D-Link AirPremier N DAP-2690 Bedienungsanleitung

D-Link AirPremier N Concurrent

Dual Band PoE Outdoor AP

Refe

Reproduction in any manner whatsoever without the written permission of D-Link. is strictly forbidden.

Trademarks used in this text: D-Link DAP-2690 is trademarks of D-Link.

Other trademarks and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. D-Link disclaims any proprietary interest in trademarks and

trade names other than its own.

Table of

ont

TABLE OF

NTENT

................................................................................................................................. 3

INTRODUCTION............................................................................................................................................... 4

COMMAND SYNTAX AND CONVENTIONS ................................................................................................. 4

USING A COM PORT TO CONNECT TO DAP-2690 ..................................................................................... 5

USING A TERMINAL TO CONNECT TO THE CONSOLE PORT ............................................................... 5

COMMANDS AND THEIR DESCRIPTIONS .................................................................................................. 8

TILITY

OMMANDS

............................................................................................................................................ 8

THERNET

OMMANDS

........................................................................................................................................ 9

IRELESS

OMMANDS

....................................................................................................................................... 10

ULTI

-SSID

OMMANDS

.................................................................................................................................. 12

VLAN

OMMANDS

............................................................................................................................................. 13

RRAY

OMMANDS

..................................................................................................................................... 13

CCESS

ONTROL

IST

OMMANDS

................................................................................................................ 15

DHCP

ERVER

OMMANDS

.............................................................................................................................. 15

IME

ISPLAY

SNTP

OMMANDS

................................................................................................................ 16

YSTEM

OMMANDS

.................................................................................................................................. 16

THER

OMMANDS

............................................................................................................................................ 16

TATUS AND

TATES

.......................................................................................................................................... 17

ANAGEMENT

..................................................................................................................................................... 17

CONFIGURATION EXAMPLE ...................................................................................................................... 18

Introduction

The Command Line Interface (CLI) is a network management application operated through an ASCII

terminal without the use of a Graphic User Interface (GUI) driven software application. By directly

entering commands, the user has greater configuration flexibility. The CLI is a basic command-line

interpreter similar to the UNIX C shell.

A wireless router can be configured and maintained by entering commands from the CLI, which is based

solely on textual input and output with commands being entered by a terminal keyboard and the output

displayed as text via a terminal monitor. The CLI can be accessed from a console terminal connected to

an EIA/TIA-232 port or through a Telnet session. For this CLI we shall use the “Tera Term”program.

This guide describes how the Command Line Interface (CLI) is structured, describes the command

syntax, and describes the command functionality.

This guide also provides information for configuring the DAP-2690, details the procedures and provides

configuration examples. Basic installation configuration is described in the User’s Guide and must be

completed before using this document.

Command Syntax and Conventions

A command is one or more words that can be followed by one or more keywords and parameters.

Keywords and parameters can be required or optional:

•A keyword is a predefined string (word) that narrows down the scope of a command. A keyword can

be followed by an associated parameter or by associated keywords. In many cases, these associated

keywords are mutually exclusive, so you need to select one of them. In some cases, this manual

refers to a group of words as a keyword.

•A parameter is a variable for which you need to type a value. You need to replace the parameter

name with the appropriate value, which might be a name or number. A parameter can be

associated with a command or with a keyword.

This manual lists each command by its full command name and provides a brief description of the

command. In addition, for each command, the following information is provided:

•Format. Shows the command keywords and the required and optional parameters.

•Mode. Identifies the command mode you need to be in to access the command. (With some

minor exceptions, the mode is always described using lower-case letters.)

•Related show command or commands. Identifies and links to the show command or commands

that can display the configured information.

For more complicated commands, in addition to the format, mode, and related show command or

commands, the following information is provided:

•Table. Explains the keywords and parameters that you can use for the command.

•Example. Shows a CLI example for the command.

Using a COM port to connect to DAP-2690

The back panel of the DAP-2690 provides an RJ45 Ethernet port to connect an RS-232 connector to

your PC for monitoring and configuration.

To use the console port, the following equipment is needed:

1. A terminal or a computer with both an RS-232 serial port and the ability to emulate a

terminal.

2. A console cable with a male DB-9 connector on one end and an RJ-45 connection on the

other. It establishes the physical connection to the console port.

Using a terminal to connect to the console port

Connect the male DB-9 connector on the console cable to the RS-232 serial port on the computer

running terminal emulation software then insert the RJ-45 connector into the RJ-45 console port on the

front of the Switch.

Set the terminal emulation software as follows:

•Select the appropriate serial port (COM1 or COM2).

•Set the data rate to 115200 baud.

•Set the data format to 8 data bits, 1 stop bit, and no parity.

•Set flow control to none.

•Under Properties, select VT100 for Emulation mode.

Select Terminal keys for Function, Arrow and Ctrl keys. Make sure to use Terminal keys (not Windows

keys) are selected.

Telnet 192.168.0.50 on the command prompt

Hit the Enter key a couple of times to access the login phase.

Type admin at the login prompt and press the Enter key.

Leave Password blank by depressing the Enter key again.

The command prompt now displays

0->

Type “help”or use the question symbol, “?”then press Enter to access a list of commands.

When you enter a command without all of its required parameters, the CLI prompts you with a list of possible

completions. For example, type “tftp”, the screen below shows other helpful hits for you to complete your

configuration options.

When you enter a command without a variable or value that needs to be specified, the CLI will prompt you

with further information about what is needed to complete the command.

For example, if you type in snmp delcomm, the missing value,

CommunityString<string>

is displayed in

order so that you can complete the instruction.

Commands and their Descriptions

Utility Commands

help

Display CLI Command List

ping

Send ICMP ECHO_REQUEST to network hosts

set factorydefault

Restore to factory default setting

reboot

Reboot Access Point. It is necessary to reboot the AP after

making Configuration changes for those changes to take effect.

ssl freset

Use freset to factorydefault

get bootcodeinfo

Display bootcode information

version

Displays the currently loaded firmware version

get cpuinfo

Display cpu info percentage

get meminfo

Display mem info percentage

get hardware

Display Hardware Revisions

get macaddress

Display Mac address

get country

Display Country

get pingctl

Display Ping Control state

get inact

Display the value of a specific inact

set pingctl

Set Ping Control

get uptime

Display UpTime

get time

Display time

pwd

Print name of current/working directory

set apply

Apply the seting

set time

Set time (year month day hour min sec)

clear language-pack

Clear language pack

set inact

Set the value of a specific inact

tftp getconfig

Use tftp to get configuration from PC

tftp getfirmware

Use tftp to get Firmware from PC

tftp putconfig

Use tftp to put configuration to PC

tftp getxmlconfig

Use tftp to get xml configuration from PC

tftp putxmlconfig

Use tftp to put xml configuration to PC

get web

Display WEB Information

get webredirect_state

Display Web Redirect State

get webredirect_list

Display Web Redirect Account List

set web

Set WEB Status

set webredirect

Set Web Redirect

Ethernet Commands

get ipaddr

Display IP Address

get ipmask

Display IP Network/Subnet Mask

get gateway

Display Gateway IP Address

get ipmode

Display IP Mode

get eth-updownlink

Display ethernet uplink/downlink state

get updownlink

Display primary ssid uplink/downlink state

get uplink_bandwidth

Display uplink bandwidth

get downlink_bandwidth

Display downuplink bandwidth

get nameaddr

Display DNS Address

get ipv6

Display IPv6 settings

set ipaddr

Set IP Address

set ipmask

Set IP Network/Subnet Mask

set gateway

Set Gateway IP Address

set ipmode

Set IP Mode(Static or Dynamic)

set eth-updownlink

Set ethernet uplink/downlink state

set fixedrate

Set Fixed Rate

set nameaddr

Set DNS Address

set uplink_bandwidth

Set uplink bandwidth

set downlink_bandwidth

Set downlink bandwidth

set updownlink

Set primary ssid uplink/downlink state

Wireless Commands

get apmode

Display AP Operate Mode

get band

Display current Band

get ssid

Display Service Set ID

get ssidhidden

Display SSID hidden Mode as enabled or disabled

get autochannel

Display AutoChannel

get channel

Display Channel

get ch_env

Display channel environment

get availablechannel

Display available channel list

get cwm

Display CWM

get wireless

Display Wireless

get wlmode_db

Display Wlmode

get fixedrate

Display Fixed Rate

get beaconinterval

Display Beacon Interval

get dtim

Display Delivery Traffic Indication Message Beacon Rate

get txpower

Display Txpower

get wmm

Display WMM

get acktimeout

Display ACKTIMEOUT

get shortgi

Display Shortgi

get igmpsnoop

Display IGMP Snoop

get assoclimitstatus

Display Association Limit setting status

get mcastrate

Display mcast rate

get wlancount

Display wlan count

get wlan_utilization

Get Wlan utilization

set apmode

Set AP Operate Mode

config wlan

Set AP Band (0:2.4G/1:5G)

set band

Set ap band (2.4G or 5G)

set ssid

Set Service Set ID

set ssidhidden

Set ssidhidden

set autoChannel

Set AutoChannel

set channel

Set Channel (1--11)

set cwm

Set CWM

set wireless

Set Wireless

set wlmode_db

Set Wlmode

set beaconinterval

Set Beaconinterval (range:25--500)

set dtim

Set DTIM (1--15)

set txpower

Set Txpower

set wmm

Set WMM

set acktimeout_a

Set acktimeput in A band (range:25--200)

Andere Handbücher für AirPremier N DAP-2690

Inhaltsverzeichnis

Andere D-Link Netzwerk-Router Handbücher

D-Link

D-Link DSL-2542B Bedienungsanleitung

D-Link

D-Link DIR-300 - Wireless G Router Bedienungsanleitung

D-Link

D-Link DIR-120 Bedienungsanleitung

D-Link

D-Link DIR-819 Bedienungsanleitung

D-Link

D-Link DIR-625 Router Bedienungsanleitung

D-Link

D-Link Express Ethernetwork DI-704P Bedienungsanleitung

D-Link

D-Link DIR-506L Bedienungsanleitung

D-Link

D-Link DGS-1210-28P Bedienungsanleitung

D-Link

D-Link DIR-518L Bedienungsanleitung

D-Link

D-Link DWR-921E Bedienungsanleitung

D-Link

D-Link DES-1526 Bedienungsanleitung

D-Link

D-Link DSL-520T Bedienungsanleitung

D-Link

D-Link DSL-2542B Bedienungsanleitung

D-Link

D-Link DGS-1510/ME Series Bedienungsanleitung

D-Link

D-Link DIR-875 Bedienungsanleitung

D-Link

D-Link DSL-G2452DG Bedienungsanleitung

D-Link

D-Link DIR-300 - Wireless G Router Bedienungsanleitung

D-Link

D-Link Ethernet Switches Bedienungsanleitung

D-Link

D-Link DWR-978 Bedienungsanleitung

D-Link

D-Link DSL-502T Bedienungsanleitung

D-Link

D-Link DAP-300P Bedienungsanleitung

D-Link

D-Link N300 Bedienungsanleitung

D-Link

D-Link DSL-2750U Bedienungsanleitung

D-Link

D-Link DSL-3782 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise