D-Link DG-102S Bedienungsanleitung
Comwave Home Phone Adapter
Quick Start Guide
Important: This guide describes the supported conguration for Comwave Home Phone Service. When
calling Comwave’s Technical Support Team, your network must be congured as described.
Home Phone Adapter
Package Contents
1
Connections
1 2
4
3
1 2 3 456
1 Power Adapter
2 Serial Cable
Used only if instructed by
Comwave to assist with
troubleshooting.
3 WAN
Used to connect to your High
Speed Internet modem using
the Ethernet Cable provided in
your package.
4 LAN
Used to connect to your computer using
an Ethernet Cable (if you are not using a
wireless router).
5 Phone 1
Used to connect to your telephone
handset, using your existing telephone
cord.
6 Life Line
NOTE: Dial“#”to activate this port.
Used to:
a) Connect to an existing phone
jack to access the building
intercom functions in apartment
buildings.
b) Connect to a back-up non-VoIP
land line in the event of Internet
loss, if a back-up line is available.
Output:12v 1
Start Here
Cable High Speed Internet
Go to page 3
If you have:
DSL High Speed Internet
with USERNAME and PASSWORD
DSL High Speed Internet
without USERNAME and PASSWORD
Go to page 3Go to page 5
2
Installation with a Cable Modem or DSL modem (without USERNAME and PASSWORD)
1
step
To begin installation, turn o your computer and disconnect the power adapter to
your High Speed Internet modem.
high speed
internet modem PC
telephone
power outlet
existing
cable or phone
line
2
steP
3
step
4
step
8
step
5
steP
6
steP
3
WAIT!!
2 min.
Connect an Ethernet cable from the High Speed Internet modem to the WAN
port of the Home Phone Adapter.
Connect a second Ethernet cable from the LAN port of the Home Phone Adapter
to your computer.
Connect your telephone handset to the PHONE 1 port of the Home Phone Adapter.
Connect the High Speed Internet modem to a power outlet.
Note: Please wait 2 minutes before continuing to the next step.
Connect the Home Phone Adapter to the power outlet . The Status light will blink
until it has successfully connected to the Comwave network. Once the Status
light stops ashing and becomes solid green, your phone is ready for use.
Your phone should now work.
Start your computer.
2
step
3
step
4
step
6
step
7
step
8
step
5
step
Remember to dial “1” before ALL calls, including local calls (example: 1-416-555-1234).
You will NOT be charged long distance for local calls.
Remember to dial “1” before ALL calls, including local calls (example: 1-416-555-1234).
4
1
step
To begin installation, turn o your computer and disconnect the power adapter to
your High Speed Internet modem.
Installation with a DSL modem (with USERNAME and PASSWORD)
high speed
internet modem PC
telephone
power outlet
existing
phone
line
2
steP
3
step
4
step
8
step
5
steP
6
steP
5
WAIT!!
2 min.
Connect an Ethernet cable from the High Speed Internet modem to the WAN port
of the Home Phone Adapter.
Connect a second Ethernet cable from the LAN port of the Home Phone Adapter
to your computer.
Connect your telephone handset to the PHONE 1 port of the Home Phone Adapter.
Connect the High Speed Internet modem to a power outlet.
Note: Please wait 2 minutes before continuing to the next step.
Connect the Home Phone Adapter to the power outlet.
Start your computer. Open a browser window, type “http://192.168.122.1:8089”
into the address eld and press the “Enter” key.
5
step
4
Continue to Step 8
7
step
step
3
step
2
step
6
step
6
Installation with a DSL modem (with USERNAME and PASSWORD)
Enter the following User Name
and Password, and click “OK”:
8
step
9
step
In the left menu, click on “Cong IP”
and then select “Cong Device IP Address”.
USER NAME: root
PASSWORD: admin
4
In the bottom right corner of the main
window, click the “Save” button . Then
on the left menu, select “Save Changes”
11
step
8
In the main window (under the section
called “PPPoE Settings”), ensure that the
dropdown menu is set to “enabled” .
Fill in the User Name and Password
provided by your Internet Service
Provider.
Note: It is important to be very accurate.
The user name and password are case
sensitive. Any mistakes will prevent your
Comwave Home Phone from working.
10
step
a
b
a
b
.
Installation with a DSL modem (with USERNAME and PASSWORD)
In the main window, click on the “Save Conguration” button. Your Comwave Home
Phone will reboot.
12
step
Andere Handbücher für DG-102S
7
Inhaltsverzeichnis
Andere D-Link Adapter Handbücher
D-Link
D-Link DUB-1312 Bedienungsanleitung
D-Link
D-Link DUB-1210 Bedienungsanleitung
D-Link
D-Link DWA-192 Bedienungsanleitung
D-Link
D-Link DFE-570TX Bedienungsanleitung
D-Link
D-Link AirPro DWL-A650 Bedienungsanleitung
D-Link
D-Link DFE-550TX Bedienungsanleitung
D-Link
D-Link DHP-501AV Bedienungsanleitung
D-Link
D-Link DHP-329AV Bedienungsanleitung
D-Link
D-Link DWM-156 Handbuch
D-Link
D-Link DWM-156 Bedienungsanleitung
D-Link
D-Link AirPremier DWL-G680 Bedienungsanleitung
D-Link
D-Link DUB-E100 Bedienungsanleitung
D-Link
D-Link DWA-171 Bedienungsanleitung
D-Link
D-Link DGE-550SX Bedienungsanleitung
D-Link
D-Link DHP-301 - PowerLine HD EN Starter Bedienungsanleitung
D-Link
D-Link DWA-110 Bedienungsanleitung
D-Link
D-Link DHP-P600AV Bedienungsanleitung
D-Link
D-Link DBT-122 Bedienungsanleitung
D-Link
D-Link DHP-P500AV Bedienungsanleitung
D-Link
D-Link DWA-582 Bedienungsanleitung
