D-Link DSS-100E-18P Bedienungsanleitung

Documentation is also available

on the D-Link website

This document will guide you through the basic

installation process for your new D-Link

18-Port Unmanaged PoE Switch

DSS-100E-18P

Quick Installation Guide

1718

ENGLISH

# LED Status Description

Link/Act/

Speed

(Ports 17

to 18)

Solid

green

There is an active link negotiated at

10/100/1000 Mbps on this port.

Blinking

green

There is trac on the port at 10/100/1000

Mbps.

O No link

PoE

(Ports 1

to 16)

Solid

amber

The port is providing power to the

connected PoE-powered device.

O

There is no PoE-powered device

connected to this port or PoE-powered

device insert but failure occurs. (PSE can’t

provide power to PD due to PD error or

power budget is not enough.)

Table 1

Note: The LED behavior for ports 1-16 will switch

between Link mode and PoE mode when the PoE mode

is active. Port 1 ~ Port 16 PoE power budget is 30

watts/port. Total PoE Power budget is 230 watts.

Front Panel Connectors

Figure 2

#Item Description

1Ports 1 ~16

10/100 Mbps PoE-capable ports for

connecting Ethernet devices and PoE-

powered devices.

2Port 17

10/100/1000 Mbps Ethernet uplink port

for connecting to another switch using an

Ethernet cable.

3Port 18

10/100/1000 Mbps GbE/SFP combo uplink

port for connecting to another switch using an

Ethernet cable or installing a compatible SFP

transceiver.

Table 2

Rear Panel Connectors

Figure 3

#Item Description

1Switch GND This is used to connect the switch to ground.

2Power Input This is used to connect the power cable to the

switch.

Table 3

Before You Begin

This Quick Installation Guide gives you step-by-step

instructions for setting up your DSS-100E-18P 18-

Port Unmanaged PoE Switch. The model you have

purchased may appear slightly dierent from the

one shown in the illustrations. For more detailed

information about the switch, please refer to the

User Manual.

Package Contents

This DSS-100E-18P package should include the

following items:

• 1 x DSS-100E-18P

• 1 x Power cord

• 1 x Rack mount kit and rubber feet

• 1 x Quick Installation Guide

If any of the above items are damaged or missing,

please contact your local D-Link reseller.

Hardware Overview

LED Indicators

Figure 1

# LED Status Description

1Power

Solid

green

The device is powered on.

O The device is powered o.

2PoE Max

Solid red

Indicates that the total PoE power output

of the switch has exceeded the Guard

Band threshold of 223 W, but is still below

the total budget of 230 W.

O The total PoE power consumption is below

the 223 W Guard Band threshold.

Link/Act/

Speed

(Ports 1

to 16)

Solid

amber

There is an active link negotiated at 10/100

Mbps on this port.

Blinking

amber

There is trac on the port at 10/100 Mbps.

O No link

910 11 12 13 14 15 16 17 18

Act

Link /

1000

910 11 12 13 1415 16 17 18 Act

Link /

1000

1 3 5

ENGLISH

Grounding the Switch

This section describes how to connect the switch

to the ground. You must complete this procedure

before powering on the switch.

Required Tools and Equipment:

• One M4 x 6 mm (metric) pan-head screw

(included in the accessory kit).

• Grounding cable (not included in the accessory

kit): The grounding cable should be sized

according to local and national installation

requirements. Depending on the power supply

and system, a 12 to 6 AWG copper conductor is

required for installation. Commercially available

6 AWG wire is recommended. The length of the

cable depends on the proximity of the switch to

proper grounding facilities.

• A screwdriver (not included in the accessory kit).

You can connect the switch to a protective ground

by following the steps below:

1. Verify if the system power is o.

2. Use the grounding cable to place the #8 terminal

lug ring (not included in the accessory kit) on top

of the ground-screw opening.

3. Insert the grounding screw into the ground

screw opening.

4. Using a screwdriver, tighten the grounding screw

to secure the grounding cable to the switch.

5. Attach the terminal lug ring at the other end

of the grounding cable to an appropriate

grounding stud or bolt on the rack where the

switch is installed.

6. Verify that the ground connections on the switch

and the rack are securely attached.

DIP Switches

The DIP switches on the front panel allow easy

conguration of the advanced features of the

DSS-100E-18P

DIP

Switch Function Controlled Default

Standard

Switch all ports can communicate with each

other port and work as a common Unmanaged

Switch. *1 to 16 port supports Power over Ethernet

and transmit data at 10/100 Mbps.** 1 to 8 port

supports port priority to optimize port cache.

Isolate

1 to 16 port can’t communicate with

each other, but each of them can

communicate with port 17 and 18.

O

Extend

The data rate of 9 to 16 port is limited to 10Mbps,

whereas the maximum transmission distance

of the port is increased to 250 meters.

O

Table 4

Hardware Installation

Before You Begin

Observe the following precautions to help prevent

shutdowns, equipment failures, and personal injury:

• Install the DSS-100E-18P in a cool and dry

place. Refer to the technical specications in

the user manual for the acceptable operating

temperature and humidity ranges.

• Install the switch in a site free from strong

electromagnetic sources, vibration, dust, and

direct sunlight.

• Leave at least 10 cm of space to the left and right-

hand side of the switch for ventilation.

• Visually inspect the power connector and make

sure that it is fully secured to the power cord.

• Do not stack any devices on top of the switch.

910 11 12 13 1415 16 17 18 Act

Link /

1000

910 11 12 13 14 15 16 17 18 Act

Link /

1000

ENGLISH

Using the Switch on a Flat Surface

The included rubber pads can be placed on the

bottom of the device to prevent it from damaging

the surface it is placed on.

1. Remove the rubber pads from the adhesive strip.

2. Stick one pad on each corner on the bottom

panel of the switch.

Figure 4

Mounting the Switch in a Rack

The DSS-100E-18P can be mounted into a standard

19” server rack.

1. Attach the included mounting brackets to the

sides of the switch and secure them using the

provided screws.

Figure 5

2. Install the switch into the rack.

3. Use the screws that were provided with the rack

to secure the switch to the rack.

Figure 6

Grounding the Switch

This step must be completed before powering on

the switch.

Required tools and equipment for grounding

• Grounding screw (included) and one M4x6

(metric) pan-head screw (not included).

• Grounding cable (not included). The grounding

cable should be sized according to local and

national installation requirements. Depending

on the power supply and system, a 12 to 6 AWG

copper conductor is required for installation.

Commercially available 6 AWG wire is

recommended.The length of the cable depends

on the proximity of the switch to proper

grounding facilities.

• A screwdriver (not included).

Note: Verify that the system is powered o.

1. Remove the grounding screw from the back of

the device and place the #8 terminal lug ring of

the grounding cable on top of the grounding

screw opening.

2. Insert the grounding screw back into the screw

opening and use a screwdriver to tighten the

grounding screw.

3. Attach the terminal lug ring at the other end

of the grounding cable to an appropriate

grounding source.

4. Verify that the connection between the

grounding connector on the switch and the

grounding source is secure.

Powering On the Switch

1. Connect the power cord to the power connector

on the switch.

2. Plug the other end of the power cord into a

nearby power socket.

Connecting to the Network

The switch can be integrated into the network

through one of the following connection methods:

Switch to End Node or Powered Device

Use a standard Ethernet cable to connect the switch

to PCs with an 10/100/1000 Mbps RJ-45 interface,

or connect and power remote IEEE 802.3af/at-

compliant devices, such as IP cameras or IP phones

using PoE.

Switch to Hub or Switch

Connect the switch to another switch or hub using

the RJ-45 or SFP uplink ports.

Switch to Server

Connect the switch to a network backbone or

network server using the RJ-45 or SFP uplink ports.

Additional Information

For additional support, please refer to the user

manual, or visit http://support.dlink.com/ which

will direct you to your local D-Link support website.

Ver. 1.01(WW)_130x183

2019/12/26

Andere Handbücher für DSS-100E-18P

Inhaltsverzeichnis

Andere D-Link Schalten Handbücher

D-Link

D-Link Nuclias DNH-100 Bedienungsanleitung

D-Link

D-Link GO-SW-8G Bedienungsanleitung

D-Link

D-Link DWS-1008 Bedienungsanleitung

D-Link

D-Link DGS-3100 SERIES Bedienungsanleitung

D-Link

D-Link DGS-1008P Bedienungsanleitung

D-Link

D-Link DGS-3100 SERIES Bedienungsanleitung

D-Link

D-Link xStack DES-3810 Bedienungsanleitung

D-Link

D-Link DGS-1210-52MP Bedienungsanleitung

D-Link

D-Link DFE-2624 - Hub - Stackable Bedienungsanleitung

D-Link

D-Link DES-1210/ME Series Bedienungsanleitung

D-Link

D-Link DGS-105 - Switch Bedienungsanleitung

D-Link

D-Link DES-7000 Series Bedienungsanleitung

D-Link

D-Link DGS-3024 Bedienungsanleitung

D-Link

D-Link DES-3226 Bedienungsanleitung

D-Link

D-Link DGS-3100 SERIES Bedienungsanleitung

D-Link

D-Link DKVM-440 Bedienungsanleitung

D-Link

D-Link DGS-1210/ME series Handbuch

D-Link

D-Link SmartPro DGS-1500-20 Bedienungsanleitung

D-Link

D-Link DUB-H4 - Hub - USB Bedienungsanleitung

D-Link

D-Link DGS-1100-10MP Bedienungsanleitung

D-Link

D-Link DGS-3120-24PC-SI Handbuch

D-Link

D-Link DGS-1008MP Bedienungsanleitung

D-Link

D-Link DES-2108 Bedienungsanleitung

D-Link

D-Link DGS-1216T - Switch Bedienerhandbuch

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung