Danfoss VLT 2811 Bedienungsanleitung

(217) 352-9330 | [email protected] | artisantg.com

ARTISAN

TECHNOLOGY

GROUP

Your definitive source

for

quality

pre-owned

equipment.

Artisan Technology

Group

Full-service,

independent

repair

center

with

experienced

engineers

and

technicians

on staff.

buy

your

excess,

underutilized,

and

idle

equipment

along

with

credit

for

buybacks

and

trade-ins

Custom

engineering

your

equipment

works

exactly as

you

specify.

•

Critical

and

expedited

services

•

Leasing

Rentals/

Demos

• In

stock/

Ready-to-ship

•

!TAR-certified

secure

asset

solutions

Expert

team

ITrust

guarantee

100%

satisfaction

All

ademarks,

names, a

s a

earing here

are

e property of

pecti

ner

Find the Danfoss VLT 2811 at our website: Click HERE

1QuickGuide

1.1 Safety

1.1.1 Warnings

High Voltage Warning:

The voltage of the frequency converter is dangerous whenever it is connected to

mains. Incorrect installation of the motor or frequency converter may cause damage

to the equipment, serious injury or death. Consequently, it is essential to comply

with the instructions in this manual as well as local and national rules and safety

regulations.

Warning:

Touching the electrical parts may be fatal - even after the equipment has been dis-

connected from mains.Also make sure that other voltage inputs have been discon-

nected (linkage of DC intermediate circuit). Be aware that there may be high voltage

on the DC link even when the LEDs are turned off. Before touching any potentially

live parts of the frequency converter, wait at least 4 minutes.

Leakage Current:

The earth leakage current from the frequency converter exceeds 3.5 mA. According

to IEC 61800-5-1 a reinforced Protective Earth connection must be ensured by

means of a min. 10mm² Cu or an addtional PE wire - with the same cable cross

section as the Mains wiring - must be terminated separately.

To increase safety, install an RCD

Residual Current Device:

This product can cause a DC current in the protective conductor. Where a residual

current device (RCD) is used for extra protection, only an RCD of Type B (time de-

layed) shall be used on the supply side of this product. See also Danfoss Application

Note on RCD, MN.90.GX.YY.

Protective earthing of the frequency converter and the use of RCDs must always

follow national and local regulations.

Motor Thermal Protection:

Protection against Motor overload is not included in the factory setting. If this func-

tion is required, set par. 128

Motor Thermal Protection

to data value

ETR trip

or data

value

ETR warning

. For the North American market: The ETR functions provide

overload protection of the motor, class 20, in accordance with NEC.

Installation in high altitudes:

For altitudes above 2 km, please contact Danfoss regarding PELV.

VLT 2800 Quick Guide 1 Quick Guide

MG.28.M1.02 - VLT®is a registered Danfoss trademark

1.1.2 Safety Instructions

• The frequency converter must be disconnected from the mains if repair work is to be

carried out. Check that the mains supply has been disconnected and the prescribed time

has passed before removing motor and mains plugs.

• Make sure the frequency converter is properly connected to earth.

• Protect users against supply voltage.

• Protect the motor against overloading according to national and local regulations.

• The earth leakage current exceeds 3.5 mA. For ELCB types, please see application note

MN.90.GX.YY.

• The [STOP/RESET] key on the control panel of the frequency converter does not dis-

connect the equipment from mains and is thus not to be used as a safety switch.

• Note that the frequency converter has more voltage inputs than L1, L2 and L3 when DC

bus terminals are used. Check that all voltage inputs are disconnected and that the pre-

scribed time has passed before repair work is commenced.

1.1.3 Warning against unintended start

1. The motor can be brought to a stop by means of digital commands, bus commands,

references or a local stop, while the frequency converter is connected to mains. If per-

sonal safety considerations make it necessary to ensure that no unintended start oc-

curs, these stop functions are not sufficient.

2. While parameters are being changed, the motor may start. Consequently, the stop key

[STOP/RESET] must always be activated, following which data can be modified.

3. A motor that has been stopped may start if faults occur in the electronics of the frequency

converter, or if a temporary overload or a fault in the supply mains or the motor con-

nection ceases.

1.1.4 Use on Isolated Mains

See section

RFI Switch

in the operating instructions regarding use on isolated mains.

It is important to follow the recommendations regarding installation on IT-mains, since sufficient

protection of the complete installation must be observed. Not taking care using relevant moni-

toring devices for IT-mains may result in damage.

1 Quick Guide VLT 2800 Quick Guide

MG.28.M1.02 - VLT®is a registered Danfoss trademark

1.2 Introduction

Use this Quick Guide to carry out quick and

EMC-correct installation of the frequency con-

verter in five steps.

Read the safety section before

installing the unit.

NB!

The Operating Instructions, MG.

27.AX.YY, give further examples

of installation and describe all

functions in detail.

The Design Guide, MG.

27.EX.YY, contains extensive in-

formation.

1.2.1 Abbreviations

ELCB Earth Leakage Circuit Breakers

NO Normally open

NC Normally closed

PD2 Dual phase (for 2822, 2840 that only run 3-phase as standard D2), 220 - 240 V

RCD Residual Current Device

1.2.2 Available Litterature

NB!

This quick guide contains only the very basic information necessary for installing and

running the drive.

For more information please consult the VLT 2800 Design Guide, MG.27.EX.YY

VLT 2800 Quick Guide 1 Quick Guide

MG.28.M1.02 - VLT®is a registered Danfoss trademark

Title Literature no.

VLT 2800 Operating Instructions MG.27.AX.YY

VLT 2800 Design Guide MG.27.EX.YY

VLT 2800 Data Sheet MD.27.AX.YY

Mounting Instruction for VLT 2800 MI.28.AX.YY

VLT 2800 Filter Instruction MI.28.BX.YY

Precise Stop MI.28.CX.YY

Cold Plate MI.28.DX.YY

VLT 2800 NEMA 1 Terminal Covering MI.28.EX.YY

VLT 2800 DeviceNet Cable MI.28.FX.YY

VLT 2800 Blue Star Condensing Unit MI.28.GX.YY

VLT 2880 - 2882 Spare Part Instruction MI.28.HX.YY

Wobble Function MI.28.JX.YY

VLT 2800 LCP Remote-mounting Kit MI.56.AX.YY

User Instruction for LOP MI.90.EX.YY

Brake Resistor MI.90.FX.YY

Profibus DP Manual MG.90.AX.YY

VLT 2800 DeviceNet Manual MG.90.BX.YY

Metasys N2 Manual MG.90.CX.YY

Profibus Manual MG.90.EX.YY

Output Filter Manual MG.90.NX.YY

Brake Resistor Manual MG.90.OX.YY

MCT-10 Manual MG.10.RX.YY

Modbus RTU Manual MG.10.SX.YY

Protection against Electrical Hazards MN.90.GX.YY

X = Revision Number, Y = Language code

Application notes can be found on

http://www.danfoss.com/BusinessAreas/DrivesSolutions/Doc-

umentations/Technical+Documentation.htm

1.2.3 Approvals

1.2.4 Disposal Instruction

Equipment containing electrical components must not be disposed of

together with domestic waste.

It must be separately collected with electrical and electronic waste

according to local and currently valid legislation.

1.3 Mechanical Installation

VLT 2800 frequency converters allow side-by-side installation on a wall in any position as the units

do not require ventilation on the side. Because of the need for cooling, there must be 10 cm free

air passage above and below the frequency converter.

All units with enclosure IP 20 must be integrated in cabinets and panels. IP 20 is not suitable for

remote mounting. In some countries, e.g. in the USA, units with enclosure NEMA 1 are approved

for remote mounting.

1 Quick Guide VLT 2800 Quick Guide

MG.28.M1.02 - VLT®is a registered Danfoss trademark

NB!

With the IP 21 solution all units require a minimum of 100 mm air on each side. This

means that side-by-side mounting is NOT allowed.

Size mm A a B b C D E øa øb Føc

VLT 2803 - 2815 200 191 75 60 168 7 5 4.5 8 4 4.5

VLT 2822* 267.5 257 90 70 168 8 6 5.5 11 4.5 5.5

VLT 2840* 267.5 257 140 120 168 8 6 5.5 11 4.5 5.5

PD2

VLT 2822 267.5 257 140 120 168 8 6 5.5 11 4.5 5.5

VLT 2840 505 490 200 120 244 7.75 7.25 6.5 13 86.5

VLT 2822 267.5 257 90 70 168 8 6 5.5 11 4.5 5.5

VLT 2840 267.5 257 140 120 168 8 6 5.5 11 4.5 5.5

VLT 2805 - 2815 200 191 75 60 168 7 5 4.5 8 4 4.5

VLT 2822 - 2840 267.5 257 90 70 168 8 6 5.5 11 4.5 5.5

VLT 2855 - 2875 267.5 257 140 120 168 8 6 5.5 11 4.5 5.5

VLT 2880 - 2882 505 490 200 120 244 7.75 7.25 6.5 13 86.5

Table 1.1: * Only 3-phase

Drill holes in accordance with the measurements given in the above table. Please note the differ-

ence in unit voltages.

Retighten all four screws.

Fit the decoupling plate to the power cables and the earth screw (terminal 95).

1.3.1 Motor coils (195N3110) and RFI 1B filter (195N3103)

Illustration 1.1: Motor coils

VLT 2800 Quick Guide 1 Quick Guide

MG.28.M1.02 - VLT®is a registered Danfoss trademark

1.3.2 Terminal cover

The drawing below gives the dimensions for NEMA 1 terminal covers for VLT 2803-2875.

Dimension 'a' depends on the unit type.

1.3.3 IP 21 solution

Type Code number A B C

VLT 2803-2815 200-240 V,

VLT 2805-2815 380-480 V

195N2118 47 80 170

VLT 2822 200-240 V,

VLT 2822-2840 380-480 V

195N2119 47 95 170

VLT 2840 200-240 V,

VLT 2822 PD2, TR1 2855-2875

380-480 V

195N2120 47 145 170

TR1 2880-2882 380-480 V,

VLT 2840 PD2

195N2126 47 205 245

Table 1.2: Dimensions

1 Quick Guide VLT 2800 Quick Guide

MG.28.M1.02 - VLT®is a registered Danfoss trademark

1.3.4 EMC filter for long motor cables

Filter Dimensions

192HA719

A B C øa D E F G

20 204 20 5.5 8 234 27.5 244

H I øb J K L M N

75 45 6190 60 16 24 12

192H4720 A B C øa D E F G

20 273 20 5.5 8 303 25 313

H I øb J K L M N

90 50 6 257 70 16 24 12

192H4893 A B C øa D E F G

20 273 20 5.5 8 303 25 313

H I øb J K L M N

140 50 6 257 120 16 24 12

VLT 2800 Quick Guide 1 Quick Guide

MG.28.M1.02 - VLT®is a registered Danfoss trademark

1.4 Electrical Installation

1.4.1 Electrical Installation in General

NB!

All cabling must comply with national and local regulations on cable cross-sections

and ambient temperature. Copper conductors required, (60-75° C) recommended.

Details of terminal tightening torques.

VLT Terminals Torque (Nm) Torque, Control Cables (Nm)

2803 - 2875 Power mains brake 0.5 - 0.6

0.22 - 0.25

Earth 2 - 3

2880 - 2882,

2840 PD2

Power mains brake 1.2 - 1.5

Earth 2 - 3

Table 1.3: Tightening of terminals.

1.4.2 Power Cables

NB!

Please note that the power terminals can be removed.

Connect mains to the mains terminals of the frequency converter, i.e. L1, L2 and L3 and the earth

connection to terminal 95.

VLT 2803 - VLT 2815 VLT 2822 - VLT 2840

1 Quick Guide VLT 2800 Quick Guide

MG.28.M1.02 - VLT®is a registered Danfoss trademark

VLT 2880 - VLT

2882

Fit screened/armoured cable from the motor to the motor terminals of the frequency converter,

i.e. U, V, W. The screen ends in a screen connector.

1.4.3 Mains connection

NB!

Please note that at 1 x 220-240 Volt the neutral wire must be attached to terminal

(L2)

and the phase wire must be connected to terminal L1

(L1)

No. N

(L2)

(L1) (L3)

Mains voltage 1 x 220-240 V

NL1

No. 95 Earth connection

No. N

(L2)

(L1) (L3)

Mains voltage 3 x 220-240 V

L2 L1 L3

No. 95 Earth connection

No. 91 92 93 Mains voltage 3 x 380-480 V

L1 L2 L3

No. 95 Earth connection

NB!

Please check that the mains voltage fits the mains voltage of the frequency con-

verter, which can be seen from the nameplate.

400-Volt units with RFI-filters may not be connected to mains supplies in which the

voltage between phase and earth is more than 300 Volts. Please note that for the

IT mains and the delta earth the mains voltage can exceed 300 Volts between phase

and earth. Units with type code R5 (IT mains) can be connected to mains supplies

with up to 400 V between phase and earth.

See

Technical data

for correct dimensioning of cable cross-section. See also the section entitled

Galvanic isolation

in the Operating Instructions for further details.

VLT 2800 Quick Guide 1 Quick Guide

MG.28.M1.02 - VLT®is a registered Danfoss trademark

Inhaltsverzeichnis

Andere Danfoss Medienkonverter Handbücher

Danfoss

Danfoss VLT MCA 121 EtherNet/IP Bedienungsanleitung

Danfoss

Danfoss iC7 Series Bedienungsanleitung

Danfoss

Danfoss iC7 Series Bedienungsanleitung

Danfoss

Danfoss 102 Bedienungsanleitung

Danfoss

Danfoss VLT Midi Drive FC 280 Bedienungsanleitung

Danfoss

Danfoss iC7 FA09-FA12 Bedienungsanleitung

Danfoss

Danfoss VLT AutomationDrive FC 301 Bedienungsanleitung

Danfoss

Danfoss FC 100 Series Bedienungsanleitung

Danfoss

Danfoss FCM 300 PROFIBUS Bedienungsanleitung

Danfoss

Danfoss VLT AutomationDrive FC 301 Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Konfigurationshandbuch

Danfoss

Danfoss VLT HVAC Basic Drive FC 101 Betriebsanleitung

Danfoss

Danfoss HJM022D20Q Bedienungsanleitung

Danfoss

Danfoss VLT 3000 Series Referenzhandbuch

Danfoss

Danfoss VLT PROFIBUS DP MCA 101 Bedienungsanleitung

Danfoss

Danfoss VLT AutomationDrive FC 300 Bedienungsanleitung

Danfoss

Danfoss VLT FC 103 Bedienungsanleitung

Danfoss

Danfoss Vacon NXP Leitfaden

Danfoss

Danfoss VLT AQUA Drive Series Leitfaden

Danfoss

Danfoss EC-C1700B-420 Bedienungsanleitung

Danfoss

Danfoss D9h Bedienungsanleitung

Danfoss

Danfoss EC-C1200-450 Bedienungsanleitung

Danfoss

Danfoss VLT DeviceNet MCA 104 Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung