Dahua Technology IPC-HFW3841E-AS-0280B-S2 Bedienungsanleitung

HD IR Bullet Network Camera

Quick Start Guide

V1.0.2ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD.

Quick Start Guide

Foreword

General

This manual introduces the installation and operations of network camera. Read carefully before using

the device, and keep the manual safe for future reference.

Safety Instructions

The following signal words might appear in the manual.

Signal Words Meaning

Indicates a medium or low potential hazard which, if not avoided,

could result in slight or moderate injury.

Indicates a potential risk which, if not avoided, may result in

property damage, data loss, reductions in performance, or

unpredictable result.

Provides additional information as a supplement to the text.

Revision History

Version Revision Content Release Date

V1.0.2 Updated the information of installing the camera. August 2022

V1.0.1 Updated "Important Safeguards and Warnings." April 2021

V1.0.0 First release. May 2019

Privacy Protection Notice

As the device user or data controller, you might collect the personal data of others such as their face,

fingerprints, and license plate number. You need to be in compliance with your local privacy protection

laws and regulations to protect the legitimate rights and interests of other people by implementing

measures which include but are not limited: Providing clear and visible identification to inform people

of the existence of the surveillance area and provide required contact information.

About the Manual

The manual is for reference only. Slight differences might be found between the manual and the

product.

We are not liable for losses incurred due to operating of the product in ways that are not in

compliance with the manual.

The manual will be updated according to the latest laws and regulations of related jurisdictions.

For detailed information, see the paper User Manual, use our CD-ROM, scan the QR code or visit

Quick Start Guide

our official website. The manual is for reference only. Slight differences might be found between

the electronic version and the paper version.

All the designs and software are subject to change without prior written notice. Product updates

might result in some differences appearing between the actual product and the manual. Please

contact customer service for the latest program and supplementary documentation.

There might be deviations in the description of the technical data, functions and operations, or

errors in the print. If there is any doubt or dispute, we reserve the right of final explanation.

Upgrade the reader software or try other mainstream reader software if the manual (in PDF

format) cannot be opened.

All trademarks, registered trademarks and the company names in the manual are the properties

of their respective owners.

Please visit our website, contact the supplier or customer service if any problems occur while

using the device.

If there is any uncertainty or controversy, we reserve the right of final explanation.

Quick Start Guide

III

Important Safeguards and Warnings

This section introduces content covering the proper handling of the device, hazard prevention, and

prevention of property damage. Read carefully before using the device, comply with the guidelines

when using it.

Transportation Requirements

Transport the device under allowed humidity and temperature conditions.

Pack the device with packaging provided by its manufacturer or packaging of the same quality

before transporting it.

Do not place heavy stress on the device, violently vibrate or immerse it in liquid during

transportation.

Storage Requirements

Store the device under allowed humidity and temperature conditions.

Do not place the device in a humid, dusty, extremely hot or cold site that has strong

electromagnetic radiation or unstable illumination.

Do not place heavy stress on the device, violently vibrate or immerse it in liquid during storage.

Installation Requirements

Strictly comply with the local electrical safety code and standards, and check whether the power

supply is correct before operating the device.

Please follow the electrical requirements to power the device.

When selecting the power adapter, the power supply must conform to the requirements of

ES1 in IEC 62368-1 standard and be no higher than PS2. Please note that the power supply

requirements are subject to the device label.

We recommend using the power adapter provided with the device.

Do not connect the device to two or more kinds of power supplies, unless otherwise specified, to

avoid damage to the device.

The device must be installed in a location that only professionals can access, to avoid the risk of

non-professionals becoming injured from accessing the area while the device is working.

Professionals must have full knowledge of the safeguards and warnings of using the device.

Quick Start Guide

Do not place heavy stress on the device, violently vibrate or immerse it in liquid during installation.

An emergency disconnect device must be installed during installation and wiring at a readily

accessible location for emergency power cut-off.

We recommend you use the device with a lightning protection device for stronger protection

against lightning. For outdoor scenarios, strictly comply with the lightning protection regulations.

Ground the function earthing portion of the device to improve its reliability (certain models

are not equipped with earthing holes). The device is a class I electrical appliance. Make sure that

the power supply of the device is connected to a power socket with protective earthing.

The dome cover is an optical component. Do not directly touch or wipe the surface of the cover

during installation.

Operation Requirements

The cover must not be opened while the device is powered on.

Do not touch the heat dissipation component of the device to avoid the risk of getting burnt.

Use the device under allowed humidity and temperature conditions.

Do not aim the device at strong light sources (such as lamplight, and sunlight) when focusing it,

to avoid reducing the lifespan of the CMOS sensor, and causing overbrightness and flickering.

When using a laser beam device, avoid exposing the device surface to laser beam radiation.

Prevent liquid from flowing into the device to avoid damage to its internal components.

Protect indoor devices from rain and dampness to avoid electric shocks and fires breaking out.

Do not block the ventilation opening near the device to avoid heat accumulation.

Protect the line cord and wires from being walked on or squeezed particularly at plugs, power

sockets, and the point where they exit from the device.

Do not directly touch the photosensitive CMOS. Use an air blower to clean the dust or dirt on the

lens.

The dome cover is an optical component. Do not directly touch or wipe the surface of the cover

when using it.

There might be a risk of electrostatic discharge on the dome cover. Power off the device when

installing the cover after the camera finishes adjustment. Do not directly touch the cover and

make sure the cover is not exposed to other equipment or human bodies

Strengthen the protection of the network, device data and personal information. All necessary

safety measures to ensure the network security of the device must be taken, such as using strong

passwords, regularly changing your password, updating firmware to the latest version, and

isolating computer networks. For the IPC firmware of some previous versions, the ONVIF

password will not be automatically synchronized after the main password of the system has been

changed. You need to update the firmware or change the password manually.

Quick Start Guide

Maintenance Requirements

Strictly follow the instructions to disassemble the device. Non-professionals dismantling the

device can result in it leaking water or producing poor quality images. For a device that is required

to be disassembled before use, make sure the seal ring is flat and in the seal groove when putting

the cover back on. When you find condensed water forming on the lens or the desiccant becomes

green after you disassembled the device, contact after-sales service to replace the desiccant.

Desiccants might not be provided depending on the actual model.

Use the accessories suggested by the manufacturer. Installation and maintenance must be

performed by qualified professionals.

Do not directly touch the photosensitive CMOS. Use an air blower to clean the dust or dirt on the

lens. When it is necessary to clean the device, slightly wet a soft cloth with alcohol, and gently

wipe away the dirt.

Clean the device body with a soft dry cloth. If there are any stubborn stains, clean them away with

a soft cloth dipped in a neutral detergent, and then wipe the surface dry. Do not use volatile

solvents such as ethyl alcohol, benzene, diluent, or abrasive detergents on the device to avoid

damaging the coating and degrading the performance of the device.

The dome cover is an optical component. When it is contaminated with dust, grease, or

fingerprints, use degreasing cotton moistened with a little ether or a clean soft cloth dipped in

water to gently wipe it clean. An air gun is useful for blowing dust away.

It is normal for a camera made of stainless steel to develop rust on its surface after being used in

a strong corrosive environment (such as the seaside, and chemical plants). Use an abrasive soft

cloth moistened with a little acid solution (vinegar is recommended) to gently wipe it away.

Afterwards, wipe it dry.

Quick Start Guide

Table of Contents

Foreword............................................................................................................................................................ I

Important Safeguards and Warnings............................................................................................................. III

1 Introduction................................................................................................................................................... 1

Cable ............................................................................................................................................................................................... 1

Connecting Alarm Input/output .......................................................................................................................................... 2

2 Network Configuration ................................................................................................................................. 4

Initializing the Camera ............................................................................................................................................................. 4

Changing the Device IP Address .......................................................................................................................................... 5

Logging in to Webpage ........................................................................................................................................................... 5

3 Installation..................................................................................................................................................... 6

Packing List................................................................................................................................................................................... 6

Dimensions................................................................................................................................................................................... 6

Installing Device ......................................................................................................................................................................... 7

3.3.1 Installation Methods.................................................................................................................................................... 7

3.3.2 (Optional) Installing the SD Card ............................................................................................................................ 7

3.3.3 Attaching the Camera................................................................................................................................................. 7

3.3.4 (Optional) Installing the Waterproof Connector ............................................................................................... 8

3.3.5 Adjusting the Lens Angle........................................................................................................................................... 9

Quick Start Guide

1Introduction

Cable

Waterproof all the cable joints with insulating tape and waterproof tape to avoid water damage and

prevent short circuits from occurring. For details, see FAQ manual.

Cables

Table 1-1 Cable information

Port Port Name Description

1 Power input

Inputs 12 VDC power. Please be sure to supply power as instructed in the

Guide.

Device abnormity or damage could occur if power is not supplied

correctly.

2 Ethernet

Connects to network with network cable.

Provides power to the device with PoE.

PoE is available on select models.

3 Alarm I/O Includes alarm signal input and output ports. For detailed information,

see Table 1-2.

4 Audio input Connects to sound-pick-up device to receive audio signal.

5 Audio output Connects to speaker to output audio signal.

Table 1-2 Alarm information

Port Port Name Description

Alarm I/O

ALARM_OUT Outputs alarm signal to alarm device.

ALARM_IN Receives the switch signal of external alarm source.

ALARM_GND Ground connection.

Quick Start Guide

Connecting Alarm Input/output

Alarm input/output is available on select models.

Connect alarm input device to the alarm input end of the I/O port.

Device collects different states of alarm input port when the input signal is idling and being

grounded.

Device collects logic "1" when input signal is connecting to +3 V to +5 V or idling.

Device collects logic "0" when input signal is grounded.

Alarm input

Connect alarm output device to the alarm output end of the I/O port. The alarm output is

open-drain output, which works in the following modes.

Mode A: Level application. Alarm outputs high and low level, and the alarm outlet is OD,

which requires external pull-up resistance (10 K Ohm typical) to work. The maximum

external pull-up level is 12 V, maximum port current is 300 mA and the default output

signal is high level (external pull-up voltage). The default output signal switches to low

level when there is alarm output (As long as the operating current below 300 mA, the

output low level voltage is lower than 0.8 V).

Mode B: Switch application. Alarm output is used to drive external circuit, the maximum

voltage is 12 V and the maximum current is 300 mA. If the voltage is higher than 12 V,

please use an additional electric relay.

Mode A

Quick Start Guide

Mode B

The alarm input in the webpage is corresponding to the alarm input end of the I/O port.

There will be high level and low level alarm signal generated by the alarm input device

when alarm occurs, set the input mode to "NO" (default) if the alarm input signal is logic

"0" and to "NC" if the alarm input signal is logic "1".

The alarm output in the webpage is corresponding to the alarm output end of the device,

which is also alarm output end of the I/O port.

Inhaltsverzeichnis

Andere Dahua Technology Sicherheitskamera Handbücher

Dahua Technology

Dahua Technology IPC-HFW1230S1-0280B-S5 Bedienungsanleitung

Dahua Technology

Dahua Technology 8A840WANF Bedienungsanleitung

Dahua Technology

Dahua Technology IPC-MBW4231-AS/M12 Bedienungsanleitung

Dahua Technology

Dahua Technology DH-IPC-HDW1230T1P-S4 Bedienungsanleitung

Dahua Technology

Dahua Technology DH-IPC-HDBW3541FP-AS-M-0280B Bedienungsanleitung

Dahua Technology

Dahua Technology EOL Series Bedienungsanleitung

Dahua Technology

Dahua Technology 6CE230UNI Bedienungsanleitung

Dahua Technology

Dahua Technology DH-IPC-HFW4X-W Bedienungsanleitung

Dahua Technology

Dahua Technology IPC-HFW2849S-S-IL-0280B Bedienungsanleitung

Dahua Technology

Dahua Technology DH-IPC-HUM8441-E1-L4 Bedienungsanleitung

Dahua Technology

Dahua Technology D-IPC-HDBW3841EP-S-0280-S2 Bedienungsanleitung

Dahua Technology

Dahua Technology IPC-HDW1239DT-PV-STW Bedienungsanleitung

Dahua Technology

Dahua Technology DH-IPC-HFW3 Bedienungsanleitung

Dahua Technology

Dahua Technology IPC-HDW2249TM-S-IL-0280B Bedienungsanleitung

Dahua Technology

Dahua Technology DH-IPC-PFW83242-A180-S2 Bedienungsanleitung

Dahua Technology

Dahua Technology IPC-HFW5449T1-ASE-D2-0360B Bedienungsanleitung

Dahua Technology

Dahua Technology 50230UNI Bedienungsanleitung

Dahua Technology

Dahua Technology NAVIGATOR X1550 Bedienungsanleitung

Dahua Technology

Dahua Technology IPC-HDW5449H-ASE-D2-0280B Bedienungsanleitung

Dahua Technology

Dahua Technology HD IR Mini Bullet Bedienungsanleitung

Dahua Technology

Dahua Technology IR Eyeball Bedienungsanleitung

Dahua Technology

Dahua Technology IPC-HFW2531T-ZS-S2 Bedienungsanleitung

Dahua Technology

Dahua Technology DSS4004-S2 Allgemeine Anweisungen

Dahua Technology

Dahua Technology DH-HAC-HUM1220GN-B Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung