CYP CSDI-12SR Bedienungsanleitung

CSDI-12SR

1 by 2 3G-SDI Scaler

Operation Manual

DISCLAIMERS

The information in this manual has been carefully checked and

is believed to be accurate. Cypress Technology assumes no

responsibility for any infringements of patents or other rights of third

parties which may result from its use.

Cypress Technology assumes no responsibility for any inaccuracies

that may be contained in this document. Cypress also makes no

commitment to update or to keep current the information contained

in this document.

Cypress Technology reserves the right to make improvements to this

document and/or product at any time and without notice.

No part of this document may be reproduced, transmitted,

transcribed, stored in a retrieval system, or any of its part translated

into any language or computer le, in any form or by any means—

electronic, mechanical, magnetic, optical, chemical, manual, or

otherwise—without express written permission and consent from

Cypress Technology.

Version 1.1 August 2011

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be

trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or

operate this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

• Always follow basic safety precautions to reduce the risk of re,

electrical shock and injury to persons.

• To prevent re or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts

inside the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the PSU

if it is damaged.

• Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow for

sufcient space for air to circulate around the unit.

REVISION HISTORY

VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE

V1 11/12/13 Preliminary Release

VS1 23/12/14 Updated text/Diagrams

CONTENTS

1. Introduction............................................ 1

2. Applications........................................... 1

3. Package Contents ................................ 1

4. System Requirements............................ 1

5. Features.................................................. 2

6. Operation Controls and Functions....... 3

6.1 Front Panel ........................................3

6.2 Rear Panel.........................................4

6.3 OSD Menu.........................................5

7. Connection Diagram ............................ 9

8. Specications ...................................... 10

8.1 Technical Specication.................10

8.2 Supported Input Resolutions .........11

8.3 Supported Output Resolutions......11

9. Acronyms ............................................. 12

1. INTRODUCTION

The 1 by 2 3G-SDI Scaler allows an SD-SDI, HD-SDI and 3G-SDI signal

to be scaled and split to two simultaneous SDI outputs, providing

bandwidth up to 2.970Gbps for 3G-SDI video support allowing the user

to distribute and extend their SDI signal. The On-screen Display (OSD)

menu can be controlled from the front panel, allowing quick and easy

adjustment of all settings.

2. APPLICATIONS

• Distribute and extend a single SDI signal to 2 SDI displays

• Scale any SDI input resolution to any SDI output resolution to SDI

standards

3. PACKAGE CONTENTS

• 1 by 2 3G-SDI Scaler

• 5 V/2.6 A DC Power Adaptor

• Operation Manual

4. SYSTEM REQUIREMENTS

SDI source equipment such as an SDI camera or any SDI signal with

SDI connection cable and output to the SDI monitors or recorders with

SDI connection cables.

5. FEATURES

• Splits an SDI input to two SDI outputs with scaler function

• Supports scaling of any SDI input to any SDI output to SDI standards

• Supports SD-SDI, HD-SDI and 3G-SDI input/output signals with auto-

detection

• SDI interface operates at bitrates of 2.970 Gbps, 2.970/1.001 Gbps,

1.485 Gbps, 1.485/1.001 Gbps and 270 Mbps

• Supports SDI input/output modes/standards:

- SD-SDI: SMPTE 259M-C, at bitrates of 270 Mbps

- HD-SDI: SMPTE 292M, at bitrates of 1.485 Gbps and 1.485/1.001 Gbps

- 3G-SDI: SMPTE 424M/425M-A & B, at bitrates of 2.970Gbps and

2.970/1.001Gbps

• Supports up to 8 audio channels at 48 kHz

• Supports SDI input/output distances up to 100 meters (3G-SDI), 200

meters (HD-SDI), or 300 meters (SD-SDI)

Note: Tested with Belden 1694A Cable. Operating distances may vary

if used with cables of different specications.

6. OPERATION CONTROLS AND FUNCTIONS

6.1 Front Panel

720p

1080p

MENUSYNCPOWERSERVICE ENTER

1 2 3 4 5 6

1SERVICE: Connect to a PC or Laptop with a mini USB B cable for

rmware update only.

2POWER LED: The LED will illuminate when the unit is connected to

an active power supply.

3SYNC LED: The LED will illuminate when the SDI input is connected

to and detects an SDI source.

4MENU: Press to bring up the OSD menu. When in OSD menu mode,

the 'MENU' button will function as the 'EXIT' button.

Press the 'MENU' and 'MINUS (-)' buttons simultaneously will

immediately switch the output resolution to 720p@60 Hz.

5ENTER: Press to conrm the selection in the OSD menu.

Press the 'ENTER' and 'PLUS (+)' buttons will immediately switch the

output resolution to 1080p@60 Hz.

6MINUS (-)/PLUS (+): Press these buttons to navigate up or down the

OSD menu.

When in normal display mode (not in OSD menu), press the 'PLUS (+)'

button to 'FREEZE' (pause) the video (Please refer to the section 6.3).

6.2 Rear Panel

DC 5VSDI OUT

SDI IN

1 2

1 2 3

1SDI IN: Connect to the SDI output of the SDI source device.

2SDI OUT 1/2: Connect to the SDI devices such as TV/displays or

recorders.

3DC 5V: Connect the 5V DC power supply to the unit and plug the

adaptor into an AC outlet.

6.3 OSD Menu

MAIN MENU SUB MENU ADJUSTMENTS DEFAULT

OUTPUT 480I59, 576I50,

720P50, 720P59,

720P60, 1080P23,

1080P24, 1080P25,

1080P29, 1080P30,

1080I50, 1080P50,

1080I59, 1080P59,

1080I60, 1080P60

720P60

EXIT

PICTURE CONTRAST 0 ~ 100 64

BRIGHTNESS 0 ~ 100 64

SATURATION 0 ~ 100 64

HUE 0 ~ 100 64

SHARPNESS 0 ~ 100 32

PICTURE RESET

EXIT

ASPECT RATIO*1 FULL FULL

16:9 TV

16:10 TV

4:3 TV

KEEP RATIO

EXIT

OVERSCAN ENABLE YES, NO NO

H SIZE% 0% ~ 50% 0%

V SIZE% 0% ~ 50% 0%

EXIT

Andere Handbücher für CSDI-12SR

Inhaltsverzeichnis

Andere CYP Medienkonverter Handbücher

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung

Expert

Expert EX-9543 Bedienungsanleitung