Danfoss VLT HVAC Basic Drive FC 101 Bedienungsanleitung

MAKING MODERN LIVING POSSIBLE

QQuick Guide

VLT® HVAC Basic Drive FC 101

www.danfoss.com/drives

*MG18A402*

132R0078 MG18A402 Rev. 2012-03-23

Contents

1 Quick Guide 2

1.1 Safety 2

1.1.1 Warnings 2

1.1.2 Safety Instructions 2

1.2 Introduction 3

1.2.1 Available Literature 3

1.2.2 Approvals 3

1.2.3 IT Mains 3

1.2.4 Avoid Unintended Start 4

1.2.5 Disposal Instruction 4

1.3 Installation 4

1.3.1 Before Starting Repair Work 4

1.3.2 Side-by-Side Installation 4

1.3.3 Dimensions 5

1.3.4 Electrical Installation in General 6

1.3.5 Connecting to Mains and Motor 7

1.3.6 Fuses 13

1.3.7 EMC-Correct Electrical Installation 15

1.3.8 Control Terminals 17

1.3.9 Electrical Overview 18

1.4 Programming 19

1.4.1 Programming with the Local Control Panel (LCP) 19

1.4.3 The Start-up Wizard for Open Loop Applications 20

1.5.1 Main menu structure 30

1.6 Warnings and Alarms 32

1.7 General Specifications 34

1.7.1 Mains Supply 3x200-240 V AC 34

1.7.2 Mains Supply 3x380-480 V AC 35

1.7.3 Mains Supply 3x380-480 V AC 37

1.7.4 Mains Supply 3x525-600 V AC 39

1.8 Special Conditions 43

1.8.1 Derating for Ambient Temperature and Switching Frequency 43

1.8.2 Derating for Low Air Pressure 43

1.9 Options for VLT®HVAC Basic Drive FC 101 43

1.10 MCT 10 Support 43

Contents VLT®HVAC Basic Drive Quick Guide

MG18A402 - VLT®is a registered Danfoss trademark 1

1 Quick Guide

1.1 Safety

1.1.1 Warnings

WARNING

High Voltage Warning

The voltage of the frequency converter is dangerous

whenever it is connected to mains. Incorrect installation of

the motor or frequency converter may cause damage to

the equipment, serious injury or death. Consequently, it is

essential to comply with the instructions in this manual as

well as local and national rules and safety regulations.

WARNING

DISCHARGE TIME!

Frequency converters contain DC-link capacitors that can

remain charged even when the frequency converter is not

powered. To avoid electrical hazards, disconnect AC mains,

any permanent magnet type motors, and any remote DC-

link power supplies, including battery backups, UPS and

DC-link connections to other frequency converters. Wait for

the capacitors to fully discharge before performing any

service or repair work. The amount of wait time is listed in

the Discharge Time table. Failure to wait the specified time

after power has been removed before doing service or

repair could result in death or serious injury.

Voltage [V] Power range [kW] Minimum waiting time

[min]

3x200 0.25–3.7 4

3x200 5.5–11 15

3x400 0.37–7.5 4

3x400 11–90 15

3x600 2.2–7.5 4

3x600 11–90 15

Table 1.1 Discharge Time

CAUTION

Leakage Current:

The earth leakage current from the frequency converter

exceeds 3.5 mA. According to IEC 61800-5-1 a reinforced

Protective Earth connection must be ensured with a min.

10 mm² Cu or an additional PE wire - with the same cable

cross section as the Mains wiring - must be terminated

separately.

Residual Current Device:

This product can cause a DC current in the protective

conductor. Where a residual current device (RCD) is used

for extra protection, only an RCD of Type B (time delayed)

shall be used on the supply side of this product. See also

Danfoss Application Note on RCD, MN90G.

Protective earthing of the frequency converter and the use

of RCDs must always follow national and local regulations.

Motor thermal protection:

Motor overload protection is possible by setting Parameter

1-90 Motor thermal protection to the value Electronic

Thermal Relay (ETR) trip.

WARNING

Installation at high altitudes

For altitudes above 2 km, contact Danfoss regarding PELV.

1.1.2 Safety Instructions

•Make sure the frequency converter is properly

connected to earth.

•Do not remove mains connections, motor

connections or other power connections while

the frequency converter is connected to power.

•Protect users against supply voltage.

•Protect the motor against overloading according

to national and local regulations.

•The earth leakage current exceeds 3.5 mA.

•The [Off/Reset] key is not a safety switch. It does

not disconnect the frequency converter from

mains.

Quick Guide VLT®HVAC Basic Drive Quick Guide

2 MG18A402 - VLT®is a registered Danfoss trademark

1.2 Introduction

1.2.1 Available Literature

This Quick Guide contains the basic information necessary

for installing and running the frequency converter. If more

information is needed, literature can be found on the

enclosed cd or downloaded from:

www.danfoss.com/BusinessAreas/DrivesSolutions/Documen-

tations/Technical+Documentation.htm

1.2.2 Approvals

Table 1.2

IP54 enclosure frequency converter

do not have UL approvals.

Table 1.3

1.2.3 IT Mains

CAUTION

IT Mains

Installation on isolated mains source, that is, IT mains.

Max. supply voltage allowed when connected to mains:

440 V (3x380-480 V units).

On IP20 200-240 V 0.25-11 kW and 380-480 V IP20 0.37-22

kW, open the RFI switch by removing the screw on the

side of the frequency converter when at IT grid.

130BB612.10

Illustration 1.1 IP20 200-240 V 0.25-11 kW, IP20 0.37-22 kW

380-480 V.

1 EMC screw

Table 1.4

130BC251.10

Illustration 1.2 IP54 400 V 0.75-18.5 kW

1EMC screw

Table 1.5

On all units, set to [Off] when operating in IT mains.

CAUTION

If reinserted, only use M3x12 screw.

Quick Guide VLT®HVAC Basic Drive Quick Guide

MG18A402 - VLT®is a registered Danfoss trademark 3

1.2.4 Avoid Unintended Start

While the frequency converter is connected to mains, the

motor can be started/stopped using digital commands, bus

commands, references or via the LCP.

•Disconnect the frequency converter from mains

whenever personal safety considerations make it

necessary to avoid unintended start of any

motors.

•To avoid unintended start, always press [Off/

Reset] before changing parameters.

1.2.5 Disposal Instruction

Equipment containing electrical components

must not be disposed of together with domestic

waste.

It must be separately collected with electrical

and electronic waste according to local and

currently valid legislation.

Table 1.6

1.3 Installation

1.3.1 Before Starting Repair Work

1. Disconnect FC 101 from mains (and external DC

supply, if present).

2. Wait as stated in Table 1.1 for discharge of the

DC-link.

3. Remove motor cable.

1.3.2 Side-by-Side Installation

The frequency converter can be mounted side-by-side and

requires the clearance above and below for cooling.

Power [kW] Clearance above/below [mm/inch]

Frame IP class 3x200-240 V 3x380-480 V 3x525-600 V

H1 IP20 0.25-1.5 0.37-1.5 100/4

H2 IP20 2.2 2.2-4 100/4

H3 IP20 3.7 5.5-7.5 100/4

H4 IP20 5.5-7.5 11-15 100/4

H5 IP20 11 18.5-22 100/4

H6 IP20 15-18.5 30-45 18.5-30 200/7.9

H7 IP20 22-30 55-75 37-55 200/7.9

H8 IP20 37-45 90 75-90 225/8.9

H9 IP20 2.2-7.5 100/4

H10 IP20 11-15 200/7.9

Table 1.7

NOTE

With IP21/Nema Type1 option kit mounted, a distance of

50 mm between the units is required.

Quick Guide VLT®HVAC Basic Drive Quick Guide

4 MG18A402 - VLT®is a registered Danfoss trademark

1.3.3 Dimensions

D

130BB614.10

130BC205.10

130BC246.10

Table 1.8

Enclosure Power [kW] Height [mm] Width [mm] Depth

[mm]

Mounting hole

[mm]

Max.

Weig

Frame IP Class 3x200-240 V 3x380-480 V 3x525-600 V A "A incl De-

coupling

Plate"

a B b C d e f kg

H1 IP20 0.25-1.5 0.37-1.5 195 273 183 75 56 168 9 4.5 5.3 2.1

H2 IP20 2.2 2.2-4.0 227 303 212 90 65 190 11 5.5 7.4 3.4

H3 IP20 3.7 5.5-7.5 255 329 240 100 74 206 11 5.5 8.1 4.5

H4 IP20 5.5-7.5 11-15 296 359 275 135 105 241 12.6 7 8.4 7.9

H5 IP20 11 18.5-22 334 402 314 150 120 255 12.6 7 8.5 9.5

H6 IP20 15-18.5 30-45 18.5-30 518 595/635

(45 kW)

495 239 200 242 - 8.5 15 24.5

H7 IP20 22-30 55-75 37-55 550 630/690

(75 kW)

521 313 270 335 - 8.5 17 36

H8 IP20 37-45 90 75-90 660 800 631 375 330 335 - 8.5 17 51

H9 IP20 2.2-7.5 269 374 257 130 110 205 11 5.5 9 6.6

H10 IP20 11-15 399 419 380 165 140 248 12 6.8 7.5 12

I2 IP54 0.75-4.0 332 - 318.5 115 74 225 11 5.5 9 5.3

I3 IP54 5.5-7.5 368 - 354 135 89 237 12 6.5 9.5 7.2

I4 IP54 11-18.5 476 - 460 180 133 290 12 6.5 9.5 13.8

I5 IP54 11-18.5 480 - 454 242 210 260 19 9 9 23

I6 IP54 22-37 650 - 624 242 210 260 19 9 9 27

I7 IP54 45-55 680 - 648 308 272 310 19 9 9.8 45

I8 IP54 75-90 770 - 739 370 334 335 19 9 9.8 65

Table 1.9

Quick Guide VLT®HVAC Basic Drive Quick Guide

MG18A402 - VLT®is a registered Danfoss trademark 5

The dimensions are only for the physical units, but when

installing in an application it is necessary to add space for

free air passage both above and below the units. The

amount of space for free air passage is listed in Table 1.10:

Enclosure Clearance needed for free air passage [mm]

Frame IP class Above unit Below unit

H1 20 100 100

H2 20 100 100

H3 20 100 100

H4 20 100 100

H5 20 100 100

H6 20 200 200

H7 20 200 200

H8 20 225 225

H9 20 100 100

H10 20 200 200

I2 54 100 100

I3 54 100 100

I4 54 100 100

I5 54 200 200

I6 54 200 200

I7 54 200 200

I8 54 225 225

Table 1.10 Clearance Needed for Free Air Passage [mm]

1.3.4 Electrical Installation in General

All cabling must comply with national and local

regulations on cable cross-sections and ambient

temperature. Copper conductors required, (75 °C)

recommended.

Power [kW] Torque [Nm]

Frame IP class 3x200-240 V 3x380-480 V Line Motor DC

connection

Control

terminals

Earth Relay

H1 IP20 0.25-1.5 0.37-1.5 1.4 0.8 0.8 0.5 0.8 0.5

H2 IP20 2.2 2.2-4 1.4 0.8 0.8 0.5 0.8 0.5

H3 IP20 3.7 5.5-7.5 1.4 0.8 0.8 0.5 0.8 0.5

H4 IP20 5.5-7.5 11-15 1.2 1.2 1.2 0.5 0.8 0.5

H5 IP20 11 18.5-22 1.2 1.2 1.2 0.5 0.8 0.5

H6 IP20 15-18 30-45 4.5 4.5 - 0.5 3 0.5

H7 IP20 22-30 55 10 10 - 0.5 3 0.5

H7 IP20 - 75 14 14 - 0.5 3 0.5

H8 IP20 37-45 90 242242- 0.5 3 0.5

Table 1.11

Power [kW] Torque [Nm]

Frame IP class 3x380-480 V Line Motor DC connection Control

terminals

Earth Relay

I2 IP54 0.75-4.0 1.4 0.8 0.8 0.5 0.8 0.5

I3 IP54 5.5-7.5 1.4 0.8 0.8 0.5 0.8 0.5

I4 IP54 11-18.5 1.4 0.8 0.8 0.5 0.8 0.5

I5 IP54 11-18.5 1.8 1.8 - 0.5 3 0.6

I6 IP54 22-37 4.5 4.5 - 0.5 3 0.6

I7 IP54 45-55 10 10 - 0.5 3 0.6

I8 IP54 75-90 14/24114/241- 0.5 3 0.6

Table 1.12

Quick Guide VLT®HVAC Basic Drive Quick Guide

6 MG18A402 - VLT®is a registered Danfoss trademark

Power [kW] Torque [Nm]

Frame IP class 3x525-600 V Line Motor DC connection Control

terminals

Earth Relay

H9 IP20 2.2-7.5 1.8 1.8 not

recommended

0.5 3 0.6

H10 IP20 11-15 1.8 1.8 not

recommended

0.5 3 0.6

H6 IP20 18.5-30 4.5 4.5 - 0.5 3 0.5

H7 IP20 37-55 10 10 - 0.5 3 0.5

H8 IP20 75-90 14/24114/241- 0.5 3 0.5

Table 1.13 Details of Tightening Torques

1Cable dimensions

≤

95 mm2

2Cable dimensions >95 mm2

1.3.5 Connecting to Mains and Motor

The frequency converter is designed to operate all

standard three-phased asynchronous motors. For

maximum cross-section on wires see 1.6 General Specifi-

cations.

•Use a shielded/armored motor cable to comply

with EMC emission specifications, and connect

this cable to both the decoupling plate and the

motor metal.

•Keep motor cable as short as possible to reduce

the noise level and leakage currents.

•For further details on mounting of the

decoupling plate, see FC 101 De-coupling Plate

Mounting Instruction MI02Q.

•Also see EMC-Correct Installation in the VLT

HVAC

Basic Design Guide, MG18C.

1. Mount the earth wires to earth terminal.

2. Connect motor to terminals U, V and W.

3. Mount mains supply to terminals L1, L2 and L3

and tighten.

130BB634.10

Motor

UVW-DC+DC

MAINS

Illustration 1.3 H1-H5 Frame

IP20 200-240 V 0.25-11 kW and IP20 380-480 V 0.37-22 kW.

1Line

2 Earth

3 Motor

4 Relays

Table 1.14

Quick Guide VLT®HVAC Basic Drive Quick Guide

MG18A402 - VLT®is a registered Danfoss trademark 7

L1 91 / L2 92 / L3 93

U 96 / V 97 / W 98

03 02 01

06 05 04

234

130BB762.10

Illustration 1.4 H6 Frame

IP20 380-480 V 30-45 kW

IP20 200-240 V 15-18.5 kW

IP20 525-600 V 22-30 kW

1 Line

2 Motor

3 Earth

4 Relays

Table 1.15

130BB763.10

Illustration 1.5 H7 Frame

IP20 380-480 V 55-75 kW

IP20 200-240 V 22- 30 kW

IP20 525-600 V 45-55 kW

1Line

2 Relays

3 Earth

4 Motor

Table 1.16

Quick Guide VLT®HVAC Basic Drive Quick Guide

8 MG18A402 - VLT®is a registered Danfoss trademark

130BB764.10

L1 L1 L1 UVw

Illustration 1.6 H8 Frame

IP20 380-480 V 90 kW

IP20 200-240 V 37-45 kW

IP20 525-600 V 75-90 kW

1 Line

2 Relays

3 Earth

4 Motor

Table 1.17

MOTOR

U V W

130BT302.12

Illustration 1.7 H9 Frame

IP20 600 V 2.2-7.5 kW

-DC+DC

BR- BR+ U V W

M A I N S

RELAY 1 RELAY 2

- LC +

130BA261.10

Illustration 1.8

130BA262.10

I N S

+DC

BR- BR+ UVW

RELAY 1 RELAY 2

Illustration 1.9

Quick Guide VLT®HVAC Basic Drive Quick Guide

MG18A402 - VLT®is a registered Danfoss trademark 9

Andere Handbücher für VLT HVAC Basic Drive FC 101

Inhaltsverzeichnis

Andere Danfoss Gleichstromantrieb Handbücher

Danfoss

Danfoss VLT HVAC FC 100 Bedienungsanleitung

Danfoss

Danfoss VLT AQUA Drive FC 200 Betriebsanleitung

Danfoss

Danfoss FC 301 Bedienungsanleitung

Danfoss

Danfoss VLT AQUA Drive FC 202 Leitfaden

Danfoss

Danfoss VLT HVAC Drive FC 102 Bedienungsanleitung

Danfoss

Danfoss VLT 5000 Series Gebrauchsanweisung

Danfoss

Danfoss VLT HVAC Drive Metasys N2 Bedienungsanleitung

Danfoss

Danfoss VLT AQUA Drive FC 202 Bedienungsanleitung

Danfoss

Danfoss VLT AQUA Drive FC 202 Bedienungsanleitung

Danfoss

Danfoss VLT FC 103 Betriebsanleitung

Danfoss

Danfoss VLT FC 103 Leitfaden

Danfoss

Danfoss VLT AutomationDrive EZ FC 321 Betriebsanleitung

Danfoss

Danfoss VLT 5000 Series Bedienungsanleitung

Danfoss

Danfoss VLT DriveMotor FCM 106 Leitfaden

Danfoss

Danfoss VLT FC 100 Bedienungsanleitung

Danfoss

Danfoss VLT AutomationDrive FC 301 Bedienungsanleitung

Danfoss

Danfoss VLT AQUA Drive FC 202 Leitfaden

Danfoss

Danfoss VLT FCM Series Bedienungsanleitung

Danfoss

Danfoss VLT Micro Drive FC 51 Series Bedienungsanleitung

Danfoss

Danfoss VLT Leitfaden

Danfoss

Danfoss VLT AutomationDrive FC 300 Leitfaden

Danfoss

Danfoss FC 100 Series Betriebsanleitung

Danfoss

Danfoss VLT AutomationDrive FC 302 Bedienungsanleitung

Danfoss

Danfoss VLT AutomationDrive FC 301 Bedienungsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Bedienungsanleitung

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Stücklistenhandbuch

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung

Beckhoff

Beckhoff AX8911 Bedienerhandbuch