Danfoss VLT PROFINET MCA 120 Bedienungsanleitung
Installation Guide
VLT® PROFINET MCA 120
VLT® AutomationDrive FC 361
1 Introduction
1.1 Purpose of this Installation Guide
This installation guide provides information for quick replacement of a VLT® PROFINET MCA 120 interface in the VLT® AutomationDrive
FC 361.
The installation guide is intended for use by qualified personnel. Users are assumed to be familiar with the VLT® drive, with PROFINET
technology, and with the PC or PLC used as a master in the system.
Read the instructions before installation and ensure that instructions for safe installation are observed.
1.2 Trademarks
VLT® is a registered trademark for Danfoss A/S.
AN274237376992en-000101 / 130R0856 | 1
Danfoss A/S © 2019.03
2 Safety
2.1 Safety Precautions
WARNING
DISCHARGE TIME
The drive contains DC-link capacitors, which can remain charged even when the drive is not powered. High voltage can be
present even when the warning indicator lights are off.
Failure to wait the specified time after power has been removed before performing service or repair work could result in death
or serious injury.
-Stop the motor.
-Disconnect AC mains, permanent magnet type motors, and remote DC-link supplies, including battery back-ups, UPS, and
DC-link connections to other drives.
-Wait for the capacitors to discharge fully. The minimum waiting time is specified in table Discharge time and is also visible
on the nameplate on top of the drive.
-Before performing any service or repair work, use an appropriate voltage measuring device to make sure that the capacitors
are fully discharged.
Table 1: Discharge Time
Voltage [V] Power range [kW (hp)] Minimum waiting time (minutes)
380–480 90–315 kW (125–450 hp) 20
Safety
Installation Guide | VLT® PROFINET MCA 120
AN274237376992en-000101 / 130R0856
2 | Danfoss A/S © 2019.03
3 Technical Data
3.1 Cabling Requirements
• Choose suitable media for Ethernet data transmission. CAT5e and CAT6 cables are recommended for industrial applications. Both
types are available as unshielded twisted pair and shielded twisted pair.
• Shielded cables are recommended for use in industrial environments and with drives.
• A maximum cable length of 100 m (328 ft) is allowed between the switches.
3.2 Cable Specifications
PROFINET cables used are based electrically on category 5 balanced LAN cables according to ISO/IEC 11801 Edition 2.0, Class D.
Type C cables can be used in special applications (for example, the use of trailing cables and frequently moved machine parts), even
though their design and mechanical parameters can deviate from the specifications of type A and type B cables. Still, most of the
electrical parameters (for example, impedance levels) are retained.
Highly flexible copper cables generally have the finest stranded conductors and a highly resistant polyurethane outer sheath. Various
outer sheath materials are permitted to meet the various demands regarding resistance of industrial environments and exterior/
underground laying (natural and synthetic oil, grease, coolants/lubricants, chemicals, high and low temperatures, UV radiation, and so
on).
Table 2: Cable Specifications for Application Types A, B and C
Cable type Application type A Application type B Application type C
Design Data cable Data cable Data cable
Cable installation type Stationary, no movement after
installation.
Flexible, occasional movement
or vibration.
Special applications (for example,
highly flexible, permanent move-
ment, vibration, or torsion).
Cable marking PROFINET type A PROFINET type B PROFINET type C
Core cross-section AWG 22/1 AWG 22/7 AWG 22/..
Outer diameter 5.5–8.0 mm (0.22–0.31 in) Application dependent
Core diameter 1.5 ± 0.1 mm (0.06 ± 0.004 in) Application dependent
Color (outer sheath) Green RAL6018 Application dependent
Core identification (col-
ors)
star quad 2 pair
White, yellow, blue, orange
Pair 1: white (RXD+), blue (RXD-) Pair 2: yellow (TXD+), orange (TXT-)
Number of cores 4
Cable design 2 pairs or 1 star quad
Shielding design type Aluminum foil + Cu braiding Application
Plug type RJ 45 (IP20 or IP65/67)/M12
Table 3: Transmission Performance Requirements
Relevant standard ISO/IEC 11801 Edition 2.0, IEC 61156 (minimum Category 5)
Technical Data
Installation Guide | VLT® PROFINET MCA 120
AN274237376992en-000101 / 130R0856 | 3
Danfoss A/S © 2019.03
Delay skew ≤20 ns/100 m
Transfer impedance ≤50 m Ω/m at 10 MHz
Technical Data
Installation Guide | VLT® PROFINET MCA 120
AN274237376992en-000101 / 130R0856
4 | Danfoss A/S © 2019.03
4 Installation
4.1 Mounting
Procedure
1. Make sure that the power to the drive is disconnected.
2. Remove the front cover from the drive.
3. Remove the LCP (Local Control Panel) or blind cover, and then remove the LCP cradle from the drive.
4. Disconnect the communication cables from the existing MCA option card.
5. Remove the existing MCA option card from the drive.
6. Fit the new VLT® PROFINET MCA 120 option card into slot A. Mount the option with the Ethernet port facing up for top cable entry.
7. Connect the Ethernet cables. See illustration 1 and table 4 for the definition of PROFINET connectors.
e30bd910.10
2
4
3
M12 PIN#
RJ45
8
1
1
. . . . . .
Illustration 1: PROFINET Connectors
Table 4: PROFINET Connectors
Signal M12 PIN# RJ 45
RX + 1 1
TX + 2 2
RX - 3 3
TX - 4 4
8. Set the address switches if needed.
9. Fit the LCP cradle.
10. Fit the LCP or blind cover in the LCP cradle.
11. Fit the front cover on the drive.
12. Connect power to the drive.
4.2 Setting Address Switches
The option has address switches that are used to set the station name (host name).
• When all switches are set to ON, or all are set to OFF, change the station name via 12-08 Host Name or via DCP command.
• In all other combinations, the address switches have priority over the parameter setting. The station name is set based on the value
in 15-40 FC Type, and a 3-digit number selected from the DIP settings.
Installation
Installation Guide | VLT® PROFINET MCA 120
AN274237376992en-000101 / 130R0856 | 5
Danfoss A/S © 2019.03
B:08:XX:XX:XX
Option A
134B6779
Host Name
8 7 6 5 4 3 2 1
OFF
ON
Ethernet Port 2
e30bd786.11
Illustration 2: Address Switches
Use the address switches to set the 253 different station names according to table 5.
Table 5: Host Names Setting
Switch 8 7 6 5 4 3 2 1
12-08 Host Name +128 +64 +32 +16 +8 +4 +2 +1
005 OFF OFF OFF OFF OFF ON OFF ON
035 OFF OFF ON OFF OFF OFF ON ON
082 OFF ON OFF ON OFF OFF ON OFF
212 ON ON OFF ON OFF ON OFF OFF
The station name change comes into effect at the next power-up. Read the station name in 12-08 Host Name.
Installation
Installation Guide | VLT® PROFINET MCA 120
AN274237376992en-000101 / 130R0856
6 | Danfoss A/S © 2019.03
4.3 Wiring Procedures
Procedure
1. Mount the pre-configured cable wires with the connectors on the fieldbus option. For cable specifications, refer to 3.2 Cable
Specifications.
e30bg792.10
Illustration 3: Wiring
2. Fix the cable to the metal base plate using the springs.
3. Tie down the cable and route it with other control wires inside the unit.
NOTICE
Do not strip the Ethernet cable. Ground the shielded Ethernet cables through the RJ45 connector on the PROFINET
interface.
Installation
Installation Guide | VLT® PROFINET MCA 120
AN274237376992en-000101 / 130R0856 | 7
Danfoss A/S © 2019.03
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products
already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective
companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
Danfoss A/S
Ulsnaes 1
DK-6300 Graasten
vlt-drives.danfoss.com
Danfoss A/S © 2019.03 MG06N102*MG06N102*AN274237376992en-000101/ 130R0856
Installation
Installation Guide | VLT® PROFINET MCA 120
Andere Handbücher für VLT PROFINET MCA 120
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Danfoss Gleichstromantrieb Handbücher
Danfoss
Danfoss VLT FC 322 Bedienungsanleitung
Danfoss
Danfoss VLT Automation Drive FC 360 Betriebsanleitung
Danfoss
Danfoss VLT FC 300 Bedienungsanleitung
Danfoss
Danfoss VLT FC 103 Bedienungsanleitung
Danfoss
Danfoss VLT PROFINET MCA 120 Bedienungsanleitung
Danfoss
Danfoss VLT FC 100 Bedienungsanleitung
Danfoss
Danfoss VLT Bedienungsanleitung
Danfoss
Danfoss AME 25 SU Bedienungsanleitung
Danfoss
Danfoss FC 301 Bedienungsanleitung
Danfoss
Danfoss ADAP-KOOL AKD 102 Bedienungsanleitung
Danfoss
Danfoss VLT HVAC Drive Metasys N2 Bedienungsanleitung
Danfoss
Danfoss AMV 410 Bedienungsanleitung
Danfoss
Danfoss vlt fcd 302 Bedienungsanleitung
Danfoss
Danfoss VLT AutomationDrive FC 303 Bedienungsanleitung
Danfoss
Danfoss VLT HVAC Drive FC 102 Bedienungsanleitung
Danfoss
Danfoss VLT AutomationDrive FC 301 Betriebsanleitung
Danfoss
Danfoss MCD 500 Bedienungsanleitung
Danfoss
Danfoss VLT HVAC Basic Drive FC 101 Bedienungsanleitung
Danfoss
Danfoss VLT Brake Resistor MCE 101 Leitfaden
Danfoss
Danfoss VLT AutomationDrive FC 300 Bedienungsanleitung
Beliebte Gleichstromantrieb Handbücher anderer Marken
Vincent Associates
Vincent Associates UNIBLITZ ED12DSS Bedienungsanleitung
EKSMA OPTICS
EKSMA OPTICS DQ-100-4 Stücklistenhandbuch
Chamberlain Garog
Chamberlain Garog D Series Bedienungsanleitung
Parker
Parker PDS Series Bedienungsanleitung
Festo
Festo DGC G Series Einrichtungshandbuch
Binks
Binks QS-5012-1-CE Bedienungsanleitung
