitung
CYP
CYP CDM-160 Bedienungsanleitung
CYP
CYP CSC-5500 Bedienungsanleitung
CYP
CYP EL-6010-4K22 Bedienungsanleitung
CYP
CYP AU-D2 Bedienungsanleitung
CYP
CYP CH-2D3D Bedienungsanleitung
CYP
CYP nT15FX06 Bedienungsanleitung
CYP
CYP CPT-385AMN Bedienungsanleitung
CYP
CYP CDPH-1S Bedienungsanleitung
CYP
CYP CETH-4HDMI Bedienungsanleitung
CYP
CYP CPLUS-V2PE Bedienungsanleitung
CYP
CYP CP-1261D Installationshandbuch
