Dacor DISCOVERY DYF48BNDI Technisches Handbuch

All specications subject to change without notice. Phone: (800) 793-0093www.dacor.com

PLANNING

GUIDE

DYF42BNDI, DYF48BNDI

Discovery™42” and 48” Wide

Built-In Custom Panel Refrigerators

Document # PG11-013 Revised 02/04/13 Page 1/5

83¹/2"(212.1 cm) min.

84³/4"(215.3 cm) max.

to bottom of solid soffit

77"

(195.6 cm)

(see chart following)

24"

(61.0 cm) Min.

Model Series Cutout Width A Dimension B

DYF42BNDI 41½” (105.4 cm) to

41¾” (106.0 cm)

10”

(25.4 cm)

DYF48BNDI 47½” (120.7 cm) to

47¾” (121.3 cm)

16”

(40.6 cm)

NOTE: Flooring under refrigerator must be at same level as the room. Face

of cabinetwork must be plumb.

See Page 2/5

WARNING

• Observe all governing codes and ordinances during planning

and installation. Contact your local building department for

further information.

• This appliance must be installed in accordance with the

accompanying installation instructions.

Location Requirements

Your Dacor refrigerator can be recessed in an opening between cabinets

or installed at the end of a cabinet run using a side panel to enclose the

refrigerator.

IMPORTANT:

◊ The location must allow the refrigerator to be moved out from the

wall without being disconnected in the event that service become

necessary.

◊ It is recommended that you do not install the refrigerator near an

oven, radiator, or other heat source.

◊ Do not install in a location where the temperature will fall below 55°F

(13°C).

◊ Floor must support the refrigerator weight, more than 600 lbs.

(272 kg), door panels and contents of the refrigerator.

◊ Ceiling height must allow for side tipping radius. See installation

instructions.

◊ Location should permit doors to open fully. See Door Swing

Dimensions.

◊ Location must permit top grille removal. See Opening Dimensions.

◊ A grounded 3 prong electrical outlet should be placed in the area

shown in the diagram on the right. See Electrical Requirements for

more information.

◊ The water shutoff should be located in the base cabinet on either

side of the refrigerator or some other easily accessible area. If the

water shutoff valve is not in the cabinets, the plumbing for the water

line can come through the floor or the back wall. See Water Supply

Requirements for more information.

Opening Dimensions

◊ To avoid tipping during use, the solid soffit must be within 1” (2.5 cm)

maximum above the refrigerator. If the solid soffit is higher than 1”

(2.5 cm) or one is not available, then the refrigerator must be braced.

If the anti-tip boards are needed, they must be attached to the rear

wall studs 80” to 90” (203.2 cm to 228.6 cm) above the floor. See

installation instructions for more information.

NOTE:Aclearanceof¹⁄2” (1.3 cm) must be maintained above the top

grille in order for the top grille to be removed.

1/2” (1.3 cm)

All specications subject to change without notice. Phone: (800) 793-0093www.dacor.com

PLANNING

GUIDE

DYF42BNDI, DYF48BNDI

Discovery 42” and 48” Wide

Built-In Custom Panel Refrigerators

Document # PG11-013 Revised 02/04/13 Page 2/5

Electrical Requirements

The electrical circuit must meet all local codes and ordinances.

Recommended Grounding Method

A 115 Vac, 60 Hz., 15 or 20 Amp. fused, grounded electrical supply is

required. It is recommended that a separate circuit serving only your

refrigerator be provided. Use an outlet that cannot be turned off by a switch.

Do not use an extension cord.

IMPORTANT: If this product is connected to a GFCI (Ground Fault Circuit

Interrupter) protected outlet, nuisance tripping of the power supply may

occur, resulting in loss of cooling. Food quality and flavor may be affected.

Water Supply Requirements

◊ The water shutoff should be located in the base cabinet

on either side of the refrigerator or some other easily

accessible area. The right-hand side is recommended.

NOTE: If the water shut off valve is in the back wall behind the

refrigerator, it must be at an angle so that the tube is not kinked

when the refrigerator is pushed into its final position.

◊ If the water shutoff valve is not in the cabinets, the

plumbing for the water line can come through the floor. A

½” (1.3 cm) hole for plumbing should be drilled at least 6”

(15.2 cm) from the right or left hand side cabinet or panel.

On the floor, the hole should be no more than 1”

(2.5 cm) away from the back wall.

◊ Your refrigerator dealer has a kit available with a ¼” (6.4

mm) saddle-type shutoff valve. Before purchasing, make

sure a saddle-type valve complies with your local plumbing

codes.

◊ Donotuseapiercing-typeor³⁄16” (4.8 mm) saddle valve

which reduces water flow and clogs more easily.

◊ Install the water supply line only in areas where the

household temperatures will remain above freezing.

Water Pressure

A cold water supply with water pressure between 30 and 120 psi (207 and

827 kPa) is required to operate the water dispenser and ice maker.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a reverse

osmosis system going to the water inlet valve of the refrigerator needs to

be between 30 and 120 psi (207 and 827 kPa). If a reverse osmosis water

filtration system is connected to your cold water supply, the water pressure

to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276

to 414 kPa).

Possible water

line locations

1” x 1”

(2.5 cm x 2.5 cm)

(2.5cm)

(15.2 cm)

All specications subject to change without notice. Phone: (800) 793-0093www.dacor.com

PLANNING

GUIDE

DYF42BNDI, DYF48BNDI

Discovery 42” and 48” Wide

Built-In Custom Panel Refrigerators

Document # PG11-013 Revised 02/04/13 Page 3/5

NOTE: Additional space may be required depending on the overlay panel

thickness (see below).

To adjust the door swing, see the installation instructions.

Allow a minimum of 4½” (11.4 cm) of space between the side of the

refrigerator and a corner wall. More clearance may be needed if thicker

custom panels or custom handles are used. Do not overlook baseboards.

Refrigerator to

Cabinet Clearance

Door Swing 90°

Door Panels and Cabinetry Clearance - Door Swing 110°

The custom door panels and adjacent cabinetry must be designed so that

there is sufficient clearance for the doors to swing open. If the refrigerator is

to be installed close to the wall, see Door Swing 90°.

Door Swing Dimensions

The location must permit both doors to open to a minimum of 90°. Allow

4½” (11.4 cm) minimum space between the side of the refrigerator and a

corner wall.

Model DYF42BNDI

130˚

90˚

110˚

477⁄8"

(121.6 cm)

411⁄2"

(105.4 cm)

167⁄8"

(42.9 cm)

12 5⁄8"

(32.1 cm)

371⁄4"

(94.6 cm)

413⁄8"

(105.1 cm)

130˚

90˚

110˚

513⁄8"

(130.5 cm)

44"

(111.8 cm)

191⁄4"

(48.9 cm)

143

⁄

(36.5 cm)

39"

(99.1 cm)

437⁄8"

(111.4 cm)

Model DYF48BNDI

Spacer Panel

¼" (6.35 mm)

¾" (1.9 cm)

1" (2.5 cm)

½" (1.3 cm)

1 ¼"

1 ½"

(2.5 cm)

1 ¼

(3.2 cm)

1½

(3.8cm)

Refrigerator

Side Trim

Door

Hinge

Backer Panel

Overlay Panel

(2.5 cm)

(3.2 cm)

(3.8 cm)

(1.3 cm)

Cabinetry

(1.9 cm)

½"

¾"

When the doors are closed the

refrigerator will extend beyond

the face of the adjacent cabinets

to some degree.

NOTE: Rout the hinge side

of the custom door panels to

a radius that is equal to at

least half the thickness of the

panel if a 130° door swing is

desired. See the installation

instructions.

Refrigerator to

Cabinet Clearance

Door Swing 110°

Refrigerator

Side Trim

Door

Backer Panel

Overlay Panel

Hinge

Spacer Panel

Cabinetry

90˚ Door

Stop Position

¼" (6.35 mm)

¾" (1.9 cm)

¾"

(1.9 cm)

1" (2.5 cm)

½" (1.3 cm)

½"

(1.3 cm)

(2.5 cm)

1 ¼

(3.2 cm)

1½

(3.8cm)

(1.3 cm)

(1.9 cm)

½"

¾"

All specications subject to change without notice. Phone: (800) 793-0093www.dacor.com

PLANNING

GUIDE

DYF42BNDI, DYF48BNDI

Discovery 42” and 48” Wide

Built-In Custom Panel Refrigerators

Document # PG11-013 Revised 02/04/13 Page 4/5

Custom Panels

The custom overlay panels allow you to blend the exterior of your

refrigerator into the overall kitchen décor, and to use custom handles for

additional design flexibility. The custom panels must have backer panels

attached in order to mount them to the refrigerator. It is most common to

work with three panels, as shown in the graphic on the right. A decorative

overlay panel, a ¹/8” (3.2 mm) spacer panel or spacer strips and a ¼” (6.4

mm) backer panel.

In some cases, your cabinet manufacturer may choose to work with one

panel routed for the different dimensions. Follow these panel dimension

and placement instructions to be sure that the custom overlay panels will fit

properly.

Overlay panel

Spacer panel

Backer panel

Door

5/8"to 3/4"

(1.6 to 1.9 cm) 1/8"

(3.2 mm)

1/4"

(6.4 mm)

1" Min.

(2.5 cm)

Trim frame

Spacer panel

Offset dimension

1/8"

(3.2 mm)

IMPORTANT: Install the panels after moving the refrigerator into place.

The weight of the overlay panels cannot exceed:

50 lbs (22.7 kg) for the refrigerator door.

40 lbs. (18.1 kg) for the freezer door.

10 lbs (4.5 kg) for the top grille.

To minimize panel weight, you may use 2” (5.1 cm) spacer strips around

the perimeter in place of full-sheet solid spacer panels. The spacer strips

must be set in at least 1” (2.5 cm) from the top, bottom and sides edges of

the backer panel. If you use spacer strips, it is also recommended that you

use two 2” (5.1 cm) strips horizontally centered for added support.

Decorative Overlay Panels

Series A B C

DYF42 17¼” (43.8 cm) 23¼” (59.1 cm) 40¾” (103.5 cm)

DYF48 19¾” (50.2 cm) 26¾” (68.0 cm) 46¾” (118.8 cm)

Backer Panels

Series D E F

DYF42 16¾” (42.6 cm) 22¾” (57.8 cm) 40¾” (101.0 cm)

DYF48 19¼” (48.9 cm) 26¼” (66.7 cm) 46¾” (116.2 cm)

G- Denotes top and bottom edges of backer panel that slide into

trim frame on door and top grille.

¹⁄2

(179.1 cm)

¹⁄2

(179.1 cm)

Refrigerator panel

Freezer panel

handle-side

Backer

offset

¹⁄8

" (3.2 mm)

¹⁄8

"(3.2 mm) Backer bottom offset

¹⁄8

"(3.2 mm)

bottom offset

Backer

Backer panel

Overlay panel

(183.5 cm)

72¼

Top grille

(15.7 cm)

(18.4 cm)

offset

side

Backer

½"

(1.3 cm)

Backer bottom offset

½"(1.3 cm)

All specications subject to change without notice. Phone: (800) 793-0093www.dacor.com

PLANNING

GUIDE

Inset Installation Dimensions

■Measure the distance from point A

(as shown) to the back wall. Add

¹⁄32” (0.8 mm) to this measurement

to allow the side panel to fit into the

trim.

■ Ifthepanelismorethan³⁄8” (9.5

mm) thick, rout the front edge to

allow the side panel to fit into the

trim.

Recessed Inset Installation Dimensions

■Measure the distance

from point B (as

shown) to back wall.

■Route the front edge

of the support board

orattacha³⁄8” (9.5

mm) board to hold the

panel in the cabinet

side trim.

DYF42BNDI, DYF48BNDI

Discovery 42” and 48” Wide

Built-In Custom Panel Refrigerators

Document # PG11-013 Revised 02/04/13 Page 5/5

Custom Handle Dimensions and Installation

◊ Before installing a custom panel

assembly, you must install the

custom handle hardware. The

handle and handle mounting

hardware are not provided with the

refrigerator.

◊ Dacor recommends handles with

larger D-style pulls. Any handle

designed for use with an appliance

should produce satisfactory

results. Handle kits are available

through your Dacor dealer.

◊ Handle kits do not include the

necessary mounting screws

since screw length required

varies with the total thickness of

the panels. The panel craftsman

must determine and obtain the

proper mounting screws for

the application. If using screws

with thick heads, they must be

countersunk into the panel before

installing the handles.

IMPORTANT: Dacor does not advise

the use of single pull knobs.

Custom Side Panels

Custom side panels may be needed when not enough space is available

to have cabinets on both sides of the refrigerator or when the refrigerator is

placed at the end of a cabinet run.

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type of

installation you are planning.

NOTES:

■The dimensions shown are actual product dimensions and may not

reflect the needed installation dimensions.

■The side panel should be a

minimum of ½” (1.3 cm) thick to

avoid warping.

■If the opening depth is 25” (63.5

cm) or more, you may want to

install a support board on rear

wall.

11⁄16"

(60.2 cm)

3⁄8

"(9.7 mm)

1⁄16

"(1.5 mm)

3⁄32

"(2.4 mm)

3⁄16

(4.8 mm)

Back wall

A. Countersunk screw

Trim frame

surrounding door

B. Handle

C. Door panel assembly

Door

20" Typ.

(50.8 cm)

36" Max.

(91.4 cm)

REFRIGERATOR SIDE TRIM

Andere Handbücher für DISCOVERY DYF48BNDI

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dacor Kühlschrank Handbücher

Dacor

Dacor EF36 Bedienungsanleitung

Dacor

Dacor IF36BNDF Bedienungsanleitung

Dacor

Dacor EF36IWF Bedienungsanleitung

Dacor

Dacor Millennia AFM36VSP Technisches Handbuch

Dacor

Dacor EF42DBSS Bedienungsanleitung

Dacor

Dacor Millennia AFM36VSP Bedienungsanleitung

Dacor

Dacor IF36BNDFSF Bedienungsanleitung

Dacor

Dacor RF36NDFSS Bedienungsanleitung

Dacor

Dacor DYF42BIWS Bedienungsanleitung

Dacor

Dacor DISCOVERY DYF48BNDI Bedienungsanleitung

Dacor

Dacor DTF36FCS Fehlerbehebungshandbuch

Dacor

Dacor Epicure EF36LNDFSS Technisches Handbuch

Dacor

Dacor EF36LNBSS Bedienungsanleitung

Dacor

Dacor IF36BNNFSF Montageanleitung

Dacor

Dacor EF36BNF Series Bedienungsanleitung

Dacor

Dacor DYF42SBI Series Bedienungsanleitung

Dacor

Dacor DRF365 Series Bedienungsanleitung

Dacor

Dacor EF36LNFSS Bedienungsanleitung

Dacor

Dacor EF36BNNFSS Bedienungsanleitung

Dacor

Dacor DISCOVERY DYF42BNDI Bedienungsanleitung

Dacor

Dacor DRF36C000SR Bedienungsanleitung

Dacor

Dacor EF36IWF Montageanleitung

Dacor

Dacor Discovery DYF42BSIWS Bedienungsanleitung

Dacor

Dacor EF36BNNF Series Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung