Dancing Wings DW DANCING POKE Bedienungsanleitung
DW DANCING POKE INSTRUCTION MANUAL
Low wing trainer airplane
EPP
DW Dancing Poke
Accessories include
A.Fuselage
B.Wing
C.Horizontal Tail
D.Vertical Tail
E.Front landing gear woods
E1.Front landing gear screws*2
F.Back landing gear woods
F1.Back landing gear screws*3
G.Wing �iberglass reinforcement*2
H.Back landing gear wheels
I.Front landing gear wheels*2
J.Front landing gear wheel cowling*2
K.Rubber band*4
L.Steel wire*4
M.Wooden pole*2
N.Paper hinge*2
O.Servo horn *4
P.Bonding compound
Q.Propeller
R.Y-wire
S.ESC20A
T.Servo 9g*4
U.Motor 2830 1150KV
U1.Motor screws
V.Prop adapter
STANDARD SETUP
Preparation Tool
Speci�ication
Wingspan: 1150mm
Length: 675mm
Flying Weight≈700-750g
Suggested Equipment
Motor：2830 1150KV
Propeller: 9-10inch
ESC: 20A
Servos：9g*4
Battery：3s 1500-2200mAh
Radio≥4CH
DW DANCING POKE INSTRUCTION MANUAL
How to Assemble
0.01 Apply the glue on the side of the wing, and join
together, and then insert the �iberglass reinforce-
ment into the slot on wing.
0.02 Assemble another wing by the same above way.
0.03 Insert the servo into the slot on the back of the
wing, meantime insert and glue the servo wire into
the wing, �inally pass through the middle of the wing.
0.04 Make a cut by knife in an upright position with
servo, insert the hinges and �ix by glue. Connect the
servo and servo horns on aileron by steel wire.
0.05 Assemble the 2pcs front landing gears as
picture shows below, �ix wheels with screws (E1)
,and paste the wheel cowling.
DW DANCING POKE INSTRUCTION MANUAL
0.06 Insert and glue the 2pcs landing gears into
slots as picture show.
0.07 Insert the horizontal tail into the rear of the
fuselage, and �ix by glue.
0.08 Apply the glue on the side of the vertical tail,
adjust and maintain the level with fuselage, �inally
join together by glue.
0.09 Glue the back landing gear parts and punch
holes on the wooden board as per the wheel screw
holes; �inally assemble the back landing gear.
0.10 Assemble the servos into the servo slots inside
the fuselage and �ix with screws.
0.11 Insert the servo steel wires into the slot on the
fuselage as picture shows below, one at either side
of the fuselage.
0.12 Con�irm the position of the steel wire comes
out, make cuts on the horizontal and vertical wing
by knife, insert the servo horns and �ix by glue.
DW DANCING POKE INSTRUCTION MANUAL
0.13 Connect the other end of the steel wire with
servos.horns.
0.14 Connect the motor and ESC together, assemble
the motor on the fuselage and �ix with screws (U1).
0.15 Assemble the propeller on the motor and �ix
with prop adapter.
0.16 Insert 2pcs wood poles on the each side of the
fuselage aim to �ix the wings.
0.17 Connect the wing and fuselage with rudder
band.
0.18 Assemble the battery, receiver, and adjust the
C.G, now you could try �lying.
Andere Dancing Wings Spielzeug Handbücher
Dancing Wings
Dancing Wings SCG42 Bedienungsanleitung
Dancing Wings
Dancing Wings DW DANCING PITTS Bedienungsanleitung
Dancing Wings
Dancing Wings DW PTERODACTYL Bedienungsanleitung
Dancing Wings
Dancing Wings LIGHTING EPP Bedienungsanleitung
Dancing Wings
Dancing Wings DW MINI EAGLE Bedienungsanleitung
Dancing Wings
Dancing Wings OLD FOGEY Bedienungsanleitung
