D-Link DVG-2001S Bedienungsanleitung
Version 1.0
DVG-2001S
VoIP Terminal Adapter
2 D-Link Systems, Inc.
DVG-2001S Install GuideSystem Requirements
System Requirements
Computer with Windows® XP or 2000
Internet Explorer 6.0 or Netscape® Navigator 7.0 and above
An available Ethernet port on the network
An active subscription to a VoIP Broadband Phone Service
Manual and Software
on CD
Package Contents
D-Link DVG-2001S
VoIP Terminal Adapter
Ethernet Cable 12V 1.2A Power Supply
It’s best to use the same computer that is connected to your router for
configuring the DVG-2001S VoIP Terminal Adapter when connecting
directly to a cable or DSL modem.
If any of the above items are missing, please contact your reseller.
Using a power supply with a different voltage
rating will damage this product and void its
warranty.
D-Link Systems, Inc. 3
DVG-2001S Install Guide Hardware Overview
Front Panel
LAN LED
Solid indicates an Ethernet connection. Blinking
indicates traffic at the Ethernet port.
Power LED
Solid indicates a connection to
a good power source. Blinking
indicates startup or a reboot.
Phone LED
A solid light indicates that the phone
is off the hook (in use). A blinking
LED indicates an incoming call.
Rear Panel
Power Receptor
Receptor for the supplied
power adapter.
LAN Port
Connects to your Ethernet network. The LAN
port supports Auto MDI/MDI-X, allowing you to
connect a straight-through or crossover cable.
Phone Port
Connect to your phone using
a standard phone cable.
Reset Button
With the power off, hold the
reset button using a paper clip
and power on the unit. Hold for 5
seconds and release.
4 D-Link Systems, Inc.
DVG-2001S Install GuideConfiguration
Set your PC’s IP address to 192.168.0.2
and the subnet mask to 255.255.255.0.
The default gateway and primary DNS
server IP addresses can be left blank
at this time.
Click OK.
Configuration
If you are going to connect the DVG-2001 to a D-Link router using the default
LAN IP address (192.168.0.1), or to an existing network with a network IP of
192.168.0.xxx, plug the DVG-2001 into the router using an Ethernet cable and
skip to page 5. The default IP address of the DVG-2001 is 192.168.0.80.
If you are setting up the DVG-2001S for the first time, you will need to connect
the unit directly to a computer for configuration.
Insert one end of the Ethernet cable into the Ethernet (LAN) port on the back
panel of the DVG-2001S and the other end of the cable to an Ethernet adapter
on your computer.
Connect the power adapter to the power input at the back panel of the VoIP
Adapter and then plug the other end of the power adapter to a wall outlet or
power strip. On the front of the device, the Power LED will turn ON to indicate
proper operation.
Windows 2000/XP: Go to Start > right-click My Network Places > select
Properties > Right-click Local Area Connection > select Properties >
double-click Internet Protocol (TCP/IP). Remember your original settings
since you will change them back when completing the configuration of the
DVG-2001S.
D-Link Systems, Inc. 5
DVG-2001S Install Guide Configuration
Click on Run Wizard.
Click Next.
Open a web browser and type in the IP
address of the DVG-2001S.
To access the web-based configuration utility, open a web browser such as
Internet Explorer and enter the IP address of the DVG-2001S (192.168.0.80).
Configuration (continued)
Click Next.
Select to use a dynamic IP address
(assigned by your DHCP server) or a
Static IP address (recommended).
6 D-Link Systems, Inc.
DVG-2001S Install GuideConfiguration
Click Next.
Configuration (continued)
If you selected Static, enter the IP
address, subnet mask, default gateway,
and DNS server(s). The default gateway
and primary DNS server must be the
(LAN) IP address of your router.
Setup is finished. Click Restart to
reboot the DVG-2001S. If you have
selected Dynamic, the DVG-2001
will obtain an IP address from your
DHCP server. You must use the new
IP address to access the web-based
configuration utility on the DVG-2001.
Click Restart.
D-Link Systems, Inc. 7
DVG-2001S Install Guide Installation Overview
Once you are finished configuring the DVG-2001G, disconnect the Ethernet
cable that is connecting the DVG-2001S to your computer. Connect your
computer back to your network and then connect the DVG-2001S to your router
or switch (hub). Connect your phone using a standard phone cable and insert
it into the Phone port on the DVG-2001S. You must have an account and be
provisioned with a VoIP service provider before using your phone.
Once you’ve completed your DVG-2001S installation, your network may appear
similar to the diagram below.
Note that an electrical power outage or a broadband provider outage will prevent operation of the
VoIP phone, including for emergency purposes (e.g. calling 911).
Installation Overview
8 D-Link Systems, Inc.
DVG-2001S Install GuideVoIP Basics
Making and Receiving Calls:
Placing a call is exactly the same as with any other regular phone. Just pick up
the handset and dial the regular telephone number. It’s that simple. Receiving
calls also works the same. The phone will ring just like a regular phone. With
VoIP, just pick up the phone and start talking!
In more technical terms, your D-Link VoIP Adapter splits converts your analog
signal to digital. The digital signal is sent through your modem and across the
Internet.
When someone calls you, they dial your regular telephone number. Behind the
scenes, your number looks similar to an e-mail address. This number instructs
the call to travel over the Internet to the D-Link VoIP Adapter, your phone rings,
and all you have to do is pick up and answer it.
How does it work?
VoIP technology converts your voice (or analog) into data (or digital signal)
allowing you to place and receive calls over your broadband connection. Simply
plug a D-Link Broadband VoIP Router in to your Cable or DSL Modem, and
plug a standard household telephone into it. You can then place and receive
calls over this phone and also have additional control functions available to you
through a Web browser.
How can I find my IP address and phone number?
Using a phone that is attached to the DVG-2001S, dial the following 3 digits
and you will receive a voice reading back your IP address or phone number.
**1 - IP address
**2 - Phone number
VoIP Basics
D-Link Systems, Inc. 9
DVG-2001S Install Guide Appendix
Go to the Apple Menu > select System
Preferences > click Network.
Input your IP Address and Subnet Mask
(assign a unique IP address within the same
range as your network).
No two computers can have the same IP
address.
Click Network.
Select Built-in Ethernet from
the Show drop-down menu.
Select Manually from the
Configuration drop-down menu.
Click Apply Now.
IP Address Configuration - Mac OSX
10 D-Link Systems, Inc.
DVG-2001S Install GuideNotes
Notes
Andere Handbücher für DVG-2001S
4
Inhaltsverzeichnis
Andere D-Link Adapter Handbücher
D-Link
D-Link DIR-300 - Wireless G Router Bedienungsanleitung
D-Link
D-Link DWL-P50 Bedienungsanleitung
D-Link
D-Link AirPlus G DWL-G650X Bedienungsanleitung
D-Link
D-Link DWA-110 Bedienungsanleitung
D-Link
D-Link DWA-171 Bedienungsanleitung
D-Link
D-Link DUB-1312 Bedienungsanleitung
D-Link
D-Link PCMCIA WIRELESS ASAPTER DWL-650 Bedienungsanleitung
D-Link
D-Link DU-520 Bedienungsanleitung
D-Link
D-Link DUB-E130 Bedienungsanleitung
D-Link
D-Link PowerLine AV 500 Mini Bedienungsanleitung
D-Link
D-Link DWA-556 Bedienungsanleitung
D-Link
D-Link Powerline DHP-300 Bedienungsanleitung
D-Link
D-Link PCMCIA WIRELESS ASAPTER DWL-650 Bedienungsanleitung
D-Link
D-Link PowerLine DHP-500AV Bedienungsanleitung
D-Link
D-Link DWA-127 Bedienungsanleitung
D-Link
D-Link DUB-E100 Bedienungsanleitung
D-Link
D-Link WNA-2330 - Rangebooster G Cardbus 802.11G... Bedienungsanleitung
D-Link
D-Link Vectra VL410 Bedienungsanleitung
D-Link
D-Link DGE-530T Bedienungsanleitung
D-Link
D-Link DWL-G520M Bedienungsanleitung
