Dürkopp Adler 867 Betriebsanleitung
867
Additional Instructions
Puller Feed Drive
All rights reserved.
Property of Dürkopp Adler AG and protected by copyright. Any reuse of these contents, includ-
ing extracts, is prohibited without the prior written approval of Dürkopp Adler AG.
Copyright © Dürkopp Adler AG 2016
IMPORTANT
READ CAREFULLY BEFORE USE
KEEP FOR FUTURE REFERENCE
Table of Contents
Additional Instructions 867 - 02.0 - 12/2016 1
1 About this additional manual ....................................................3
2 Machine overview.......................................................................4
3 Operation.....................................................................................5
3.1 Activating the puller feed drive .....................................................5
3.2 Setting the top puller pressure......................................................6
4 Settings .......................................................................................7
4.1 Setting the feed distance..............................................................7
4.2 Setting the puller feed type...........................................................7
4.3 Setting the puller feed operating mode.........................................8
4.4 Setting the puller delay.................................................................8
4.5 Setting the angle of feed...............................................................8
4.6 Setting the material compensation values....................................8
5 Service.........................................................................................9
5.1 Initializing the puller feed drive.....................................................9
5.2 Setting other parameters..............................................................9
5.2.1 Setting the transmission ratios .....................................................9
5.2.2 Setting the puller feed pressure....................................................9
5.2.3 Setting puller feed operation.......................................................10
5.3 Malfunctions ...............................................................................10
6 Appendix ...................................................................................11
Table of Contents
2Additional Instructions 867 - 02.0 - 12/2016
About this additional manual
Additional Instructions 867 - 02.0 - 12/2016 3
1 About this additional manual
This additional manual describes the puller feed drive with DAC control.
For the standard functions, see the DAC Control Operating Manual.
Kits:
0867 591134
0867 591144
Machine overview
4Additional Instructions 867 - 02.0 - 12/2016
2 Machine overview
Fig. 1: Machine overview
(1) - Control panel
(2) - Top puller pressure regulator (3) - Puller feed drive button
(4) - Top puller
①
②
③
④
Operation
Additional Instructions 867 - 02.0 - 12/2016 5
3 Operation
3.1 Activating the puller feed drive
Fig. 2: Activating the puller feed drive
1. Activate the puller feed drive (1) switch on the control unit.
Leave the switch activated permanently.
2. Switch on the machine at the main switch (2).
3. Press the puller feed drive (3) button on the machine's arm.
The button lights up, the puller feed drive is activated.
(1) - Puller feed drive switch
(2) - Main switch (3) - Puller feed drive button
①② ③
Operation
6Additional Instructions 867 - 02.0 - 12/2016
3.2 Setting the top puller pressure
The pressure of the top puller can be set when the puller feed drive is ac-
tivated.
Fig. 3: Setting the top puller pressure
1. Activate the puller feed drive.
2. Pull the adjustment knob (1) up.
3. Turn the adjustment knob and set the pressure (0 - 6 bar):
•clockwise: to increase pressure
•counterclockwise: to reduce pressure
4. Push the adjustment knob (1) down.
(1) - Adjustment knob (2) - Pressure gauge
①
②
Settings
Additional Instructions 867 - 02.0 - 12/2016 7
4 Settings
Fig. 4: Settingsn
4.1 Setting the feed distance
The feed distance can be set between a length of 1 – 15 mm per stitch in
increments of 1/10.
1. Tochangethefeeddistanceofthetoppuller,pressthePlus/Minus (D)
buttons.
2. To change the feed distance of the bottom puller, press the Plus/
Minus (B) buttons.
4.2 Setting the puller feed type
Two types of feed are available: Constant or intermittent feed. With inter-
mittent feed, the speed is restricted and depends on the feed distance set.
1. Open the parameter t 14 11.
2. Set the feed height:
• 0: constant
• 1: intermittent
Information
To change quickly between the feed types, the puller feed type can be pro-
grammed to the freely programmable F-key on the control panel (parame-
ter t 52 20 = 23).
See also DAC Control operating manual.
(1) - Gauge A (Stitch length)
(2) - ESC key
(3) - F-key
(4) - Plus-/minus buttons forbottom
puller (B)
(5) - Plus-/minus buttons for top puller (D)
(6) - OK button
ESC
ABCD
OK
++++
––––
PRESET
⑥
①
②
③
④⑤
Settings
8Additional Instructions 867 - 02.0 - 12/2016
4.3 Setting the puller feed operating mode
You can set when the puller should lift up automatically.
1. Open the parameter t 14 00.
2. Set the operating mode:
• 0: Puller is not lifted up
• 1: Puller is lifted up with sewing foot aeration
• 2: Puller is lifted with bar
• 3: Puller is lifted with sewing foot aeration and bar
4.4 Setting the puller delay
You can set the number of stitches until the puller is lowered.
1. Open the parameter t 14 03.
2. Set the number of stitches (0-255).
The puller feed button lights up, the puller feed drive is activated.
4.5 Setting the angle of feed
You can set the angle at which the puller is to feed.
0° is the reference position here.
The default settings are:
• 10° for the initial feed angle
• 170° for the final feed angle
1. Open the parameter t 14 12.
2. Set the initial feed angle (0-359°).
3. Open the parameter t 14 13.
4. Set the final feed angle (0-359°).
4.6 Setting the material compensation values
Slip properties of various materials can be compensated for.
1. Set a stitch length of 5 mm.
2. Open the parameter t 14 21.
3. Set the material compensation value for the top feed puller (0-255).
4. Open the parameter t 14 31.
5. Setthematerialcompensationvalueforthebottomfeedpuller(0-255).
Andere Handbücher für 867
19
Inhaltsverzeichnis
Andere Dürkopp Adler Nähmaschine Handbücher
Dürkopp Adler
Dürkopp Adler 204 Bedienungsanleitung
Dürkopp Adler
Dürkopp Adler 868 Bedienungsanleitung
Dürkopp Adler
Dürkopp Adler 550-D800 Bedienungsanleitung
Dürkopp Adler
Dürkopp Adler M-Type 869 Bedienungsanleitung
Dürkopp Adler
Dürkopp Adler 878-M PREMIUM Bedienungsanleitung
Dürkopp Adler
Dürkopp Adler 52Xi Betriebsanleitung
Dürkopp Adler
Dürkopp Adler M-Type 838-180122-M Betriebsanleitung
Dürkopp Adler
Dürkopp Adler D869 e-con Betriebsanleitung
Dürkopp Adler
Dürkopp Adler 550-867 Bedienungsanleitung
Dürkopp Adler
Dürkopp Adler 195 Betriebsanleitung
Dürkopp Adler
Dürkopp Adler 867 Betriebsanleitung
Dürkopp Adler
Dürkopp Adler 767 - Bedienungsanleitung
Dürkopp Adler
Dürkopp Adler 650-16 Bedienungsanleitung
Dürkopp Adler
Dürkopp Adler DAC classic 271 Bedienungsanleitung
Dürkopp Adler
Dürkopp Adler 513 Bedienungsanleitung
Dürkopp Adler
Dürkopp Adler 559 - Bedienungsanleitung
Dürkopp Adler
Dürkopp Adler M-TYPE 667 Bedienungsanleitung
Dürkopp Adler
Dürkopp Adler 1767 Bedienungsanleitung
Dürkopp Adler
Dürkopp Adler 867 Betriebsanleitung
Dürkopp Adler
Dürkopp Adler 888 Bedienungsanleitung
