Dahua IPCHDBW3300N Bedienungsanleitung

HD IR Vandal Proof IP Dome Camera Quick Start Guide

Version 1.0

Welcome

Thank you for purchasing our IP camera!

This quick start guide is designed to be a reference tool for your system.

Please keep this start guide well for future reference.

Please open the accessory bag to check the items one by one in accordance with the list below.

Contact your local retailer ASAP if something is missing or damaged in the bag.

Before your operation please read the following instructions carefully.

1．Electrical safety

All installation and operation here should conform to your local electrical safety codes.

The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited

power source is rated 12V DC or 24V AC in the IEC60950-1.

We assume no liability or responsibility for all the fires or electrical shock caused by improper handling

or installation.

We are not liable for any problems caused by unauthorized modification or attempted repair.

2．Transportation security

Heavy stress, violent vibration or water splash are not allowed during transportation, storage and

installation.

3．Installation

Do not apply power to the camera before completing installation.

Please install the proper power cut-off device during the installation connection.

Always follow the instruction guide the manufacturer recommended.

4．Qualified engineers needed

All the examination and repair work should be done by the qualified service engineers.

We are not liable for any problems caused by unauthorized modifications or attempted repair.

5．Environment

This series IP camera should be installed in a cool, dry place away from direct sunlight, inflammable,

explosive substances and etc.

Please keep it away from the electromagnetic radiation object and environment.

Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.

Otherwise it may result in CCD (CMOS) optical component damage.

Please keep the sound ventilation.

Do not allow the water and other liquid falling into the camera.

6. Daily Maintenance

Please shut down the device and then unplug the power cable before you begin daily maintenance

work.

Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens

surface.

Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to

dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the

device.

Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.

7. Accessories

Be sure to use all the accessories recommended by manufacturer.

Before installation, please open the package and check all the components are included.

Contact your local retailer ASAP if something is broken in your package.

Accessory Name Amount

IPC Unit 1

MD9M data converter cable 1

Accessories bag 1

Quick Start Guide 1

Warranty Card 1

Certificate Card 1

CD 1

Table of Contents

1Framework...................................................................................................................................5

1.1 MD9M Data Converter Cable .....................................................................................5

1.2 Framework and Dimension.........................................................................................6

2Installation ...................................................................................................................................8

2.1 Device Installation ........................................................................................................8

2.2 SD Card Installation ...................................................................................................11

2.3 Lens Adjustment.........................................................................................................12

3Quick Configuration Tool.........................................................................................................13

3.1 Overview......................................................................................................................13

3.2 Operation .....................................................................................................................13

4Web Operation..........................................................................................................................16

4.1 Network Connection...................................................................................................16

4.2 Login and Logout........................................................................................................16

Appendix Toxic or Hazardous Materials or Elements ...............................................................19

1Framework

1.1 MD9M Data Converter Cable

You can refer to the following figure for MD9M data converter cable information. See Figure 1-1.

Figure 1-1

Please refer to the following sheet for detailed information.

Port Name Function Connection Note

VIDEO OUT Video output

port BNC Output analog video signal. It can connect to the

TV monitor to view the video.

AUDIO IN Audio input

port RCA Input audio signal. It can receive the analog audio

signal from the pickup.

AUDIO OUT Audio output

port RCA Output audio signal to the devices such as the

sound box.

12V DC/AC24V Power input

port / Power port. Input DC 12V/AC 24V

I/O I/O cable port / Connect to MD9M data converter cable.

LAN Network port Ethernet

port Connect to standard Ethernet cable.

Please refer to the follow sheet for detailed information of MD9M data converter cable.

Port Name Cable

Color Name Note

Yellow RS485_A RS485_A port. It is to control the PTZ.

Black RS485_B RS485_B port. It is to control the PTZ.

Red ALARM_COM Alarm output public port.

Brown ALARM_IN1 Alarm input port 1. It is to receive the on-off signal

from the external alarm source.

I/O Port

Grey ALARM_IN2

Alarm input port 2. It is to receive the on-off signal

from the external alarm source.

Port Name Cable

Color Name Note

White ALARM_NO

Alarm output port. It is to output the alarm signal

to the alarm device.

NO: normal open alarm output port.

It works with the ALARM_COM port.

Blue RESET

It is to restore factory default setup.

When the device is working properly, please

connect the blue cable (restore default setup port)

to the orange cable (GND signal) for 5 seconds,

the device can resume factory default setup.

Orange GND Ground port

1.2 Framework and Dimension

Please refer to the following figure for dimension information. The unit is mm. See Figure 1-2 and

Figure 1-3.

Figure 1-2

Figure 1-3

2Installation

This series IPC can be put on the table to realize surveillance. Or you can use the bracket or the

in-ceiling installation to realize the hang function. Please refer to the steps listed below.

2.1 Device Installation

Step 1

Use the inner hexagonal wrench (provided) to loose the three inner hexagon screws in the dome

cover and then open the cover. See Figure 2-1.

Figure 2-1

Step 2

Use the inner hexagonal wrench (provided) to loose the three inner hexagon screws in the dome

and then remove the device pedestal. See Figure 2-2.

Figure 2-2

Step 3

Draw out the cable exit and four screw holes in the installation position according to the device

pedestal. Dig the four plastic expansion bolt hole and cable exit. Insert the four plastic expansion

bolts into the screw holes

Step 4

Adjust the camera pedestal to the proper position and then draw the cable through the cable exit

you just dug in the ceiling (wall). Line up the four screw holes in the device pedestal to the four

plastic expansion bolt holes in the installation position. Put the four self-tapping screws in the

device pedestal and then use the screwdriver to secure the screws in the four plastic expansion

bolts firmly.

Step 5

Adjust the device position and line up the three inner hexagon screws of the device to the three

holes of the installation position. Put the three inner hexagon screws into the screw holes at the

bottom of the pedestal. Use the inner hexagon screwdriver to fix firmly. See Figure 2-3.

Figure 2-3

Step 6

Adjust the X-Y-Z axis module to turn the device to the proper monitor angle. Please follow the

steps listed below to adjust.

zSlightly loose the screws at the two sides of the X-Y-Z module manually, you can adjust the

module tilt rotation angle (15°～90°).

zSlightly loose the screw of the pressing slice, you can adjust the video rotation angle of the

module (0°～355°)

zAdjust the turning ring of the pedestal, you can adjust the module pan rotation angle (0°～

355°).

Please note, the screws in the following figure are the optical adjustment component.

Please make sure it is outward and do not allow it to touch the X-Y-Z axis module. See

Figure 2-4

Step 7

Put the dome cover back and then put the three inner hexagon screws into the holes of the

device. Use the inner hexagonal wrench to fasten these three screws. See Figure 2-5

Inhaltsverzeichnis

Andere Dahua Sicherheitskamera Handbücher

Dahua

Dahua N42AH3Z Bedienungsanleitung

Dahua

Dahua DH-SD6C430U-HNI Bedienungsanleitung

Dahua

Dahua HD Cube Network Camera Bedienungsanleitung

Dahua

Dahua HAC-HDBW2120EP Bedienungsanleitung

Dahua

Dahua EW5541-AS Bedienungsanleitung

Dahua

Dahua IPC-HUM8231-L3 Bedienungsanleitung

Dahua

Dahua IPC-C26EN Bedienungsanleitung

Dahua

Dahua NKB1000 Installations- und Benutzerhandbuch

Dahua

Dahua C series Bedienungsanleitung

Dahua

Dahua Panoramic Fisheye Bedienungsanleitung

Dahua

Dahua DH-IPC-WDX2 Bedienungsanleitung

Dahua

Dahua IPC-HFW1XXXS Bedienungsanleitung

Dahua

Dahua HDB4431C-AS Bedienungsanleitung

Dahua

Dahua IPC-HFW3849T1-AS-PV Bedienungsanleitung

Dahua

Dahua UAV-GA-V-2030U Bedienungsanleitung

Dahua

Dahua 49925TNI Bedienungsanleitung

Dahua

Dahua 42212TNI Bedienungsanleitung

Dahua

Dahua sd22204t-gn Bedienungsanleitung

Dahua

Dahua DH-SD49225I-HC-S3 Bedienungsanleitung

Dahua

Dahua SD59225I-HC Bedienungsanleitung

Dahua

Dahua DH-IPC-AX6 Bedienungsanleitung

Dahua

Dahua IPC-HFW2200R-VF Bedienungsanleitung

Dahua

Dahua F Series Bedienungsanleitung

Dahua

Dahua 6AE240VNI Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung