Danfoss VLT series Bedienungsanleitung

Installation Guide

VLT® 24 V DC Supply MCB 107

VLT® Series FC 102, FC 103, FC 202, and FC 301/FC

302

1 Scope of Delivery, Safety, and Installation

1.1 Purpose of the Manual

This installation guide describes the installation of the VLT®24 V DC Supply MCB 107.

1.2 Purpose of the VLT® 24 V DC Supply MCB 107

VLT®24 V DC Supply MCB 107 option is a low voltage supply to the control card or any option card installed. This option keeps the

control section (including parameter configurations) and any installed option alive during a power failure.

NOTICE

External power supply

To achieve the intended functionality, an external 24 V DC supply as specified below has to be connected to the terminals of

the option.

Specifications for VLT 24 V DC Supply MCB 107

Specification Value

Input voltage range 24 V DC ±15% (maximum 37 V for 10 s)

Maximum input current 2.2 A

Average input current for FC 301/FC 302 0.9 A

Maximum cable length 75 m (246 ft)

Input capacitance load <10 uF

Power-up delay <0.6 s

Connection terminals

• Terminal 35: - external 24 V DC supply

• Terminal 36: + external 24 V DC supply

AN287957936346en-000101 / 130R0308 | 1

3536

e30ba028.11

Illustration 1: Connection to MCB 107 on Enclosure Sizes A2 and A3

1.3 Items Supplied

The VLT®24 V DC Supply MCB 107 is available in 2 versions: Standard and coated.

Table 1: Ordering Numbers

Version Ordering number

Standard 130B1108

Coated 130B1208

1.4 Safety Instructions

For important information about safety precautions for installation, refer to the product-specific operating guide.

WARNING

DISCHARGE TIME

The drive contains DC-link capacitors, which can remain charged even when the drive is not powered. High voltage can be

present even when the warning indicator lights are off.

Failure to wait the specified time after power has been removed before performing service or repair work could result in death

or serious injury.

-Stop the motor.

-Disconnect AC mains, permanent magnet type motors, and remote DC-link supplies, including battery back-ups, UPS, and

DC-link connections to other drives.

-Wait for the capacitors to discharge fully. The minimum waiting time is specified in the table Discharge time and is also

visible on the nameplate on top of the drive.

-Before performing any service or repair work, use an appropriate voltage measuring device to make sure that the capacitors

are fully discharged.

Scope of Delivery, Safety, and Installation

Installation Guide | VLT® 24 V DC Supply MCB 107

AN287957936346en-000101 / 130R0308

Table 2: Discharge Time, VLT® HVAC Drive FC 102 and VLT® Refrigeration Drive FC 103

Voltage [V] Minimum waiting time (minutes)

4 7 15

200–240 1.1–3.7 kW (1.5–5 hp) – 5.5–45 kW (7.5–60 hp)

380–480 1.1–7.5 kW (1.5–10 hp) – 11–90 kW (15–125 hp)

525–600 1.1–7.5 kW (1.5–10 hp) – 11–90 kW (15–125 hp)

525–690 – 1.1–7.5 kW (1.5–10 hp) (FC 102 only) 11–90 kW (15–125 hp) (FC 102 only)

Table 3: Discharge Time, VLT® AQUA Drive FC 202

Voltage [V] Minimum waiting time (minutes)

4 7 15

200–240 0.25–3.7 kW (0.34–5 hp) – 5.5–45 kW (7.5–60 hp)

380–480 0.37–7.5 kW (0.5–10 hp) – 11–90 kW (15–125 hp)

525–600 0.75–7.5 kW (1.0–10 hp) – 11–90 kW (15–125 hp)

525–690 – 1.1–7.5 kW (1.5–10 hp) 11–90 kW (15–125 hp)

Table 4: Discharge Time, VLT® AutomationDrive FC 301/FC 302

Voltage [V] Minimum waiting time (minutes)

4 7 15

200–240 0.25–3.7 kW (0.34–5 hp) – 5.5–37 kW (7.5–50 hp)

380–500 0.25–7.5 kW (0.34–10 hp) – 11–75 kW (15–100 hp)

525–600 0.75–7.5 kW (1–10 hp) – 11–75 kW (15–100 hp)

525–690 – 1.5–7.5 kW (2–10 hp) 11–75 kW (15–100 hp)

1.5 Installing the D-Option

Prerequisites:

The following tools are required for installing the option:

• Torx 10 screwdriver.

• Flat-head screwdriver.

Scope of Delivery, Safety, and Installation

Installation Guide | VLT® 24 V DC Supply MCB 107

AN287957936346en-000101 / 130R0308 | 3

Procedure

1. Disconnect power to the drive.

2. Disconnect power to the live part connections on the relay terminals.

3. Remove the LCP or the blind cover.

4. Remove the terminal cover.

5. Remove the control cables.

6. Remove the cable decoupling plate.

For enclosure sizes A2 and A3, also remove the plastic cover underneath the decoupling plate (if installed).

7. Insert the option in the D-option slot.

8. Mount the cable decoupling plate.

9. Connect the control cables and relieve the cables with the enclosed cable strips.

10. Attach the terminal cover and the LCP, or the blind cover.

11. Connect power to the drive.

Example:

e30bg046.10

1LCP

3Cable decoupling plate

5D-option slot

2Terminal cover

4D-option

Illustration 2: Installing a D-Option in an A2/A3 Enclosure

Scope of Delivery, Safety, and Installation

Installation Guide | VLT® 24 V DC Supply MCB 107

AN287957936346en-000101 / 130R0308

Scope of Delivery, Safety, and Installation

Installation Guide | VLT® 24 V DC Supply MCB 107

AN287957936346en-000101 / 130R0308

Scope of Delivery, Safety, and Installation

Installation Guide | VLT® 24 V DC Supply MCB 107

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products

already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective

Danfoss A/S

Ulsnaes 1

DK-6300 Graasten

vlt-drives.danfoss.com

Andere Handbücher für VLT series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Danfoss Gleichstromantrieb Handbücher

Danfoss

Danfoss VLT CDS 803 Bedienungsanleitung

Danfoss

Danfoss NEMA-3R Bedienungsanleitung

Danfoss

Danfoss VLT AutomationDrive FC 300 Bedienungsanleitung

Danfoss

Danfoss VLT AutomationDrive FC 301 Betriebsanleitung

Danfoss

Danfoss VLT AutomationDrive FC 300 Series Betriebsanleitung

Danfoss

Danfoss VLT AutomationDrive FC 301 Betriebsanleitung

Danfoss

Danfoss VLT AutomationDrive FC 301 Leitfaden

Danfoss

Danfoss FC 300 Bedienungsanleitung

Danfoss

Danfoss VLT FC 103 Bedienungsanleitung

Danfoss

Danfoss ADAP-KOOL AKD 102 Bedienungsanleitung

Danfoss

Danfoss VLT AQUA Drive FC 202 Bedienungsanleitung

Danfoss

Danfoss ADAP-KOOL Drive Betriebsanleitung

Danfoss

Danfoss VLT HVAC Drive FC 102 Leitfaden

Danfoss

Danfoss VLT HVAC Drive FC 102 Bedienungsanleitung

Danfoss

Danfoss VLT AQUA Drive FC 200 Bedienungsanleitung

Danfoss

Danfoss vlt aqua Bedienungsanleitung

Danfoss

Danfoss VLT series Bedienungsanleitung

Danfoss

Danfoss VLT AQUA Drive FC 202 Bedienungsanleitung

Danfoss

Danfoss vlt fcd 302 Bedienungsanleitung

Danfoss

Danfoss FC 302 Bedienungsanleitung

Danfoss

Danfoss VLT HVAC Basic Drive FC 101 Bedienungsanleitung

Danfoss

Danfoss VLT AQUA Drive FC 202 Bedienungsanleitung

Danfoss

Danfoss vlt aqua Bedienungsanleitung

Danfoss

Danfoss AMV 438 SU Bedienungsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Bedienungsanleitung

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Stücklistenhandbuch

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung

Beckhoff

Beckhoff AX8911 Bedienerhandbuch